radio MAZDA MODEL TRIBUTE 2006 Owners Manual (in English)
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2006, Model line: MODEL TRIBUTE, Model: MAZDA MODEL TRIBUTE 2006Pages: 288, PDF Size: 2.6 MB
Page 22 of 288

Press and hold CLOCK for approximately two seconds until a beep
sound is heard. The clock’s current time will flash. Press SCAN
adjust the hours. Press AUTO-M to adjust the minutes. Press CLOCK
again to start the clock.
NOTE: If the audio operation is selected while the clock mode is on, the
selected audio mode will be displayed for ten seconds, then the display
will revert to the clock mode.
NOTE: If the power supply to the unit is interrupted (if the fuse blows
or the vehicle’s battery is disconnected), the clock will need to be reset.
NOTE: If the time is not adjusted while the clock’s current time is
flashing (if neither H nor M is pressed), and the clock control is pressed
a second time, the minutes will be set to 00. If the clock’s current time
setting is within the latter part of the hour (from 30 to 59 min), the hour
setting will automatically advance one hour.
Setting military time: Press and hold CLOCK until the time in the
display flashes. Turn the TEXT control to the right or left to select either
12 or 24 HR. When your desired selection appears in the display, push
and hold the TEXT control until a beep is heard. The time will flash.
Press SCAN to adjust the hours. Press AUTO-M to adjust the minutes.
Press CLOCK again to start the clock.
4. Eject: Press to eject the CD.
5. SCAN/DISP/ESN/AUTO-M
SCAN: Press in radio or CD mode
for a brief sampling of all listenable
stations or of each CD track. Press
again to disable scan mode. If the
unit is left in scan mode, normal play will resume where scan was
selected.
DISP/ESN:
Your radio comes equipped with Satellite ready capability. This
enables you to view the song titles, artist, and further information. The kit
to enable Satellite reception is available through your dealer. Detailed
Satellite and instructions are included with the dealer installed kit.
AUTO-M: Auto memory tuning allows you to set strong radio stations
without losing your original manually set preset stations. This feature is
helpful on trips when you travel between cities with different radio
stations.
DISP/ESN
2006 Tribute (j14)
Owners Guide (post-2002-fmt)
USA (fus)
Entertainment Systems
22
Page 23 of 288

Press the FM/AM control to select a frequency. Press and momentarily
hold the AUTO-M (Auto memory) control. The system will beep. Press
the AUTO-M (Auto memory) control to select from the stored stations.
One stored station will be selected and played each time the control is
pressed. The frequency and channel number will be displayed.
NOTE:If no stations can be tuned after scanning operations, A will
appear in the display.
NOTE: If the power supply is interrupted, (fuse blows or the battery is
disconnected), the preset channels will be canceled.
6. TUNE: The TUNE control is a
multi-functional control which
works in radio and CD modes to
adjust the levels of bass, treble,
balance, fade, mid-range and
beep (off/on). Press to select
the desired function. Turn to
adjust the desired levels. TUNE
also works in radio mode to manually increase or decrease the
frequency.
7. Fast forward: In CD mode,
press and hold to advance
through a track at a high speed.
8. Rewind: In CD mode, press and
hold to reverse through a track
at a high speed.
9. PROG/RDM: Press during CD
play for a random selection of
songs. Press again to disengage
random play.
10. RPT: Press during CD play to
listen to a selection repeatedly.
RPT will illuminate in the
display and the current
selection will be repeated. Press
again to disengage repeat play.
2006 Tribute (j14)
Owners Guide (post-2002-fmt)
USA (fus)
Entertainment Systems
23
Page 24 of 288

11.DISC: Press to skip
forward to the beginning of the
next CD.
12.DISC
: Press to skip back
to the beginning of the previous
CD.
13.Volume/ON/OFF:Press to turn
the system on/off. Turn to
adjust the volume.
14.Memory presets:Your audio is
equipped with six station
memory preset controls. These
controls can be used to select
up to six preset AM stations and 12 FM stations (six in FM1 and six
in FM2).
Select a frequency with the AM/FM.
15.SEEK/TRACK/APC: SEEK
works in radio mode and allows
you to advance to all listenable
radio stations up (
)or
down (
) the radio
frequency.
Note:If you continue to press and hold the control, the frequency
will continue changing without stopping. Release the control after a
beep sounds.
TRACK:Works in CD mode and allows you to skip forward to the
beginning of the next track (
) or back to the beginning of the
current track (
).
APC (Auto program control):This feature works in tape mode and is
not operational on this system.
2006 Tribute(j14)
Owners Guide (post-2002-fmt)
USA(fus)
Entertainment Systems
24
Page 25 of 288

16.FM/AM:Press to enter radio mode and select a frequency from
FM1, FM2 or AM.
17.SAT:Your radio comes equipped with Satellite ready capability. This
enables you to view the song titles, artist, and further information.
The kit to enable Satellite reception is available through your dealer.
Detailed Satellite instructions are included with the dealer installed
kit.
AM/FM Stereo Six CD audio system — Satellite ready capability
(if equipped)
1.CD:To begin CD play, insert a
CD into the slot, label side up.
The system will load the CD and
begin play after a short pause.
The disc and track number will
illuminate in the display.
2006 Tribute(j14)
Owners Guide (post-2002-fmt)
USA(fus)
Entertainment Systems
25
Page 27 of 288

5.SCAN/DISP/ESN/AUTO-M
SCAN: Press in radio or CD mode
for a brief sampling of all listenable
stations or of each CD track. Press
again to disable scan mode. If the
unit is left in scan mode, normal play will resume where scan was
selected.
DISP/ESN: Your radio comes equipped with Satellite ready capability.
This enables you to view the song titles, artist, and further information.
The kit to enable Satellite reception is available through your dealer.
Detailed Satellite and instructions are included with the dealer installed
kit.
AUTO-M: Press the FM/AM control to select auto memory tuning which
allows you to set strong radio stations without losing your original
manually set preset stations. This feature is helpful on trips when you
travel between cities with different radio stations.
Press the FM/AM control to select a frequency. Press and momentarily
hold the AUTO-M (Auto memory) control. The system will beep. Press
the AUTO-M (Auto memory) control to select from the stored stations.
One stored station will be selected and played each time the control is
pressed. The frequency and channel number will be displayed.
NOTE: If no stations can be tuned after scanning operations, A will
appear in the display.
NOTE: If the power supply is interrupted, (fuse blows or the battery is
disconnected), the preset channels will be canceled.
6. TUNE: The TUNE control is a
multi-functional control which
works in radio and CD modes to
adjust the levels of bass, treble,
balance, fade, mid-range and
beep (off/on). Press to select
the desired function. Turn to
adjust the desired levels. TUNE
also works in radio mode to manually increase or decrease the
frequency.
DISP/ESN
2006 Tribute (j14)
Owners Guide (post-2002-fmt)
USA (fus)
Entertainment Systems
27
Page 29 of 288

14.Memory presets: Your audio is
equipped with six station
memory preset controls. These
controls can be used to select
up to six preset AM stations and 12 FM stations (six in FM1 and six
in FM2).
Select a frequency with the AM/FM.
15. SEEK/TRACK/APC: SEEK
works in radio mode and allows
you to advance to all listenable
radio stations up
or
down
the radio frequency.
Note: If you continue to press and hold the control, the frequency
will continue changing without stopping. Release the control after a
beep sounds.
TRACK: Works in CD mode and allows you to skip forward to the
beginning of the next track (
) or back to the beginning of the
current track (
).
APC (Auto program control): Works in tape mode and is not
operational on this system.
16. LOAD: Press to load a CD.
Press LOAD and a memory
preset to load a CD into a
specific slot. Press and hold
LOAD to enter up to six CDs
one at a time.
17. FM/AM: Press to enter radio
mode and select a frequency
from AM/FM1/FM2.
18. SAT: Your radio comes
equipped with Satellite ready
capability. This enables you to
view the song titles, artist, and
further information. The kit to
enable Satellite reception is
available through your dealer. Detailed Satellite instructions are
included with the dealer installed kit.
2006 Tribute (j14)
Owners Guide (post-2002-fmt)
USA (fus)
Entertainment Systems
29
Page 30 of 288

GENERAL AUDIO INFORMATION
Radio frequencies:
AM and FM frequencies are established by the Federal Communications
Commission (FCC) and the Canadian Radio and Telecommunications
Commission (CRTC). Those frequencies are:
AM - 530, 540–1700, 1710 kHz
FM- 87.7, 87.9–107.7, 107.9 MHz
Radio reception factors:
There are three factors that can affect radio reception:
•Distance/strength: The further you travel from an FM station, the
weaker the signal and the weaker the reception.
•Terrain: Hills, mountains, tall buildings, power lines, electric fences,
traffic lights and thunderstorms can interfere with your reception.
•Station overload: When you pass a broadcast tower, a stronger signal
may overtake a weaker one and play while the weak station frequency
is displayed.
Cassette/player care:
Do:
•Use only cassettes that are 90 minutes long or less.
•Tighten very loose tapes by inserting a finger or pencil into the hole
and turning the hub.
•Remove loose labels before inserting tapes.
•Allow tapes which have been subjected to extreme heat, humidity or
cold to reach a moderate temperature before playing.
•Clean the cassette player head with a cassette cleaning cartridge after
10–12 hours of play to maintain good sound/operation.
Don’t:
•Expose tapes to direct sunlight, extreme humidity, heat or cold.
•Leave tapes in the cassette player for a long time when not being
played.
2006 Tribute(j14)
Owners Guide (post-2002-fmt)
USA(fus)
Entertainment Systems
30
Page 60 of 288

CHILDPROOF DOOR LOCKS
•When these locks are set, the
rear doors cannot be opened from
the inside.
•The rear doors can be opened
from the outside when the doors
are unlocked.
The childproof locks are located on
rear edge of each rear door and
must be setseparatelyfor each
door. Setting the lock for one door
willnotautomatically set the lock
for both doors.
•Rotate lock control in the
direction of arrow to engage the
lock.
•Rotate control in the opposite
direction to disengage childproof
locks.
REMOTE ENTRY SYSTEM (IF EQUIPPED)
This device complies with part 15 of the FCC rules and with RS-210 of
Industry Canada. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device
must accept any interference received, including interference that may
cause undesired operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
The typical operating range for your remote entry transmitter is
approximately 33 feet (10 meters). A decrease in operating range could
be caused by:
•weather conditions,
•nearby radio towers,
•structures around the vehicle,
•other vehicles parked next to your vehicle, or
2006 Tribute(j14)
Owners Guide (post-2002-fmt)
USA(fus)
Locks and Security
60
Page 100 of 288

For side airbag equipped vehicles, the front passenger sensing system
will turn off the passenger seat side airbag if:
•the seat is empty and safety belt is unbuckled.
The front passenger sensing system
uses apassenger airbag offor
pass airbag offindicator which will
illuminate and stay lit to remind you
that the front passenger frontal
airbag is disabled. The indicator
lamp is located in the center stack
of the instrument panel just below
the radio.
Note: The indicator lamp will illuminate for a short period of time when
the ignition is turned to the ON position to confirm it is functional.
When the front passenger seat is not occupied (empty seat) or in the
event that the front passenger frontal airbag is enabled (may inflate), the
indicator lamp will be unlit.
The front passenger sensing system is designed to disable (will not
inflate) the front passenger’s frontal airbag when a rear facing infant
seat, a forward-facing child restraint, or a booster seat is detected.
•When the front passenger sensing system disables (will not inflate)
the front passenger frontal airbag, the indicator lamp will illuminate
and stay lit to remind you that the front passenger frontal airbag is
disabled.
•If the child restraint has been installed and the indicator lamp is not
lit, then turn the vehicle off, remove the child restraint from the
vehicle and reinstall the restraint following the child restraint
manufacturer’s instructions.
The front passenger sensing system is designed to enable (may inflate)
the front passenger’s frontal airbag anytime the system senses that a
person of adult size is sitting properly in the front passenger seat.
•When the front passenger sensing system enables the front passenger
frontal airbag (may inflate), the indicator will be unlit and stay unlit.
If a person of adult size is sitting in the front passenger’s seat, but the
passenger airbag offorpass airbag offindicator lamp is lit, it is
possible that the person isn’t sitting properly in the seat. If this happens:
•Turn the vehicle off and ask the person to place the seatback in the
full upright position.
2006 Tribute(j14)
Owners Guide (post-2002-fmt)
USA(fus)
Seating and Safety Restraints
100
Page 159 of 288

STARTING
Positions of the ignition
1. LOCK, locks the gearshift lever
and allows key removal.
2. ACCESSORY, allows the
electrical accessories such as
the radio to operate while the
engine is not running.
3. ON, all electrical circuits
operational. Warning lights
illuminated. Key position when
driving.
4. START, cranks the engine. Release the key as soon as the engine
starts.
Preparing to start your vehicle
Engine starting is controlled by the powertrain control system.
Note:This system meets all Canadian Interference-Causing Equipment
standard requirements regulating the impulse electrical field strength of
radio noise.
When starting a fuel-injected engine, avoid pressing the accelerator
before or during starting. Only use the accelerator when you have
difficulty starting the engine. For more information on starting the
vehicle, refer toStarting the enginein this chapter.
WARNING: Extended idling at high engine speeds can produce
very high temperatures in the engine and exhaust system,
creating the risk of fire or other damage.
WARNING: Do not park, idle, or drive your vehicle in dry grass
or other dry ground cover. The emission system heats up the
engine compartment and exhaust system, which can start a fire.
WARNING: Do not start your vehicle in a closed garage or in
other enclosed areas. Exhaust fumes can be toxic. Always open
the garage door before you start the engine. SeeGuarding
against exhaust fumesin this chapter for more instructions.
2006 Tribute(j14)
Owners Guide (post-2002-fmt)
USA(fus)
Driving
159