Battery MERCEDES-BENZ C300 SPORT 2008 W204 User Guide

108 Controls in detail
Lighting
Exterior lamp switch
Low beam headlamps
The low beam headlamps can be switched
on and off with the exterior lamp switch us-
ing the manual headlamp mode.
Switching on: Turn the exterior lamp
switch to positionB.
The green indicator lampC in the
exterior lamp switch comes on.
iIf you drive in countries where vehicles drive
on the other side of the road than the country in
which the vehicle is registered, you must have
the headlamps modified for symmetrical low
beams. Relevant information can be obtained at
your authorized Mercedes-Benz Center.1‚Standing lamps, left (turn left two
stops)
2ˆStanding lamps, right (turn left
one stop)
3MOff
Daytime running lamp mode
(
page 110)
4*Automatic headlamp mode
Daytime running lamp mode
(
page 110)
5CParking lamps (also side marker
lamps, tail lamps, license plate
lamps, instrument panel lamps)
6BLow beam headlamps or high
beam headlamps
7‡Front fog lamps
8†Rear fog lamp
iIf you hear a warning signal you have
forgotten to switch off the low beam headlamps
or the parking lamps before opening the driver’s
door.
In addition the message
Switch Off Lights
appears in the multifunction display.
Switch off the low beam headlamps or the park-
ing lamps.
If the message
Switch Off Lights or Re-
move Key
appears in the multifunction display
remove the SmartKey from the starter switch or
switch off the automatic headlamp mode.
!Failure to switch off the exterior lamps when
leaving the vehicle may result in a discharged
battery.

115 Controls in detail
Lighting
Automatic control
Deactivating: Press button2.
The button engages when pressed in.
Automatic control of the interior light-
ing is deactivated.
The interior lighting remains switched
off in darkness, even when you:

unlock the vehicle

open a door

remove the SmartKey from the
starter switch
Activating: Press button2 again.
The button returns to its original posi-
tion and sits flush with the other but-
tons. Automatic control of the interior
lighting is activated.
The interior lighting switches on in
darkness, when you:

unlock the vehicle

open a door

remove the SmartKey from the
starter switch
The interior lighting switches off
automatically.
You can set whether the interior light-
ing should come on when you remove
the key from the starter switch via the
control system, see “Setting interior
lighting delayed shut-off”
(
page 173).Manual control
Switching on/off front interior light-
ing: Press button4.
Switching on/off rear interior light-
ing: Press button 1.
Switching on/off front reading
lamps: Press button 3 or 5.
The left and right front reading lamps
are located in the lower edge of the in-
terior rear view mirror.
!An interior lamp switched on manually does
not go out automatically.
Leaving an interior light switch in the ON position
for extended periods of time with the engine
turned off could result in a discharged battery.
iThe interior lighting is factory-set to auto-
matic mode.
iIf the door remains open, the interior lighting
switches off automatically after approximately
5minutes.

129 Controls in detail
Driving and parking
Starting difficulties
The engine does not start. You can hear
the starter.
There could be a malfunction

in the engine electronics, or

in the fuel supply system
Carry out the following steps:
If you are starting the engine with the
SmartKey: Turn SmartKey in starter
switch to position0 and repeat starting
procedure (
page 126).
If you are starting the engine with
KEYLESS-GO*: Close any doors that
may be open to allow for better detec-
tion of the SmartKey with
KEYLESS-GO*.
or
Remove the KEYLESS-GO* start/stop
button from starter switch.
Start the engine with the SmartKey as
radio signals from another source may
be interfering with the SmartKey with
KEYLESS-GO*.
Repeat the starting procedure
(
page 126).
If the engine does not start after several
starting attempts:
Call Roadside Assistance.
Notify an authorized Mercedes-Benz
Center.
The engine does not start. You cannot
hear the starter.
The battery may not be sufficiently
charged.
Get a jump start (page 451).
If the engine will not start despite a jump
start:
Call Roadside Assistance.
Notify an authorized Mercedes-Benz
Center.
Driving off
!Remember that extended starting attempts
can drain the battery.
Warning!G
When leaving the vehicle, always remove the
SmartKey or SmartKey with KEYLESS-GO*
(Canada only) from the starter switch, take
it with you, and lock the vehicle. Do not
leave children unattended in the vehicle, or
with access to an unlocked vehicle. Children
could release the parking brake, which
could result in an accident and/or serious
personal injury.
Warning!G
On slippery road surfaces, never downshift
in order to obtain braking action. This could
result in drive wheel slip and reduced vehi-
cle control. Your vehicle’s ABS will not pre-
vent this type of loss of control.

256 Controls in detail
Dual-zone automatic climate control
Maximum cooling MAX COOL
(USA only)
You can use this setting to provide the fast-
est possible cooling of the vehicle interior
(when windows and tilt/sliding sunroof or
tilt/sliding panel* are closed).
Activating: Press button3
(
page 250).
The indicator lamp in the button comes
on.
The air conditioning switches
automatically to the following functions:

maximum cooling

maximum blowing power

the air recirculation mode is switched
on
Deactivating: Press button3
(
page 250) again.
The indicator lamp in the button goes
out. The previous settings are once
again in effect.
Rear window defroster
Activating: Switch on the ignition.
Press button¯ (page 250).
The indicator lamp in the button comes
on.
iTo switch the maximum cooling function off,
you can also press button ´, U ory
(
page 250).
Warning!G
Any accumulation of snow and ice should be
removed from the rear window before driv-
ing. Visibility could otherwise be impaired,
endangering you and others.
!The rear window defroster uses a large
amount of power. To keep battery drain to a min-
imum, switch off the defroster as soon as the
rear window is clear.

257 Controls in detail
Dual-zone automatic climate control
Deactivating: Press button¯
(
page 250).
The indicator lamp in the button goes
out.
Air recirculation mode
Switch to air recirculation mode to prevent
unpleasant odors from entering the vehicle
from the outside (e.g. before driving
through a tunnel). This setting cuts off the
intake of outside air and recirculates the
air in the passenger compartment.Activating: Press button,
(
page 250).
The indicator lamp in the button comes
on.
Deactivating: Press button,
(
page 250) again.
The indicator lamp in the button goes
out.
iThe rear window defroster is automatically
deactivated after some time of operation de-
pending on the outside temperature.
iIf the rear window defroster switches off too
soon and the indicator lamp goes out, this indi-
cates that too many electrical consumers are op-
erating simultaneously and the load on the
battery is reducing available voltage. The system
responds automatically by deactivating the rear
window defroster.
Warning!G
Fogged windows impair visibility, endanger-
ing you and others. If the windows begin to
fog on the inside, switching off the air
recirculation mode immediately should clear
interior window fogging. If interior window
fogging persists, make sure the air
conditioning (
page 258) is activated, or
press buttony.
iThe air recirculation mode is activated auto-
matically at high outside temperatures.
The indicator lamp in button, is not lit when
the air recirculation mode is automatically
switched on.
A quantity of outside air is added after approxi-
mately 30 minutes.
iThe air recirculation mode is deactivated au-
tomatically:

after 5 minutes if the outside temperature is
below approximately 41°F (5°C)

after 5 minutes if the air conditioning is
turned off

after 30 minutes if the outside temperature
is above approximately 41°F (5°C)

265 Controls in detail
3-zone automatic climate control* (Canada only)
Rear window defroster
Activating: Switch on the ignition.
Press button¯ (page 259).
The indicator lamp in the button comes
on.
Deactivating: Press button¯
(
page 259).
The indicator lamp in the button goes
out.
Air recirculation mode
Switch to air recirculation mode to prevent
unpleasant odors from entering the vehicle
from the outside (e.g. before driving
through a tunnel). This setting cuts off the
intake of outside air and recirculates the
air in the passenger compartment.
!The rear window defroster uses a large
amount of power. To keep battery drain to a min-
imum, switch off the defroster as soon as the
rear window is clear.
iThe rear window defroster is automatically
deactivated after some time of operation de-
pending on the outside temperature.
Warning!G
Any accumulation of snow and ice should be
removed from the rear window before driv-
ing. Visibility could otherwise be impaired,
endangering you and others.
iIf the rear window defroster switches off too
soon and the indicator lamp goes out, this indi-
cates that too many electrical consumers are op-
erating simultaneously and the load on the
battery is reducing available voltage. The system
responds automatically by deactivating the rear
window defroster.
Warning!G
Fogged windows impair visibility, endanger-
ing you and others. If the windows begin to
fog on the inside, switching off the air
recirculation mode immediately should clear
interior window fogging. If interior window
fogging persists, make sure the air
conditioning (
page 267) is activated, or
press buttony.

266 Controls in detail
3-zone automatic climate control* (Canada only)
Activating: Press button,
(
page 259).
The indicator lamp in the button comes
on.
Deactivating: Press button,
(
page 259) again.
The indicator lamp in the button goes
out.
Residual engine heat and ventilation
With the engine switched off, it is possible
to continue to heat or ventilate the interior
for approximately 30 minutes. This feature
makes use of the residual heat produced
by the engine.
Activating: Switch off the ignition.
Press buttonT (page 259).
The indicator lamp in the button comes
on.
Deactivating: Press buttonT
(
page 259) again.
The indicator lamp in the button goes
out.
iThe air recirculation mode is activated auto-
matically at high outside temperatures.
The indicator lamp on button, is not lit when
the air recirculation mode is automatically
switched on.
A quantity of outside air is added after approxi-
mately 30 minutes.
iThe air recirculation mode is deactivated au-
tomatically:

after 5 minutes if the outside temperature is
below approximately 7°C (45°F)

after 5 minutes if the air conditioning is
turned off

after 30 minutes if the outside temperature
is above approximately 5°C (41°F)
iIf you switch on the residual heat function
when outside temperatures are high, only the
ventilation will be switched on.
iRegardless of the selected air volume, the
blower operates at low speed when heating. In
case of ventilation the blower operates at higher
speed.
iHow long the system will provide heating de-
pends on

the coolant temperature

the temperature set by the operator
iThe residual heat is automatically turned off:

when the ignition is switched on

after approximately 30 minutes

if the battery voltage drops

if the coolant temperature is too low

271 Controls in detail
Trunk
Trunk emergency release
With the emergency release button, the
trunk can be opened from inside the trunk.
1Emergency release buttonBriefly press emergency release
button1.
The trunk opens.Illumination of the emergency release but-
ton:

The button will flash for 30 minutes af-
ter opening the trunk.

The button will flash for 60 minutes af-
ter closing the trunk.iThe emergency release button unlocks and
opens the trunk while the vehicle is standing still
or in motion.
iThe emergency release button does not
open the trunk if the vehicle battery is dis-
charged or disconnected.

295 Controls in detail
Useful features
lTele Aid*
The Tele Aid system
(Tele
matic Alarm Identification on De-
mand)
The Tele Aid system consists of three
types of response:

automatic and manual emergency

Roadside Assistance, and

informationThe Tele Aid system is operational provid-
ing that the vehicle’s battery is charged,
properly connected, not damaged and
telephone phone and GPS coverage are
available.
The speaker volume of a Tele Aid call can
be adjusted when using the volume control
on the multifunction steering wheel. To
raise, press buttonæ and to lower,
press buttonç or use the audio system
rotary control button (
page 189).
To activate, press the SOS button, the
Roadside Assistance button*b or
the Information button*}, depend-
ing on the type of response required.
Shortly after the completion of your
Tele Aid acquaintance call, you will receive
a user ID and password. By visiting
www.mbusa.com and selecting “Tele Aid”
(USA only), you will have access to account
information, remote door unlock and
more.
!The initial activation of the Tele Aid system
may only be performed by completing the sub-
scriber agreement and placing an acquaintance
call using the Information button*}. Failure
to complete either of these steps will result in a
system that is not activated.
If you have any questions regarding activation,
please call the Response Center at
1-800-756-9018 (in the USA) or
1-888-923-8367 (in Canada).
iThe Tele Aid system utilizes the telephone
network for communication and the GPS (Global
Positioning System) satellites for vehicle loca-
tion. If either of these signals are unavailable, the
Tele Aid system may not function and if this oc-
curs, assistance must be summoned by other
means.
iThe SOS button, the Roadside Assistance
button*b, and the Information
button*} are located in the overhead con-
trol panel (
page 31).

307 Controls in detail
Useful features
Programming tips
If you are having difficulty programming
the integrated remote control, here are
some helpful tips:

Check the frequency of hand-held re-
mote control5 (typically located on
the reverse side of the remote). The in-
tegrated remote control is compatible
with radio-frequency devices operating
between 280-390 MHz.

Put a new battery in hand-held remote
control5. This will increase the likeli-
hood of the hand-held remote control
sending a faster and more accurate sig-
nal to the integrated remote control.

While performing step 3, hold
hand-held remote control5 at differ-
ent lengths and angles from the signal
transmitter button (2, 3 or4) you
are programming. Attempt varying an-
gles at the distance of 2 to 5 in
(5 to 12 cm) away or the same angle at
varying distances.

If another hand-held remote control is
available for the same device, try the
programming steps again using that
other hand-held remote control. Make
sure new batteries are in the hand-held
remote control before beginning the
procedure.

Straighten the antenna wire from the
garage door opener assembly. This
may help improve transmitting and/or
receiving signals.
iCertain types of garage door openers are in-
compatible with the integrated remote control. If
you should experience further difficulties with
programming the integrated remote control,
contact an authorized Mercedes-Benz Center, or
call Mercedes-Benz Customer Assistance Cen-
ter (in the USA only) at 1-800-FOR-MERCedes, or
Customer Service (in Canada) at
1-800-387-0100.
iUSA only:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interfer-
ence, and
(2) this device must accept any interference re-
ceived, including interference that may
cause undesired operation.
Any unauthorized modification to this device
could void the user’s authority to operate the
equipment.
iCanada only:
This device complies with RSS-210 of Industry
Canada. Operation is subject to the following
two conditions:
(1) This device may not cause interference, and
(2) this device must accept any interference re-
ceived, including interference that may
cause undesired operation of the device.
Any unauthorized modification to this device
could void the user’s authority to operate the
equipment.