start stop button MERCEDES-BENZ C-Class COUPE 2017 CL205 Owner's Guide

not be switched off automaticallywhenthe vehi-
cle stops.
The ECO start/stopf unctionisd eactivated, if:
Ryous witch to drive program RACE
(S‑MO DEL),S+orS(Ypage 139)
Ryo up ermanentlya ctivate manua lgearshifting
(Ypage 146)
If yo uhavep ermanentlya ctivatedmanual gear-
shifting and then press ECO button :,the ECO
start/stopf unctionisa ctivated.
AM Gsports exhausts ystem
(Mercedes AM Gvehicles)
Youc an choose between different AMG sports
exhaus tsystem volumes using the positio nof
the exhaus tflap.
Each time yo ustart the engine with the Smart-
Key or the Start/Stop button, the quietest set-
ting is activated.
Setting the volume:
XPress button :.
If yo uselect the loudest setting, indicator
lamp lights up ;.
Yo uc an also adjus tthe positio nofthe exhaust
fla pu sing the:
RDYNAMIC SELECTs witch (Ypage 139)
Rmultimedia system
Driving137
Driving an dparking
Z

Problems with the engine
ProblemPossible causes/consequences andMSolutions
The engine does not
start. The starter motor
can be heard.RThere isamalfunction in the engine electronics.
RThere is amalfunction in the fuel supply.
Before attempting to start the engine again:
XTurn the SmartKey back to position 0in the ignition lock.
or
XPress the Start/Stop button repeatedly until all indicator lamps in
the instrumentc luster go out.
XTry to start the engine again (Ypage 133). Avoid excessively long
and frequent attemptstos tart the engine as these will drain the
battery.
If the engine does not start after several attempts:
XConsult aqualified specialist workshop.
The engine does not
start. You cannot hear
the starter motor.The on-board voltage is too low because the battery is too weak or
discharged.
XJump-start the vehicle (Ypage 308).
If the engine does not start despite attempt stojump-start it:
XConsult aqualified specialist workshop.
The starter motor was exposed to athermal load that was too high.
XTry to start the engine again (Ypage 133).
If the engine still does not start:
XConsult aqualified specialist workshop.
The engine is not running
smoothly and is misfir-
ing.There is amalfunction in the engine electronics or in amechanical
componentoft he engine management system.
XOnly depress the accelerator pedal slightly.
Otherwise, non-combusted fuel may get into the catalytic converter
and damage it.
XHave the cause rectified immediately at aqualified specialist work-
shop.
The coolant temperature
gauge shows avalue
above 248 ‡(120 †).The coolant level is too low. The coolant is too hot and the engine is no
longer being cooled sufficiently.
XStop as soon as possible and allow the engine and the coolant to
cool down.
XCheck the coolant level (Ypage 290). Observe the warning notes
as you do so and add coolant if necessary.
138Driving
Driving and parking

Rthe availability of the ECO start/stopfun ction
Rthe driver assistance systems
Rthe availability of gliding mode
Furtheri nformation for automatic drive program
characteristics (
Ypage 144).
Additionally, in drive program Iyo uc an config-
ur et he respectiv evehicl echaracteristics using
the multimedia system. Yo ucan fin dinforma-
tio na bout thisint he Digita lOperator' sManual.
Each tim eyou start the engine with the Smart-
Key or the Start/Stop button, drive program Cis
activated .For furthe rinformation abou tstarting
the engine ,see (
Ypage 133).
Selecting the driv eprogram
XPress DYNAMIC SELECTs witch :forwards
or backwards unti lthe desired drive program
is selected.
The status ico nofthe selected drive program
is shown in the multifunctio ndisplay .
In addition, the current drive progra msettings
ar ed isplayed brieflyinthe multimedia system
display.
Yo uc an also change gear yourself using the
steering whee lpaddl eshifters. For furthe rinfor-
matio nont he manua ldrive program
(
Ypage 146).
Additional settings
:Positio nofthe exhaust fla p(Ypage 137)
;ECO start/sto pfunctio n(Ypage 135)
=ESP®(Ypage 67)
?Suspension (Ypage 172)
APermanent activatio nofmanualgears hifting
(Ypage 146)
When yo upress buttons :-A the corre-
sponding setting is selected .The DYNAMIC
SELECT switc hsetting is overwritten.
These setting swilla lsobem aintaine difyou
change with the DYNAMIC SELECTs witch in
drive program RACE(S-MODEL), S+,Sor C.
If yo uswitch to drive program I,a llstored char-
acteristics will be accepted .This is als othe case
if yo uhavep reviously presse dbuttons :-A.
Automati ctransmission
Important safety notes
GWARNING
If the engine spee disabove the idling speed
and yo uengag etransmission position Dor R,
the vehicl ecould pull away suddenly. There is
ar iskofana ccident.
When engaging transmission position Dor R,
always firmlyd epress the brake peda land do
not simultaneously accelerate.
GWARNING
The automatic transmission switches to neu-
tralp ositionNwhen yo uswitch off the engine.
The vehicl emayrollaway. There is ariskofa n
accident.
140Automati ctransmission
Driving an dparking

After switching off the engine,alway sswitch
to parking position P.Prevent the parked vehi-
cle from rolling away by applying the parking
brake.
DIREC TSELECT lever
Overvie woftransmission positions
jPark positio nwithp arking lock
kReverse gear
iNeutral
hDrive
The DIRECT SELECTl ever is on the right of the
steering column.
The DIRECT SELECTl ever always returns to its
original position. The current transmission posi-
tion P,R, Nor Dappear sinthe transmission
positio ndisplay in the multifunctio ndisplay
(
Ypage 142).
Engagin gpark position P
!If the engine speed is too high or the vehicle
is moving, do not shift the automatic trans-
mission directl yfrom Dto R,f rom Rto Dor
directl ytoP.T he automatic transmission
could otherwise be damaged.
XPush the DIRECT SELECTl ever in the direction
of arrow P.
Engagingpark position Pautomatically
Park position Pis automaticall yengaged if:
Ryous witch off the engine using the SmartKey
and remove the SmartKey
Ryo us witch off the engine using the SmartKey
or using the Start/Stop button and open the
driver's door or front-passenger door
Rthe driver's door is opene dwhenthe vehicl eis
stationar yordriving at ver ylow speed and the
transmission is in position Dor R
Unde rcertain conditions, the automatic trans-
mission shifts automaticall ytotransmission
position Pif the HOLD functio norDISTRONIC
PLU Sisa ctivated.O bservethe informatio non
the HOLD functio n(
Ypage 170)and on
DISTRONICP LUS(Ypage 165).
Engagin grevers egearR
!Onlys hift the automatic transmission to R
when the vehicl eisstationary.
XIf the transmission is in position Dor N:p ush
the DIRECT SELECTl ever up past the first
point of resistance.
XIf the transmission is in position P:depress
the brake peda land push the DIRECT SELECT
lever up past the first point of resistance.
The ECO start/sto pfunctio nisn ot available
when revers egearise ngaged .Further informa-
tio nont he ECO start/sto pfunction
(
Ypage 135).
Shiftin gtoneutral N
GWARNING
If children ar eleftu nsupervised in the vehicle,
they could:
Ropen the doors ,thuse ndangering other
people or roa dusers.
Rget outa nd disrupt traffic.
Roperate the vehicle's equipment.
Additionally, children could set the vehicl ein
motion if, for example, they:
Rrelease the parking brake.
Rshifting the automatic transmission outo f
park position P
RStartthe engine.
Automatict ransmission141
Driving andparking
Z

There isarisk of an accident and injury.
When leaving the vehicle, alwayst ake the
SmartKey with you and lock the vehicle. Never
leave children or animals unattended in the
vehicle. Always keep the SmartKey out of
reach of children.
XIf the transmission is in position Dor R:p ush
the DIRECT SELECT lever up or down to the
first point of resistance.
XIf the transmission is in position P:depress
the brake pedal and push the DIRECT SELECT
lever up or down to the first point of resist-
ance.
If you switch the engine off with the transmis-
sion in position Ror D,t he automatic transmis-
sion shifts to Nautomatically.
With the SmartKey: if you then open the driv-
er's door or the front-passenger door or remove
the SmartKey from the ignition, the automatic
transmission shifts to Pautomatically.
With the Start/Stop button: if you then open
the driver's door or the front-passenger door,
the automatic transmission shifts to Pautomat-
ically.
If you want the automatic transmission to
remain in neutral N,e .g. when having the vehicle
cleaned in an automatic car wash with atowing
system:
XVehicles with the Start-Stop button:
remove the Start-Stop button from the igni-
tion lock.
XInsert the SmartKey into the ignition lock.
XAll vehicles: switch the ignition on.
XDepress the brake pedal and keep it
depressed.
XShift to neutral N.
XRelease the brake pedal.
XRelease the electric parking brake.
XSwitch off the ignition and leave the SmartKey
in the ignition lock.
Engaging drive position D
XIf the transmission is in position Ror N:p ush
the DIRECT SELECT lever down past the first
point of resistance.
XIf the transmission is in position P:depress
the brake pedal and push the DIRECT SELECT lever down past the first point of resistance.
Transmission position and drive pro-
gram display
The current transmission position and drive pro-
gram appear in the multifunction display.
:Status symbol drive program
;Transmission position
=Gear
The arrows in the transmission position display
show how and into which transmission positions
you can shift using the DIRECT SELECT lever.
If the transmission position display in the mul-
tifunction display is not working, you should pull
away carefully to check whether the desired
transmission position is engaged. For this pur-
pose, we recommend selectin gtransmission
position Dand drive program E(drive program C
in Mercedes-AMG vehicles) or S.
142Automatic transmission
Driving and parking

Transmission positions
BPark position
Thisprevents the vehicl efromr olling
away when stopped.
Onlys hift the transmission into posi-
tion Pwhen the vehicl eisstationary
(
Ypage 141). The parkin gloc k
shoul dnot be used as abrake when
parking. Alway sapply the electronic
parkin gbrake in additio ntothe park-
ing lock in order to secur ethe vehi-
cle.
Park position Pis automatically
engaged if:
Ryo us witch off the engine using the
SmartKeya nd remove the Smart-
Key
Ryo us witch off the engine using the
key or using the Start/Stop button
and open the driver's door or front-
passenge rdoor
Rthe driver's door is opene dwhen
the vehicl eisstationar yordriving
at ver ylow spee dand the trans-
mission is in position Dor R
If the vehicl eelectronics ar emalfunc-
tioning ,the transmission mayb e
locked in position P.H avet he vehicle
electronics checked immediatel yata
qualified specialis tworkshop.
CRevers egear
Onlys hift the transmission into posi-
tion Rwhen the vehicl eisstationary.
ANeutral
Do not shift the transmission to N
whil edriving. Otherwise, the auto-
matic transmission could be dam-
aged.
No powe ristransmitted fromt he
engine to the drive wheels.
Releasing the brake peda lwilla llow
yo utom ovet he vehicl efreely, e.g .to
push it or tow it.
If ESP
®is deactivated or faulty: shift
the transmission to position Nif the
vehicl eisind angerofs kidding,e.g.
on icy roads.
If yo uswitch the engine off with the
transmission in position Ror D,t he
automatic transmission shifts to N
automatically.
!Rolling in neutral Ncan damage
the drive train.
7Drive
The automatic transmission changes
gear automatically. All forward gears
ar ea vailable.
Driving tips
Changin ggear
The automatic transmission shifts to the indi-
vidua lgears automaticall ywhenitisint rans-
mission position D.T hisa utomatic gear shifting
behavio risdetermine dby:
Rthe selecte ddrive program
Rthe positio nofthe accelerator pedal
Rthe roa dspeed
Accelerator peda lposition
Your style of drivin ginfluences how the auto-
matic transmission shifts gear:
Rlittle throttle :early upshifts
Rmor ethrottle :lat eu pshifts
Double-clutc hfunction
When shifting down, the double-clutch function
is active regardless of the currentl yselected
drive program. The double-clutch function
Automati ctransmission143
Driving an dparking
Z

reduces loadchange reactions and is conducive
to as porty driving style .The sound generated by
the double-clutch function depends on the drive
programs elected.
Kickdown
Use kickdown for maximu macceleration.
XDepress the accelerator pedalb eyond the
pressure point.
The automatic transmission shifts to alower
gear depending on the engine speed.
XEase off the accelerator pedalo nce the
desired speedisr eached.
The automatic transmission shifts back up.
Rocking the vehicle free
Rocking the vehicl efree by shifting back and
forth between transmission positions Dand R
can help to free avehicl ethat has become stuck
in mud or snow.
The vehicle's engine management restricts
switching between transmission positions D
and Rto speeds up to amaximu mof5m ph
(9 km/h).
To shift back and forth between transmission
positions Dand R,m ove the DIRECT SELECT
lever up and down past the point of resistance.
Glidingm ode (Mercedes-AMG vehicles)
Gliding mode is characterized by the following:
Rthe combustion engine is disconnected from
the drive train.
Rthe engine speed corresponds to the idling
speed.
Rstatus icon Cgoes out and status icon :is
displayed in the multifunction display
(
Ypag e142).
In drive program C,y ou can deactivate and acti-
vate gliding mode using the ECO button
(
Ypag e136). Gliding mode can be activated under the follow-
ing conditions:
Rthe speedisw
ithinas uitable range.
Rthe course of the road is suitable ,e.g. there
are no steep up or downhill gradients.
Ryou are no longer depressing the accelerator
pedal.
Gliding mode is deactivated under the following conditions:
Ryou depress the accelerator pedal.
Ryou depress the brake pedal.
Ryou use the DIRECT SELECT lever to switch
the transmission position (Ypag e141).
Ryou switch to drive program RACE
(S‑MODEL), S+orS(Ypag e139).
Ryou activate manua lgearshifting
(Ypag e146).
Ryou leave the suitable speedr ange.
iIf you have selected the "Comfort" setting
for the drive (engine management) in drive
program I,y ou can als oactivate gliding mode.
You can find informatio nabout this in the Dig-
ital Operator's Manual.
Drive programs
All vehicles (except Mercedes-AMG
vehicles)
Drive program I(Individual)
In drive program Ithe following properties of the
drive programc an be selected:
Rthe drive (engine and transmission manage-
ment)
Rthe suspension
Rthe steering
Rthe availability of the ECO start/stop function
Rthe climate control
Information about configuring drive program I
with the multimedia system can be found in the
Digital Operator's Manual.
iTo permanently select the gears in drive
program Iusing the steering whee lpaddle
shifters, select the M(manual) setting for the
drive.
144Automatic transmission
Driving and parking

Problems with the transmission
ProblemPossible causes/consequences andMSolutions
The transmission has
problems shifting gear.The transmission is losing oil.
XHave the transmission checked ataqualified specialist workshop
immediately.
The acceleration ability
is deteriorating.
The transmission no lon-
ger changes gear.The transmission is in emergency mode.
It is only possible to shift into secondgear and reverse gear.
XStop the vehicle.
XShift the transmission to position P.
XSwitch off the engine.
XWait at least ten seconds before restarting the engine.
XShift the transmission to positionDor R.
If D is selected, the transmission shifts into secondgear; ifRis
selected, the transmission shifts into reverse gear.
XHave the transmission checked at aqualified specialist workshop
immediately.
Transfer case
This section is only valid for vehicles with 4-
wheel drive (4MATIC). Power is always trans-
mitted to both axles.
!Performancet ests may only be carried out
on a2 -axle dynamometer. The brake system
or transfer case could otherwise be damaged. Contact aqualified specialist workshop for a
performancet est.
!Since ESP®engages automatically, the igni-
tion must be switched off (the SmartKey or
Start/Stop button must be in position 0or 1)
if:
Rthe electric parking brake is being tested
on abrake dynamometer
Rthe vehicle is being towed with only one
axle raised (not permitted for vehicles with
4MATIC).
The brake system could otherwise be dam-
aged.
!Vehicles with 4MATIC must not be towed
with either the front or the rear axle raised, as doing so will damage the transmission.
Refueling
Important safety notes
GWARNING
Fuel is highly flammable. If you handle fuel
incorrectly, there is arisk of fire and explo-
sion.
You must avoid fire, open flames, creating
sparks and smoking. Switch off the engine
and, if applicable, the auxiliary heating before refueling.
GWARNING
Fuel is poisonous and hazardous to health.
There is arisk of injury.
You must make sure that fuel does not come into contact with your skin, eyes or clothing
and that it is not swallowed. Do not inhale fuel
vapors. Keep fuel away from children.
If you or others come into contact with fuel,
observe the following:
RWash away fuel from skin immediately
using soap and water.
RIf fuel comes into contact with your eyes,
immediately rinse them thoroughly with
Refueling149
Driving and parking
Z

To ensure that the vehicle is secured against
rolling away unintentionally:
Rthe electric parking brake must be applied.
Rthe transmission must be in positionPand the
SmartKey must be removed from the ignition
lock.
Rthe front wheels must be turned towards the
curb on steep uphill or downhill gradients.
Rthe empty vehicle must be secured at the
front axle with awheel chock or similar, for
example, on uphill or downhill gradients.
Ral aden vehicle must also be secured at the
rear axle with awheel chock or similar, for
example, on uphill or downhill gradients.
Switching off the engine
Important safety notes
GWARNING
The automatic transmission switches to neu-
tral position Nwhen you switch off the engine.
The vehicle may roll away.T here isarisk of an
accident.
After switching off the engine, alwayss witch
to parking position P.Prevent the parked vehi-
cle from rolling away by applying the parking
brake.
Vehicles with automatic transmission
XApply the electric parking brake.
XShift the transmission to position P.
XWith the SmartKey:turn the SmartKey to
position 0in the ignition lock and remove it.
The immobilizer is activated.
XWith the Start/Stop button: press the
Start/Stop button (Ypage 131).
The engine stops and all the indicator lamps in
the instrument cluster go out.
When the driver's door is closed, this corre-
sponds to SmartKey position 1.When the
driver's door is open, this corresponds to
SmartKey position 0:"SmartKey removed".
If you switch the engine off with the transmis-
sion in position Ror D,t he automatic transmis-
sion shifts to Nautomatically.
With the SmartKey: if you then open the driv-
er's door or the front-passenger door or remove the SmartKey from the ignition, the automatic
transmission shifts to
Pautomatically.
With the Start/Stop button: if you then open
the driver's door or the front-passenger door,
the automatic transmission shifts to Pautomat-
ically.
If you want the automatic transmission to
remain in neutral N,e .g. when having the vehicle
cleaned in an automatic car wash with atowing
system:
XVehicles with the Start-Stop button:
remove the Start-Stop button from the igni-
tion lock.
XInsert the SmartKey into the ignition lock.
XAll vehicles: switch the ignition on.
XDepress the brake pedal and keep it
depressed.
XShift to neutral N.
XRelease the brake pedal.
XRelease the electric parking brake.
XSwitch off the ignition and leave the SmartKey
in the ignition lock.
The engine can be switched off in an emergency
while the vehicle is in motion by pressing and
holding the Start/Stop button for three sec-
onds. This function operates independently of
the ECO start/sto pautomatic engine switch-off
function.
Electric parking brake
General notes
GWARNING
If you leave children unsupervised in the vehi-
cle, they could set it in motion by, for example:
Rrelease the parking brake.
Rshift the automatic transmission out of the
parking position P.
Rstart the engine.
In addition, they may operate vehicle equip-
ment and become trapped. There is arisk of
an accident and injury.
When leaving the vehicle, alwayst ake the
SmartKey with you and lock the vehicle. Never
leave children unsupervised in the vehicle.
Parking153
Driving and parking
Z

The function of the electric parking brake is
dependent on the on-board voltage. If the on-
board voltage is low or there isamalfunction in
the system, it may not be possible to apply the
released parking brake.
XIf this is the case, only park the vehicle on
level ground and secure it to prevent it rolling
away.
XShift the automatic transmission to position
P.
It may not be possible to release an applied
parking brake if the on-board voltage is low or
there is amalfunction in the system. Contact a
qualified specialist workshop.
The electric parking brake performs afunction
test at regular intervals while the engine is
switched off. The sounds that can be heard while
this is occurringa re normal.
Applying or releasing manually
XTo apply:push handle :.
When the electric parking brake is applied,
the red F(USA only) or !(Canada
only) indicator lamp lights up in the instru-
ment cluster.
The electric parking brake can also be applied
when the SmartKey is removed.
XTo release: pull handle:.
The red F(USA only) or !(Canada
only) indicator lamp in the instrument cluster
goes out.
The electric parking brake can only be released:
Rwhen the SmartKey is in position 1or 2in the
ignition lock (Ypage 131) or
Rif the ignition was switched on using the
Start/Stop button
Applying automatically
The electric parking brake is automatically
applied when the transmission is in position P
and:
Rthe engine is switched off or
Rthe driver is not wearing aseat belt and the
driver's door is opened
To prevent the electric parking brake from being automatically applied, pull handle :.
The electric parking brake is also engaged auto-
matically if:
RDISTRONIC PLUS brings the vehicle to a
standstill or
Rthe HOLD function is keeping the vehicle sta- tionary
RActive Parking Assist is keeping the vehicle
stationary
In addition, at least one of the following condi-
tions must be fulfilled:
Rthe engine is switched off
Rthe driver is not wearing aseat belt and the
driver's door is opened
Rthere is asystem malfunction
Rthe power supply is insufficient
Rthe vehicle is stationary for alengthy period
The red F(USA only) or !(Canada only)
indicator lamp in the instrument cluster goes
out.
The electric parking brake is not automatically
engaged if the engine is switched off by the ECO
start/sto pfunction.
Releasing automatically
Your vehicle's electric parking brake is auto-
matically released if all of the following condi-
tions are met:
Rthe seat belt has been fastened.
Rthe engine is running.
Ryou accelerate and the transmission is in
position Dor R.
or
you shift the transmission position from Pto
position Dor R.Y ou will need to accelerate
more on steeper gradients.
If the transmission is in position R,the trunk lid
must be closed.
154Parking
Driving and parking