diagram MERCEDES-BENZ C CLASS 2016 Owners Manual

cycle racks or overhanging loads. Following a
severe impact or in the event of damage to the
bumpers, have the function of the radar sensors
checked at a qualified specialist workshop.
Blind Spot Assist may no longer work properly.
Monitoring area In particular, the detection of obstacles can be
impaired if: R
there is dirt on the sensors or anything else
covering the sensors R
there is poor visibility, e.g. due to fog, heavy
rain, snow or spray R
there are narrow vehicles, e.g. motorcycles or
bicycles R
the road has very wide lanes R
the road has narrow lanes R
you are not driving in the middle of the lane R
there are barriers or similar lane borders
Vehicles in the monitoring range are then not
indicated.
Blind Spot Assist monitors the area up to 10 ft
(3 m) behind your vehicle and directly next to
your vehicle, as shown in the diagram.
If the lanes are narrow, vehicles driving in the
lane beyond the lane next to your vehicle may be
indicated, especially if the vehicles are not driv-
ing in the middle of their lane. This may be the
case if there are vehicles driving at the inner
edge of their lanes. Due to the nature of the system: R
warnings may be issued in error when driving
close to crash barriers or similar solid lane
borders. R
the warning is canceled when driving for an
extended period next to long vehicles, such as
trucks.
Warning display
C
Warning display
Blind Spot Assist is not active at speeds below
approximately 20 mph (30 km/h). Vehicles in
the monitoring range are then not indicated.
If a vehicle is detected within the blind spot
monitoring range at speeds above 20 mph
(30 km/h), warning lamp C on the correspond-
ing side lights up red. This warning is always
emitted when a vehicle enters the blind spot
monitoring range from behind or from the side.
When you overtake a vehicle, the warning only
occurs if the difference in speed is less than
7 mph (12 km/h).
If you select the reverse gear, Blind Spot Assist
is not operational.
The brightness of the warning lamps is auto-
matically adapted to the brightness of the sur-
roundings.
Collision warning
If a vehicle is detected in the monitoring range of
Blind Spot Assist and you switch on the corre-
sponding turn signal, a double warning tone
sounds. Red warning lamp C flashes. If the turn
signal remains on, vehicles detected are indica-
ted by the flashing of red warning lamp C .
There are no further warning tones.Driving systems 217
Driving and parking Z

you then switch on th e correspondin g tur n sig-
nal to chang e lane, you will also receiv e an opti-
cal and audibl e warning. If a ris k of lateral colli-
sion is detected, corrective brakin g may help
you avoid a collision . Befor e a course-correcting
brak e application , Active Blind Spot Assis t eval -
uates th e spac e in th e direction of travel and at
th e side s of th e vehicle. Fo r this, Active Blind
Spot Assis t uses th e forward-facing rada r sen -
sors.
Active Blind Spot Assis t support s you from a
speed of approximately 20 mph (30 km/h).
Important safety notes Active Blind Spot Assis t is only an aid and is no t
a substitut e for attentive driving.
G WARNIN G
Active Blind Spot Assis t does no t reac t to :R
vehicles overtake n to o closely on th e side ,
placin g them in th e blin d spo t areaR
vehicles whic h approac h wit h a larg e speed
differential and overtake your vehicl e
As a result , Active Blind Spot Assis t may nei-
ther giv e warnings no r interven e in suc h sit -
uations. There is a ris k of an accident.
Always observ e th e traffic condition s care-
fully, and maintai n a saf e lateral distance.
i US A only: This device has been approve d by
th e FCC as a "Vehicular Radar System". The
rada r sensor is intended for use in an auto-
motive rada r system only. Removal, tamper -
ing, or altering of th e device will voi d any war-
ranties, and is no t permitte d by th e FCC. Do
no t tamper with, alter, or use in any non-
approve d way.
An y unauthorize d modification to this device
could voi d th e user's authorit y to operate th e
equipment.
i Canada only: This device complies wit h
RSS-210 of Industry Canada. Operation is
subjec t to th e followin g tw o conditions:
1. This device may no t caus e harmful inter-
ference , and
2. This device mus t accept any interferenc e
received, includin g interferenc e that may
caus e undesir ed o peration of th e d
evice .
Removal, tampering, or altering of th e device
will voi d any warranties, and is no t permitted. Do no t tamper with, alter, or use in any non-
approve d way.
An y unauthorize d modification to this device
could voi d th e user's authorit y to operate th e
equipment.
Rada r sensor sThe Active Blind Spot Assis t rada r sensor s are
integrate d into th e fron t and rear bumpers and
behind a cover in th e radiato r trim. Mak e sur e
that th e bumpers and th e cover in th e radiato r
grill are free of dirt, ice or slush. The rear sensor s
mus t no t be covered, e.g. by bicycle racks or
overhangin g loads . Following a severe impact or
in th e event of damage to th e bumpers , hav e th e
function of th e rada r sensor s checke d at a quali-
fie d specialist workshop . Active Blind Spot
Assis t may otherwise no longer wor k properly.
Monitoring area
G WARNIN G
Active Blind Spot Assis t does no t detec t all
traffic situation s and roa d users. There is a
ris k of an accident.
Always mak e sur e that there is sufficien t dis-
tance on th e side for other traffic or obstacles.
Active Blind Spot Assis t monitors th e area up to
10 ft (3. 0 m) behind your vehicl e and directl y
next to your vehicle, as shown in th e diagram.220
Driving systems
Driving and parking