engine coolant MERCEDES-BENZ C-Class COUPE 2017 CL205 User Guide

Warning/
indicator
lampNSignal type
Possiblec auses/consequences and M
Solutions
XAt coolant temperatures below 248 ‡(120 †), drive to the neares tqualified
specialist workshop.
XAvoid heavy loads on the engine as you do so, e.g. driving in mountainous terrain
and stop-and-go traffic.
Driving systems
Warning/
indicator
lampNSignal type
Possiblec auses/consequences and M
Solutions
·NThe red distance warning lamp lights up while the vehicleisinm otion.Awarning
tone als osounds.
You are approaching avehicle, apedestrian or astationary obstacl einyourline of
travel at too high aspeed.
XBe prepared to brake immediately.
XPay carefu lattention to the traffic situation. You may have to brake or take
evasive action.
Further information on PRE ‑SAFE
®Brake (Ypage70).
For further information about the distance warning function of COLLISION PRE-
VENTION ASSIST PLUS, see (
Ypag e64).
Warning and indicator lamps in the instrument cluster255
On-board computer and displays
Z

Checking theoil level usin gthe oil dip-
stick
Example
XPull oil dipstick :out of th edipstick guide
tube.
XWipe off oil dipstick :.
XSlowly slide dipstick :intothe guide tub eto
th es top, and tak eitout again after approx-
imately 3seconds.
If th elevelisb etween MIN mark =and MAX
mark ;,theoil leve liscorrect.
XIf theoil leve lhas dropped to MIN mark =or
below, add 1. 1USqt(1.0l iter) of engineo il.
Adding engine oil
HEnvironmental note
When addingo il, takecaren otto spill any. If
oil enters th esoil or waterways, it is harmful to
th ee nvironment.
!Only use engineo ils and oil filters that have
been approved for vehicle swithas ervicesys-
tem. You can obtain alist of th eengineo ils
and oil filters tested and approved in accord- anc ewitht heMercedes-Ben zSpecifications
for Servic eProduct satany Mercedes-Benz
Servic ecenter.
Damage to th eengineore xhaust system is
caused by th efollowing:
Rusinge ngineo ils and oil filters that have not
been specifically approved for th eservice
system
Rreplacin gengineo il and oil filters after the
interval for replacements pecifiedbythe
servic esystem has been exceeded
Rusinge ngineo il additives.
!Do no tadd to omucho il. addingt oomuch
engineo il can result in damagetot heengine
or to th ecatalyti cconverter. Hav eexcess
engineo il siphoned off.
Example
XTurn cap :counter-clockwise and remove it.
XAdde ngineo il.
If th eoil leve lisatorb elow theMIN mar kon
th eo il dipstick ,add 1. 1USq t(1.0 l)of engine
oil.
XReplace cap :on the filler neck and turn
clockwise.
Ensure that the cap locks into place securely.
XCheck the oil level again with the oil dipstick
(Ypage 289).
Further information on engine oil (
Ypage 346).
Additional service products
Important safety notes
GWARNING
Certain components in the engine compart-
ment,s uch as the engine, radiator and parts
of the exhaust system, can become very hot.
Working in the engine compartment poses a
risk of injury.
Where possible, let the engine cool down and touch only the components described in the
following.
GWARNING
The cooling system is pressurized, particularly
when the motor is warm. If you open the cap,
you could be scalded if hot coolant sprays out.
There is arisk of injury.
Engine compartment289
Maintenance and care
Z

Let the engine cool down before you open the
cap. Wear gloves and eye protection. Slowly
open the cap to relieve pressure.
GWARNING
Windshield washer concentrate could ignite if it comes into contact with hot engine compo-
nents or the exhaust system. There is arisk of
fire and injury.
Make sure that no windshield washer con-
centrate is spilled next to the fillern eck.
Checking coolant level
XPark the vehicle onalevel surface.
Only check the coolant level when the vehicle
is on alevel surface and the engine has cooled
down.
XTurn the SmartKey to position 2in the ignition
lock (Ypage 131).
or
XOn vehiclesw ith KEYLESS-GO, press the
Start/Stop button twice (Ypage 131).
XCheck the coolant temperature display in the
instrument cluster (Ypage 201).
The coolant temperature must be below
158 ‡(70 †).
XTurn the SmartKey to position 0in the ignition
lock (Ypage 131).
or
XOn vehiclesw ith KEYLESS-GO, pul lthe Start/
Stop button from the ignition lock
(
Ypage 131).
XSlowl yturn cap :half aturn counter-clock-
wise to allow excess pressure to escape.
XTurn cap :further counter-clockwise and
remove it.
If the coolant is at the level of marker bar =
in the fillern eck when cold, there is enough
coolant in coolant expansio ntank ;.
If the coolant level is approximately 0.6 in
(1.5 cm) above marker bar =in the fillern eck
when warm, there is enough coolant in expan-
sion tank ;.
XIf necessary ,add coolant that has been tested
and approved by Mercedes-Benz.
XReplace cap :and turn it clockwise as far as
it wil lgo.
For further information on coolant, see
(
Ypage 347).
Adding washe rfluid to the windshield
washe rsystem
XTo open: pullcap : upwards by the tab and
open.
XAdd the premixed washer fluid.
XTo close: press cap :onto the fillern eck
until it engages.
If the washer flui dlevel drops belowt he recom-
mended minimum of 1liter, amessag eappears
in the multifunction display prompting you to
add washer flui d(
Ypage 245).
Further information on windshield washer fluid/
antifreeze (
Ypage 348).
ASSYST PLUS
Servic emessage
The ASSYST PLUS service interval display
informs you of the next service due date.
290ASSYST PLUS
Maintenancea nd care

from the data shownhere. You can find the
data applicable to you rvehicleont he vehicle
identificatio nplate.
Vehicle identification number (VIN)
XSlid ethe right-hand front seattoi ts rearmost
position.
XFold floor covering ;upwards.
The VIN is visible :.
The VIN can als obefound on the vehicl eiden-
tification plate (
Ypag e343).
The VIN can als obefound at the lower edge of
the windshield (
Ypag e344).
Engine number
:Engine numbe r(stamped into the crank-
case)
;VIN (on the lower edge of the windshield)
=Emissio ncontrol information plate, includ-
ing the certification of both federala nd Cali-
fornia nemissions standards
Service products and filling capaci-
ties
Important safety notes
GWARNING
Service products may be poisonousa nd haz-
ardous to health. There is arisk of injury.
Comply with instructions on the use ,storage
and disposal of service products on the labels
of the respective original containers. Always
store service products sealed in their original
containers. Always keep service products out
of the reach of children.
HEnvironmental note
Dispos eofservice products in an environ-
mentall yresponsiblem anner.
Service products include the following:
RFuels
RLubricants (e.g. engine oil ,transmission oil)
RCoolant
RBrake fluid
RWindshiel dwasher fluid
RClimate control syste mrefrigerant
Components and service products must match.
Only use products recommendedbyM ercedes-
Benz. Damag ewhich is caused by the use of
products which have not been recommendedi s
not covered by the Mercedes-Benz warranty or
goodwil lgestures. They are listed in this
Mercedes-Benz Operator's Manual in the appro- priate section.
Informatio nontested and approved products
can be obtained at an authorized Mercedes-
Benz Center or on the Internet at
http://bevo.mercedes-benz.com.
You can recognize service products approved by
Mercedes-Benz by the following inscription on
the containers:
RMB-Freigabe (e.g. MB-Freigabe 229.51)
RMB-Approval( e.g. MB-Approval2 29.51)
Other designations or recommendations indi-
cate alevelofq uality or aspecificatio nin
accordance with an MB Sheet Number (e.g. MB
229.5). They have not necessarily been
approved by Mercedes-Benz.
344Service products and filling capacities
Technical data

Filling capacities
The followingvalue srefer to an oil chang e
includin gthe oil filter.
Missing value swere no tavailable at time of
goin gtop rint.
ModelCapacit y
Mercedes ‑AMG
vehicles
C3 007.4USq t(7.0 l)
C300 4MATIC6.9 US qt (6.5 l)
Additives
!Do not us eany additive sinthe engine oil.
Thi scould damag ethe engine.
Brake fluid
GWARNING
The brake fluid constantly absorb smoisture
from the air. Thi slowers the boiling point of
the brake fluid .Ifthe boiling point of the brake
fluid is too low, vapor pockets may form in the
brake system when the brakes are applied
hard. Thi swould impai rbraking efficiency.
There is ariskofana ccident.
Yo us houl dhavet he brake fluid renewe dat
the specified intervals.
Whe nhandling brake fluid ,observe the impor-
tant safety notes on service products
(
Ypage 344).
The brake fluid change interval scan be found in
the Maintenance Booklet.
Only us ebrake fluid approved by Mercedes-
Benz in accordance with MB-Freigab eorMB-
Approva l331.0.
Information abouta pproved brake fluid can be
obtaine datany qualified specialist workshopo r
on the Interne tat
http://bevo.mercedes-benz.co m.
iHave the brake fluid regularly replaced at a
qualified specialist workshop in accordance
with the replacement intervals and the
replacement confirmed in the Maintenance
Booklet.
Coolant
Importan tsafety notes
GWARNING
If antifreeze comes into contact with hot com- ponents in the engine compartment, it may
ignite. There is arisk of fire and injury.
Let the engine cool dow nbefore yo uadd anti-
freeze .Make sur ethat antifreeze is not spilled
next to the filler neck. Thoroughly clea nthe
antifreeze from components before starting
the engine.
!Only ad dcoolant that has bee npremixed
with the desire dantifreeze protection. You
coul dotherwise damag ethe engine.
Furthe rinformatio noncoolants can be found
in the Mercedes-Benz Specifications for Ser-
vice Products, MB BeVo 310.1, e.g. on the
Internet at http://bevo.mercedes-benz.com.
Or contact aqualifie dspecialist workshop.
!Always use asuitabl ecoolant mixture, even
in countries where hig htemperatures prevail.
Otherwise ,the engine cooling system is not
sufficiently protected from corrosion and
overheating.
iHave the coolant regularly replaced at a
qualified specialist workshop and the replace-
ment confirmed in the Maintenance Booklet.
Comply with the important safety notes for ser-
vice products whe nhandling coolant
(
Ypage 344).
The coolant is amixture of water and anti-
freeze/corrosion inhibitor. It performs the fol-
lowing tasks:
RAnti-corrosion protection
RAntifreeze protection
RRaising the boiling point
If the coolant has antifreeze protection dow nto
-35 ‡(-37† ), the boiling point of the coolant
during operation is approximatel y266 ‡
(130 †).
Service products and filling capacities347
Technical data
Z

The antifreeze concentrate/corrosion inhibitor
concentration in the engine cooling system
should:
Rbe at least 50%. This will protectthe engine
cooling system against freezin gdown to
approximately -35 ‡(-37 †).
Rnot exceed 55% (antifreez eprotection down
to -49 ‡[-45 †]) .Otherwise, hea twilln ot be
dissipated as effectively.
Mercedes-Benz recommends an antifreeze/
corrosion inhibito rconcentrate in accordance
with MB Specifications for Service Products
310.1.
iWhe nthe vehicl eisfirst delivered, it is filled
with acoolant mixture thate nsures adequate
antifreeze and anti-corrosion protection.
iThe coolant is checked with every mainte-
nance intervalataq ualified specialist work-
shop.
Fillin gcapacities
ModelCapacity
Mercedes ‑AMG
vehicles12.6 US qt (11.9 l)
Allo ther models9.5 US qt (9.0 l)
Windshield washe rsystem
Important safety notes
GWARNING
Windshiel dwasher concentrate coul dignite if
it comes into contact with hot engine compo-
nents or the exhaust system. There is arisk of
fire and injury.
Make sure that no windshield washer con-
centrate is spilled next to the filler neck.
!Only use washer flui dthat is suitabl efor
plastic lam plenses, e.g. MB SummerFi torMB
WinterFit. Unsuitabl ewasher flui dcoul ddam-
age the plastic lense softhe headlamps.
!Only MB SummerFi tand MB WinterFit
washer flui dshould be mixed together. The
sprayn ozzles may otherwise become
blocked. Do not use distille
dorde-ionized water, other-
wise, the leve lsensor may give afals ereading.
When handling washer fluid, observe the impor-
tant safety notes on service products
(
Ypag e344).
At temperatures above freezing:
XFill the washer flui dreservoir with amixture of
water and windshield washer fluid, e.g. MB
SummerFit.
Add 1part MB SummerFi tto100 parts water.
At temperatures below freezing:
XFill the washer flui dreservoir with amixture of
water and washer fluid, e.g. MB WinterFit.
For the correct mixing ratio refer to the infor-
mation on the antifreeze reservoir.
iAdd windshield washer fluid, e.g. MB Sum-
merFit or MB WinterFit, to the washer flui dall
yea rround.
Climate control systemr efrigerant
Important safety notes
The climate control syste mofyourvehicleisf il-
led with refrigerant R ‑134a.
The instructio nlabel regarding the refrigerant
type use dcan be found on the radiator cross
member.
!Only the refrigerant R ‑134a and the PAG oil
approved by Mercedes-Benz may be used.
The approved PAG oil may not be mixed with
any other PAG oil that is not approved for
R-134a refrigerant. Otherwise, the climate
control syste mmay be damaged.
Service work, such as refilling with refrigerant or
replacing component parts, may only be carried
out by aqualified specialist workshop. All appli-
cabl eregulations, as wel lasSAE standard J639,
must be adhered to.
Always have work on the climate control system
carrie dout at aqualified specialist workshop.
348Service products and filling capacities
Technical data