battery MERCEDES-BENZ A-CLASS HATCHBACK 2021 Owner's Manual

The
hybrid system then adapts the operating
strategy tothe fur ther course of thero ute:
R Use of electrical energy and the combustion
engine are adap ted.
R State of charge ofthe high-voltage battery is
controlled accordingl y.
R Electrical energy is reser ved especially for
electric mode, e.g. urban route sections.
R The vehicle automatically selects the operat-
ing mode.
When thero ute-based operating-mode strategy is
activated, the energy 0ow display sho ws the sta-
tus of the function as – active or passive
(/ page 299).
The route-based operating-mode strategy is
switched topassive under thefo llowing condi-
tions:
R You are driving in a drive prog ram other than
A or;.
R Route guidance is active.
R High-voltage battery's state of charge istoo
lo w. D
D
YN
YNAMIC SELECT switch AMIC SELECT switch F
F
unction of t
unction of t he D
he DYN
YNAMIC SELECT switchAMIC SELECT switch *
N
NOOTE
TE Mercedes-AMG vehicles #
Obser vethe no tes in the Supplement.
Yo u could otherwise failto recognise
dangers. %
Depending on the engine and equipment, the
ve hicle has di.erent drive prog rams.
Use theDY NAMIC SELECT switch tochange
between thefo llowing drive prog rams.
The drive prog ram selected appears in the instru-
ment displa y.
= Individual
R Individual settings
C Sport
R Continues too.er stability but with a sporty
setup
R Allo ws th e sporty driver a more active driving
style R
Driving with the combustion engine and rein-
fo rc ed boost e.ect (plug-in hybrid)
R Deactivation of the combustion engine when
stationary (plug-in hybrid)
R Only suitable for good road conditions, a dry
ro ad sur face and a clear st retch of road
A Comfort
R Comfor table and economical driving
R Balance between traction and stability
R The selection of the matching drive type by
th ehy brid system depends on the driving con-
ditions and the distance (plug-in hybrid)
R Recommended for all road conditions
Î Electric (plug-inhybrid)
R Electric mode – driving without the combus-
tion engine is possible up toappr ox.
140 km/h
R Adjustable recuperation in overrun mode
R Adaptation of Active Distance Assist
DISTRONIC for electric mode 178
178
Driving and parking

R
Depending on the equipment, the maximum
set speed for cruise control, limiter and Active
Distance Assist DISTRONIC can be limited to
th e maximum electrically drivable speed
R Activation of the combustion engine via the
pressure point of the accelerator pedal (kic k-
down)
Ï Battery Level (plug-inhybrid)
R Prioritised maintenance of the state of charge
of the high-voltage batter y,e.g. for subse-
qu ent journe ysinthe inner city/low emission
zones
R The selection of the matching drive type by
th ehy brid system depends on the driving con-
ditions and the distance
; Eco
R Only available forve hicles with automatic
transmission
R Particular lyeconomical driving
R Balance between traction and stability
R Recommended for all road conditions R
Full de velopment of all intelligent hybrid func-
tions and adap tation of the coasting charac-
te ristics of theve hicle totra1c (plug-in hybrid)
R The selection of the matching drive type by
th ehy brid system depends on the driving con-
ditions and the distance (plug-in hybrid)
% Depending on the situation, the cylinder can
be brie0y deactivated in the drive pro-
gr ams ; andA, depending on the
engine.
% The ESP ®
settings in the drive prog rams ;
and A are designed for stability. Therefore,
ch oose one of these driving prog rams, espe-
cially when transporting roof loads, in trailer
operation and when theve hicle is fully loaded
or fully occupied.
Depending on the drive prog ram, thefo llowing
systems change their characteristics:
R Drive
- engine and transmission management
- Active Distance Assist DISTRONIC
R ESP ® R
V
V ehicles wit
ehicles wit h adap
h adaptiv
tive dam
e dam ping adjus
ping adjustment tment:
:
suspension
R electric po wer steering Selects t
Selects t
he dr
he driv
ive pr
e pr ogr
ogram
am %
Depending on the equipment, theve hicle is
/tted with either a switch or a but ton. Driving and parking
179
179

#
Screw disposable hose 3onto the opening
of Ad Blue ®
re/ll canis ter4 until hand-tight. #
Screw disposable hose 3onto the /ller neck
of theve hicle until hand-tight. #
LiT up and tip AdBlue ®
re/ll canis ter4.
The /lling process stops when theAd Blue ®
ta nk is comple tely full.
Ad Blue ®
re/ll canis ter4 can be remo ved
when it has been only partial lyem ptied. #
Unscr ewand close disposable hose 3and
Ad Blue ®
re/ll canis ter4 inreve rse order. #
Replace AdBlue ®
/ller cap 2and turn it
clo ckwise until it audibly engages. #
Close fuel /ller 0ap 1.#
Switch on theve hicle for at least 60 seconds.
% Ifth eve hicle could not be star ted as the
Ad Blue ®
tank was em pty, it can take up to
60 seconds forth ere /ll tobe de tected. #
Start theve hicle.
% Avoid storing AdBlue ®
re/ll con tainers perma-
nently in theve hicle. Char
Char
ging t
ging t he high-v
he high-v olt
oltag
age batt
e batt er
ery (plug-in
y (plug-in
h
h ybr
ybr id)
id) N
No
ot
tes on c
es on c har
harging t
ging t he high-v
he high-v olt
oltag
age batt
e batt ery
ery *
N
NOOTE
TE High-voltage battery damage due to
leaving theve hicle idle for lengt hyperiods
of time Lithium-ion batteries
experience a natural self-
dischar ge.
Exhausti vedischarging can therefore occur if
th eve hicle is idle for se veral months. This can
damage the high-voltage batter y. #
Toavo id damage, please obser vethefo l-
lowing recommendations when handling
th e high-voltage batter y. *
N
NO
OTE
TE Accelerated ageing of the high-volt-
age battery As a
result of its basic characteristics, the
storage capacity of and the amount of energy
av ailable from the high-voltage battery
decrease over the course of its life. Due to th
is, bo th the maximum electrical range that
can be achie vedby theve hicle and its maxi-
mum elect rical output can be impaired.
The following factors could accelerate the age-
ing of the high-voltage batter y:
R a high le vel of charge , especially if the
ve hicle is idle for a lengt hyperiod of time
R frequent rapid charging with direct cur rent
(mode 4)
R leaving theve hicle idle for lengt hyperiods
at high ambient temp eratures #
Toavo id accelerated ageing, please
obser vethefo llowing recommendations
when handling the high-voltage batter y. Re
commendations when handling the high-voltage
batter y:
R Only charge the high-voltage battery with
direct cur rent (mode 4) if necessar y.
R If leaving theve hicle idle for lengt hyperiods,
park up theve hicle with a high- voltage battery
ch arge leve l between 25% and 30%. Do not 194
194
Driving and parking

ke
ep the high-voltage battery continuously
connected topowe r supply equipment.
R If leaving theve hicle idle for lengt hyperiods of
time avoid, if possible, high ambient temp era-
tures.
R Check the high-voltage battery's charge level
ev ery six weeks (/ page 211).
R Char gethe high-voltage battery if thech arge
le ve l is below 15%.
R Do not disconnect the 12 V battery even if the
ve hicle is leT idle for a lengt hyperiod. Other-
wise, the condition of theve hicle's high- volt-
age battery cannot be monitored.
Depending on the equipment and national ver-
sion, your vehicle is equipped with one of thefo l-
lowing vehicle soc kets:
R Type 1 forch arging with alternating cur rent
(mode 2/3)
R Type Combo 1 forch arging with alternating
cur rent (mode 2/3) and charging with direct
cur rent (mode 4)
R Type 2 forch arging with alternating cur rent
(mode 2/3) R
Type Combo 2 forch arging with alternating
cur rent (mode 2/3) and charging with direct
cur rent (mode 4) Combo 1
vehicle soc ket Combo 2
vehicle soc ket
1 Type 1 or type 2 connection forch arging with
alternating cur rent
2 Socketex tension forch arging with direct cur-
re nt Driving and parking
195
195

%
When using a CCS (Combined Charging Sys-
te m) charging cable tocharge with direct cur-
re nt at a combo vehicle soc ket, bo thvehicle
soc ket connections 1and 2are used for
ch arging.
Charging options forth e high-voltage battery
(mode 2, 3 or 4):
R Charging through recuperation while theve hi-
cle is in motion
R Charging with alternating cur rent when sta-
tiona ry:
- at a mains soc ket (mode 2)
- at a wallbox or charging station (mode 3)
R Charging with direct cur rent when stationary
(vehicles with combo vehicle soc kets):
- at a fast charging station (mode 4)
Depending on the count ry-speci/c vehicle equip-
ment and your vehicle's charging cable, single
phase ACcharging is also possible.
Obser vethe di.erent grid requ irements of your
cur rent location when charging. Only use charging
cables which conform tothegr id requiremen ts.Consult a
quali/ed elect rician or your local grid
operator if you ha veany questions.
It is recommended that youch arge the high-volt-
age battery at a wallbox or charging station due to
th e impr ovedch arging per form ance and better
ch arging e1ciency o.ered.
S
S t
to
o wing t
wing t he c
he char
harging cable
ging cable
Alw ays st owtheve hicle charging cable in the
ch arging cable bag pr ovided and secure it in the
boot or load compartment of your vehicle.
Otherwise, thech arging cable is not su1ciently
secured.
Syst Syst em limits
em limits
The po wer output of the high-voltage battery may
be impaired bythefo llowing:
R High or low outside temp eratures
R Electrical auxiliary consumers in theve hicle
being switched on, e.g. operating the air con-
ditioning system
R Extended periods without charging The
charging time of the high-voltage battery may
be increased bythefo llowing:
R High or low outside tempe ratures
R Extended periods without charging
R The maximum available charge cur rent of the
ch arging facility
R The charging cur rent set (mode 2) in the multi-
media system (/ page 298) N
No
ot
tes on c
es on c har
harging t
ging t he high-v
he high-v olt
oltag
age batt
e batt er
ery at t
y at t he
he
mains soc ke
mains soc ket (mode 2)
t (mode 2) &
D
DAN
AN GER
GER Risk of fatal injury from incor-
re ctly ins talled component parts
Connecting thech arging cable toa mains
soc ket using incor rectly ins talled component
parts could cause a /re or an electric shoc k,
fo rex ample. #
Only connect thech arging cable to a
mains soc ketth at:
R Has been proper lyinstalled and 196
196
Driving and parking

R
Has been inspec tedby aqu ali/ed elect ri-
cian #
For saf etyre asons, only use thech arging
cable supplied with theve hicle or an
original Mercedes-Benz charging cable. #
Purchase these parts at a Mercedes-
Benz Service Centre and obtain advice
th ere.
Mercedes-Benz thoroughly tests these original
ch arging cables forth eir suitability for high-
vo ltage charging of your vehicle. #
Never use a damaged charging cable. #
Do not use:
R Extension cables
R Extension reels
R Multiple soc kets #
Never use soc ket ada pters toconnect
th ech arging cable tothe mains soc ket.
The only exception being if the adap ter
has been tested and appro vedby the manufacturer
forch arging the high-volt-
age battery of an electric vehicle. #
Obser vethe saf ety no tes in the operat-
ing inst ructions forth e soc ket ada pter. Only
thefo llowing charging cables may be used:
R The charging cable supplied with theve hicle.
R Ach arging cable that has been appr ovedfor
th eve hicle.
The charging process can vary depending on the
po we r supply equipment.
Shor terch arging times can be achie ved in thefo l-
lowing ways:
R Charging at a wallbox.
R Charging at a charging station.
When doing so, alw ays obser vethe local informa-
tion.
Do not lea vethech arging cable cont rols hanging
loose from a mains soc ket. Do not liT
the controls bythefo llowing compo-
nent parts:
R The charging cable connector.
R The mains plug.
When charging, pr otect thech arging cable cont rol
element from excessive heat such as direct sun-
light. Otherwise, thech arging process may be
cancelled. N No
ot
tes on c
es on c har
harging t
ging t he high-v
he high-v olt
oltag
age batt
e batt er
ery at a
y at a
w
w allbo
allbo x or c
x or c har
har ging st
ging st ation (mode 3)
ation (mode 3) &
D
DAN
AN GER
GER Risk of fatal injury from incor-
re ctly ins talled component parts
Connecting thech arging cable toawa llbox
using incor rectly ins talled component parts
could cause a /re or an electric shoc k,for
ex ample. #
Only connect thech arging cable to a
wa llbox that:
R Has been proper lyinstalled and Driving and parking
197
197

R
Has been inspec tedby aqu ali/ed elect ri-
cian #
For saf etyre asons, only use charging
cables that ha vebeen tested and
appro vedby the manufacturer forch arg-
ing the high-voltage battery in an electric
ve hicle. #
Never use damaged charging cables. #
Do not extend thech arging cable. #
Do not use adap ters. #
Obser vethe saf ety no tes in the operat-
ing inst ructions forth ewa llbox. If
ch arging at a wallbox without pre-ins talled
cable, use the optionally available charging cable
fo rwa llbox and charging station (mode 3). The
ch arging cable is st owed in a bag in the boot/
luggage compartment.
Only use charging cables that ha vebeen tested
and appro vedby the manufacturer forch arging
th e high-voltage battery in an electric vehicle. &
D DAN
AN GER
GER Risk of fatal injuries due todam-
aged components
Connecting thech arging cable toach arging
station using a damaged component part
could cause a /re or an elect ric shoc k,for
ex ample. #
Forch arging stations with a preinstalled
ch arging cable:
R Perform a visual check of thech arg-
ing station for obvious faults, such as
massive damage tothe housing or
ch arging cable. #
Forch arging stations without a preinstal-
led charging cable:
R For saf etyre asons, only use charging
cables that ha vebeen tested and
appro vedby the manufacturer for
ch arging the high-voltage battery in
an electric vehicle.
R Never use damaged charging cables.
R Do not extend thech arging cable.
R Do not use adap ters. #
Make sure toobser vethe saf ety in form a-
tion on thech arging station. Most
charging stations must be activated before
th ech arging process, e.g. using an RFID card.
Obser vethe on-site operator's inst ructions forthe
ch arging station.
The amount of ene rgy dispensed forth ech arging
process, shown bythech arging station, may be
higher than the amount of energy actually absor-
bed bythe high-voltage batter y.This is there sult
of di.erent le vels of charging losses and is descri-
bed as rech arge e1ciency. Charging losses occur,
fo rex ample, due toheat that builds up when
ch arging or from auxiliary consumers that are
switched on. Further information on rech arge e1-
ciency can be obtained at a quali/ed specialist
wo rkshop. 198
198
Driving and parking

N
N
o
ot
tes on c
es on c har
harging t
ging t he high-v
he high-v olt
olt ag
age batt
e batt er
ery at a
y at a
f
f as
ast c t c har
har ging st
ging st ation (mode 4)
ation (mode 4) &
D
D AN
AN GER
GER Risk of fatal injuries due todam-
aged components
Connecting thech arging cable toach arging
station using a damaged component part
could cause a /re or an elect ric shoc k,for
ex ample. #
Forch arging stations with a preinstalled
ch arging cable:
R Perform a visual check of thech arg-
ing station for obvious faults, such as
massive damage tothe housing or
ch arging cable. #
Forch arging stations without a preinstal-
led charging cable:
R For saf etyre asons, only use charging
cables that ha vebeen tested and
appro vedby the manufacturer for
ch arging the high-voltage battery in
an electric vehicle.
R Never use damaged charging cables.
R Do not extend thech arging cable. R
Do not use adap ters. #
Make sure toobser vethe saf ety in form a-
tion on thech arging station. Most
charging stations must be activated before
th ech arging process, e.g. using an RFID card.
Obser vethe on-site operator's inst ructions forthe
ch arging station.
The charging cable forth eve hicle must not be
lon gerth an 30 m due tothe legal requ irements in
some countries. This is toprev ent the inter fer-
ence of signals being received byradio communi-
cation devices in theve hicle or in close pr oximity
to thech arging station. Be awarethat parts of the
ch arging cable may be routed under ground. If in
doubt, ask thech arging station operator if this is
th e case before charging the high-voltage batter y.
The amount of energy dispensed forth ech arging
process, shown bythech arging station, may be
higher than the amount of energy actually absor-
bed bythe high-voltage batter y.This is there sult
of di.erent le vels of charging losses and is descri-
bed as rech arge e1ciency. Charging losses occur,
fo rex ample, due toheat that builds up when ch
arging or from auxiliary consumers that are
switched on. Further information on rech arge e1-
ciency can be obtained at a quali/ed specialist
wo rkshop. Se
Se
tting t
tting t he maximum per
he maximum per missible c
missible char
harging cur-
ging cur-
r
r ent f
ent f or c
or char
harging at a mains soc ket
ging at a mains soc ket *
N
NO
OTE
TE Overloading the mains soc ket due
to excessive charging cur rent If
th ech arging cur rent is too high, the fuse
could be tripped or theex tern al mains supply
could overheat. #
Make sure that theex tern al mains supply
has been designed tohandle the set
ch arging cur rent. #
If necessar y,reduce the set charging
cur rent or use a di.erent mains soc ket. #
For saf etyre asons, only use thech arging
cable supplied with theve hicle or an
original Mercedes-Benz charging cable.
Mercedes-Benz thoroughly tests these
original charging cables forth eir suitabil- Driving and parking
199
199

Combo 2
vehicle soc ket #
Press the centre rear section of soc ket 0ap
1 and swing the soc ket 0ap forw ards and
open.
The % indicator lamp 2and status dis-
play 3light up white. %
When theve hicle is switched on (the õ
displ ayis lit in the Instrument Display), soc ket
0ap 1cannot be opened. #
Press cat ch7 tothe leT and fold open
soc ket co ver5.
% Vehicles with a vehicle soc ket combo requ ire
only connection 8forth ech arging cable
connector. Open only the upper part of soc ket
co ver5. #
Tocharge at a mains soc ket, insert the mains
plug into the mains soc ket of theex tern al
po we r source tothe stop and set the maxi-
mum charging cur rent if requ ired
(/ page 199). #
Insert thech arging cable connector into vehi-
cle soc ket connection 8tothe stop. If the
wa llbox/charging station is not equipped with
a ch arging cable, inse rtthe plug of theve hi-
cle's charging cable into thewa llbox/charging
station soc ketto the stop.
Make sure that thech arging cable is not taut
when inser ted. The
# indicator lamp 4and status dis-
play 30ash orange and, as soon as the high-
vo ltage battery is charge d, green.
When thech arging cable is connected totheve hi-
cle, theve hicle cann otbe star ted or mo ved.
At the start of thech arging process, thech arge
le ve l display is shown in the Instrument Display
with a charging prediction. The charging predic-
tion either refers to the predicted charge leve l at
th e set departure time, or the time at which the
high- voltage battery will be fully charge d.
% Depending on thete mp erature, thefa n and
bat tery cooling system may audibly switch on
during thech arging process.
% Ifth eve hicle is idle for lengt hyperiods and
connected tothe mains suppl y,the high-volt-
age battery will be rech arge d automatically as
needed or when electrical consumers are
activated (e.g. the pre-entry climate control). Driving and parking
205 205

Combo 1
vehicle soc ket Combo 2
vehicle soc ket #
Press the centre rear section of soc ket 0ap
1 and swing the soc ket 0ap forw ards and
open.
The % indicator lamp 2and status dis-
play 3light up white. %
When theve hicle is switched on (the õ
displ ayis lit in the Instrument Display), soc ket
0ap 1cannot be opened. #
Press cat ch7 tothe leT and fold open
soc ket co ver5.
% The CCS charging cable connector requ ires
connections 6and 8. Therefore, it is nec-
essary toopen bo thparts of soc ket co ver5. #
Insert the CCS charging cable connector into
th eve hicle soc ketto the stop.
Make sure that thech arging cable is not taut
when inser ted.
The # indicator lamp 4and status dis-
play 30ash orange and, as soon as the high-
vo ltage battery is charge d, green.
When thech arging cable is connected totheve hi-
cle, theve hicle cann otbe star ted or mo ved.
At the start of thech arging process, thech arge
le ve l display is shown in the Instrument Display
with a charging prediction. The charging predic-
tion either refers to the predicted charge leve l at
th e set departure time, or the time at which the
high- voltage battery will be fully charge d. Driving and parking
209 209