garage door opener MERCEDES-BENZ C350 4MATIC 2007 W203 Owner's Manual

Contents
Power tilt/sliding sunroof* ................ 224
Opening and closing
the power tilt/sliding sunroof ...... 224
Synchronizing
the power tilt/sliding sunroof ...... 226
Driving systems ................................. 227
Cruise control............................... 227
Loading .............................................. 230
Roof rack* .................................... 230
Ski sack* (Canada only) ............... 230
Split rear bench seat* .................. 233
Loading instructions ..................... 235
Cargo tie-down rings* .................. 236
Useful features .................................. 237
Storage compartments................. 237
Cup holders .................................. 239
Ashtrays ....................................... 241
Cigarette lighter ........................... 242
Power outlet ................................. 243
Telephone*................................... 244
Tele Aid* ...................................... 247
Garage door opener* ................... 253
Operation......................................... 259
The first 1 000 miles (1 500 km)......... 260
Driving instructions............................ 261
Drive sensibly – save fuel ............. 261
Drinking and driving ..................... 261
Pedals .......................................... 261
Power assistance ......................... 262
Brakes .......................................... 262
Driving off .................................... 263
Parking ......................................... 264
Tires ............................................. 264
Hydroplaning ................................ 265
Tire traction.................................. 265
Tire speed rating .......................... 266
Winter driving instructions ........... 267
Standing water ............................. 268
Passenger compartment .............. 268
Driving abroad.............................. 268
Control and operation
of radio transmitters .................... 268
Catalytic converter ....................... 269
Emission control .......................... 270
Coolant temperature .................... 270At the gas station .............................. 271
Refueling ...................................... 271
Check regularly
and before a long trip................... 273
Engine compartment ......................... 274
Hood ............................................ 274
Engine oil ..................................... 276
Transmission fluid level................ 277
Coolant level ................................ 278
Battery ......................................... 279
Windshield washer system
and headlamp cleaning system* .. 280
Tires and wheels................................ 281
Important guidelines .................... 281
Tire care and maintenance........... 282
Direction of rotation..................... 284
Loading the vehicle ...................... 284
Recommended
tire inflation pressure ................... 289
Checking tire inflation pressure ... 290
MOExtended system* .................. 294
Tire labeling ................................. 295
Load identification ....................... 299
DOT, Tire Identification Number
(TIN) ............................................. 299
Maximum tire load ....................... 301

29 At a glance
Overhead control panel
Overhead control panel
ItemPage
1Rear interior lighting on/off 117
2Power tilt/sliding sunroof*224
3Right reading lamp on/off117
4Interior lighting control116
5Interior rear view mirror42,
160
6Garage door opener*253
7Hands-free microphone for
Tele Aid* (emergency call
system) and telephone*146,
208,
247
8Left reading lamp on/off117
9Tele Aid* (emergency call
system) button247

253 Controls in detail
Useful features
Stolen Vehicle Recovery services
In the event your vehicle was stolen:
Report the incident to the police.
The police will issue a numbered
incident report.
Pass this number on to the
Mercedes-Benz Response Center along
with your password issued to you when
you subscribed to the service.
The Response Center will then attempt
to covertly contact the vehicle’s
Tele Aid system. Once the vehicle is
located, the Response Center will
contact the local law enforcement and
you. The vehicle’s location will only be
provided to law enforcement.
Garage door opener*
The integrated remote control is capable of
operating up to three separately controlled
devices. It provides a convenient way to re-
place up to three hand-held remote con-
trols used to operate devices such as
garage door openers, gate openers, or oth-
er devices compatible with HomeLink
® or
some other systems.
Before the integrated remote control can
be used, it must be programmed to the ga-
rage door opener, gate operator or other
device you wish to operate. See the follow-
ing instructions for programming informa-
tion.
iThe remote door unlock feature is available
if the relevant cellular phone network is avail-
able.
The SOS button will flash and the message
Connecting call will appear in the multifunc-
tion display to indicate receipt of the door unlock
command.
Once the vehicle is unlocked, a Response Center
specialist may attempt to establish voice contact
with the vehicle occupants.
If the tailgate recessed handle was pulled for
more than 20 seconds before door unlock autho-
rization was received by the Response Center,
you must wait 15 minutes before pulling the tail-
gate recessed handle again.
iWhen the anti-theft alarm* stays on for
more than 30 seconds, a call is initiated auto-
matically to the Response Center. See
“Anti-theft alarm system*” (
page 89).

254 Controls in detail
Useful features
Interior rear view mirror with integrated re-
mote control
1Indicator lamp
2 3 4Signal transmitter button
Needed for programming (not part of vehi-
cle equipment):
5Hand-held remote control of ga-
rage door opener, gate operator
or other device
6Hand-held remote control but-
tonProgramming the integrated remote
control
Step 1:
Switch on the ignition (page 32).
Step 2:
If you have previously programmed a
signal transmitter button and wish to
retain its programming, proceed to
step 3.
If you are programming the integrated
remote control for the first time, press
and hold the two outer signal transmit-
ter buttons2 and4 and release
them only when indicator lamp1 be-
Warning!G
Before programming the integrated remote
control to a garage door opener or gate
operator, make sure people and objects are
out of the way of the device to prevent po-
tential harm or damage. When programming
a garage door opener, the door moves up or
down. When programming a gate operator,
the gate opens or closes.
Do not use the integrated remote control
with any garage door opener that lacks
safety stop and reverse features as required
by U.S. federal safety standards (this
includes any garage door opener model
manufactured before April 1, 1982).
A garage door that cannot detect an object
- signaling the door to stop and reverse -
does not meet current U.S. federal safety
standards.
When programming a garage door opener,
park outside the garage.
Do not run the engine while programming
the integrated remote control. Inhalation of
exhaust gas is hazardous to your health. All
exhaust gas contains carbon monoxide
(CO), and inhaling it can cause unconscious-
ness and possible death.

255 Controls in detail
Useful features
gins to flash after approximately
20 seconds (do not hold the button for
longer than 30 seconds). This proce-
dure erases any previous settings for
all three channels and initializes the
memory.
If you later wish to program a second
and/or third hand-held transmitter to
the remaining two signal transmitter
buttons, do not repeat this step and be-
gin directly with step 3.
Step 3:
Hold the end of hand-held remote
control5 of the device you wish to
train approximately 2 to 5 in
(5 to12 cm) away from the signal trans-
mitter button (2, 3 or4) to be pro-
grammed, while keeping indicator
lamp1 in view.
Step 4:
Using both hands, simultaneously
press hand-held remote control
button6 and the desired signal trans-mitter button (2, 3 or4). Do not
release the buttons until step 5 is com-
pleted.
Indicator lamp1 will flash, first slowly
and then rapidly.
Step 5:
After indicator lamp1 changes from a
slow to a rapidly flashing light, release
the hand-held remote control button
and the signal transmitter button.
Step 6:
Press and hold the just-trained signal
transmitter button (2, 3 or4) and
observe indicator lamp1.If indicator lamp1 stays on
constantly, programming is complete
and your device should activate when
the respective signal transmitter
button (2, 3 or4) is pressed and re-
leased.
Step 7:
To program the remaining two signal
transmitter buttons, repeat the steps
above starting with step 3.
Rolling code programming
To train a garage door opener (or other
rolling code devices) with the rolling code
feature, follow these instructions after
completing the “Programming” portion
(steps 1 through 6) of this text. (A second
person may make the following training
procedures quicker and easier.)
iIndicator lamp1 flashes immediately the
first time the signal transmitter button is pro-
grammed. If this button has already been pro-
grammed, the indicator lamp will only start
flashing after 20 seconds.iIf indicator lamp1 flashes rapidly for about
2 seconds and then turns to a constant light,
continue with programming steps 8 through 12
as your garage door opener may be equipped
with the “rolling code” feature.

256 Controls in detail
Useful features
Step 8:
Locate “training” button on the garage
door opener motor head unit.
Exact location and color of the button
may vary by garage door opener brand.
Depending on manufacturer, the
“training” button may also be referred
to as “learn” or “smart” button. If there
is difficulty locating the transmitting
button, refer to the garage door opener
Operator’s Manual.
Step 9:
Press the “training” button on the ga-
rage door opener motor head unit.
The “training light” is activated.
You have 30 seconds to initiate the
following step.
Step 10:
Return to the vehicle and firmly press,
hold for 2 seconds and release the pro-
grammed signal transmitter button
(2, 3 or4).Step 11:
Press, hold for 2 seconds and release
same signal transmitter button a sec-
ond time to complete the training
process.
Step 12:
Confirm the garage door operation by
pressing the programmed signal trans-
mitter button (2, 3 or4).
Step 13:
To program the remaining two signal
transmitter buttons, repeat the steps
above starting with step 3.Gate operator/Canadian programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission
which may not be long enough for the
integrated signal transmitter to pick up the
signal during programming. Similar to this
Canadian law, some U.S. gate operators
are designed to “time-out” in the same
manner.
If you live in Canada or if you are having
difficulties programming a gate operator
(regardless of where you live) by using the
programming procedures, replace step 4
with the following:
Step 4:Press and hold the signal transmitter
button (2, 3 or4). Do not release
this button until it has been successful-
ly trained.
While still holding down the signal
transmitter button (2, 3 or4),
“cycle” your hand-held remote control
button6 as follows: Press and hold
iSome garage door openers (or other rolling
code equipped devices) may require you to
press, hold for 2 seconds and release the same
signal transmitter button a third time to com-
plete the training process.

258 Controls in detail
Useful features
Programming tips
If you are having difficulty programming
the integrated remote control, here are
some helpful tips:

Check the frequency of hand-held re-
mote control5 (typically located on
the reverse side of the remote). The in-
tegrated remote control is compatible
with radio-frequency devices operating
between 280-390 MHz.

Put a new battery in hand-held remote
control5. This will increase the likeli-
hood of the hand-held remote control
sending a faster and more accurate sig-
nal to the integrated remote control.

While performing step 3, hold
hand-held remote control5 at differ-
ent lengths and angles from the signal
transmitter button (2, 3 or4) you
are programming. Attempt varying an-
gles at the distance of 2 to 5 inches
(5 to 12 cm) away or the same angle at
varying distances.

If another hand-held remote control is
available for the same device, try the
programming steps again using that
other hand-held remote control. Make
sure new batteries are in the hand-held
remote control before beginning the
procedure.

Straighten the antenna wire from the
garage door opener assembly. This
may help improve transmitting and/or
receiving signals.
iCertain types of garage door openers are in-
compatible with the integrated remote control. If
you should experience further difficulties with
programming the integrated remote control,
contact an authorized Mercedes-Benz Center, or
call Mercedes-Benz Customer Assistance
Center (in the USA only) at
1-800-FOR-MERCedes, or Customer Service (in
Canada) at 1-800-387-0100.
iUSA only:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interfer-
ence, and
(2) this device must accept any interference re-
ceived, including interference that may
cause undesired operation.
Any unauthorized modification to this device
could void the user’s authority to operate the
equipment.
iCanada only:
This device complies with RSS-210 of Industry
Canada. Operation is subject to the following
two conditions:
(1) This device may not cause interference, and
(2) this device must accept any interference re-
ceived, including interference that may
cause undesired operation of the device.
Any unauthorized modification to this device
could void the user’s authority to operate the
equipment.

425 Index
Fog lamps 112
Message in display 350, 352
Replacing bulbs 368
Four wheel electronic traction system
(4MATIC) with ESP
®88
4MATIC 88
Front air bags 63
Front lamps see Headlamps
Front passenger front air bag 63
Messages in display 337–340
Front passenger front air bag off
indicator lamp 27, 68, 331, 332
Front seat head restraints see
Head restraints
FSS (Flexible Service System)
(Canada vehicles) 310
Fuel 271, 272, 413
Additives 413
Capacities, Fuel tank 411
Cruising range 415
E85 (Ethanol fuel) 411, 415
Filling the tank 271
Fuel filler flap and cap, Multifunction
display messages 326, 349
Fuel gauge 25
Fuel reserve warning lamp 328Requirements, Octane rating 414
Switching (Flexible fuel vehicle) 415
Technical data 411, 413
Fuel consumption statistics
From start 144
Since last reset 145
Fuel filler flap 271
Fuel reserve warning lamp 25
Fuel tank
Capacity 411
Filler flap 271
Fuels, coolants, lubricants etc.
Capacities 409
Fuses 391
Fuse box (main) in
passenger compartment 392
Fuse box in engine compartment 392
Fuse box in trunk 394
Fuse extractor 394
Replacing 391G
Garage door opener* 253
Gasoline also see Fuel
Gasoline see Fuel
GAWR 305
Gear range
Automatic transmission 156
Limiting 156
Shifting into optimal 159
Gear selector lever 46, 47, 150, 151
Cleaning 319
Gearshift pattern 151
Lock 47
Position 152, 153
Position,
Automatic transmission* 121
Shifting procedure 152
Unlocking in an emergency 363
Global locking/unlocking see Key
Glove box 237
Good visibility 160
Gross Axle Weight Rating see GAWR
Gross Vehicle Weight Rating see GVWR
Gross Vehicle Weight see GVW
GVW 305
GVWR 305