deactivate passenger airbag MERCEDES-BENZ C-CLASS CABRIOLET 2016 Owners Manual

Basic illustration
X Adjust the seat (Y page 100).
The seat backrest must be in an almost ver-
tical position.
X Pull the seat belt smoothly out of seat-belt
extender =and engage belt tongue ;into
belt buckle :.
The seat belt on the driver's seat and the
front-passenger seat may be tightened auto-
matically; see "Belt adjustment"
(Y page 47).
X If necessary, pull upwards on the seat belt in
front of your chest so that the belt sits tightly
across your body.
Releasing seat belts !
Make sure that the seat belt is fully rolled up.
Otherwise, the seat belt or belt tongue will be
trapped in the door or in the seat mechanism. This could damage the door, the door trim
panel and the seat belt. Damaged seat belts
can no longer fulfil their protective function
and must be replaced. Visit a qualified spe-
cialist workshop.
X Press release button in belt buckle, hold belt
tongue firmly and guide the seat belt back.
Seat belt adjustment The seat-belt adjustment is an integral part of
the PRE-SAFE ®
convenience function. This func-
tion adjusts the driver's and front-passenger
seat belt to the upper body of the occupants. The belt strap is tightened slightly when:
R the seat belt tongue is engaged in the belt
buckle and
R the ignition is switched on
The seat-belt adjustment will apply a certain
tightening force if any slack is detected between
the vehicle occupant and the seat belt. Do not
hold on to the seat belt tightly while it is adjust-
ing.
You can activate and deactivate the seat-belt
adjustment function using the multimedia sys-
tem. Information on activating and deactivating
the seat-belt adjustment function can be found
in the Digital Owner's Manual.
Belt warning for the driver and front
passenger The
7 seat belt warning lamp in the instru-
ment cluster reminds you that all vehicle occu-
pants must fasten their seat belts. It may light up
continuously or flash. A warning tone may also
sound.
The 7 seat belt warning lamp goes out and
the warning tone stops as soon as the driver's
and the co-driver's seat belts have been fas-
tened.
Rear seat belt status indicator The rear seat belt status indicator is available
only in certain countries.
The rear seat belt status indicator informs you
which rear seat belt is not fastened.
Cancelling the rear seat belt status indicator
immediately (Y page 241). Airbags
Introduction The airbag installation location is identified by
the label AIRBAG. Occupant safety
47Safety Z

Vehicles without automatic co-driver's
front airbag deactivation system If the co-driver's seat of your vehicle is not
equipped with an automatic co-driver's front air-
bag deactivation system, this is indicated by a
special sticker. The sticker is affixed to the side of the dashboard on the co-driver's side. The
sticker is visible when you open the co-driver's
door.
Never fit a rearward-facing child restraint sys-
tem to the co-driver's seat in this case
(Y page 62).
Observe the following information under "Rear-
ward-facing child restraint system"
(Y page 62) and "Forward-facing child
restraint system" (Y page 62) and on suitable
positioning of the child restraint system
(Y page 62).
Rearward-facing child restraint system If it is absolutely necessary to fit a rearward-
facing child restraint system to the co-driver's
seat, you must always make sure that the co-
driver's front airbag is deactivated. The co-driv-
er's front airbag is only disabled if the
PASSENGER AIRBAG OFF indicator lamp is lit
continuously (Y page 43).
Always observe the information about suitable
positioning of the child restraint system
(Y page 62) as well as the child restraint sys-
tem manufacturer's installation and operating
instructions.
Forward-facing child restraint system If it is absolutely necessary to secure a child in a
forward-facing child restraint system on the co- driver's seat, you must always move the co-driv-
er's seat as far back as possible. Fully retract the
seat cushion length. The base of the child restraint system must lie fully on the co-driver's
seat cushion. The backrest of the child restraint
system must lie as flat against the co-driver's
seat backrest as possible. The child restraint
system may not touch the roof or be put under
strain by the head restraint. Adjust the angle of
the seat backrest and the head restraint posi-
tion accordingly. Always make sure that the
shoulder belt strap is correctly routed from the
vehicle belt sash guide to the shoulder belt
guide on the child restraint system. The shoul-
der belt strap must be routed forwards and
downwards from the vehicle belt outlet. If nec-
essary, adjust the vehicle belt sash guide and
the co-driver's seat accordingly.
Always observe the information about suitable
positioning of the child restraint system
(Y page 62) as well as the child restraint sys-
tem manufacturer's installation and operating
instructions. Suitable positioning of the child
restraint system
Introduction Only child restraint systems that are approved in
accordance with ECE standard ECE R44 are per-
mitted for use in the vehicle.
"Universal"-category child restraint systems can be recognised by their orange approval label and
the text "Universal". Example: approval label on the child restraint
system
The following "Universal"-category child
restraint systems can be used on seats labelled
U, UF or IUF according to the tables "Suitability
of the seats for attaching a belt-secured child
restraint system" or "Suitability of the seats for
attaching an ISOFIX child restraint system". 62
Children in the vehicleSafety