technical data MERCEDES-BENZ C55AMG 2006 W203 Owner's Guide

437 Technical data
Fuels, coolants, lubricants, etc.
Engine oils
Engine oils are specifically tested for their
suitability in our engines and durability for
our service intervals. Therefore, only use
approved engine oils and oil filters
required for vehicles with Maintenance
System (U.S. vehicles) or FSS (Canada
vehicles). For a listing of approved engine
oils and oil filters, refer to the Factory Ap-
proved Service Products pamphlet, or con-
tact an authorized Mercedes-Benz Center.
Engine oil additives
Do not blend oil additives with engine oil.
They may damage the engine.
Damage or malfunctions resulting from
blending oil additives are not covered by
the Mercedes-Benz Limited Warranty.
Air conditioning refrigerant
R-134a (HFC) refrigerant and special PAG
lubricating oil are used in the air
conditioning system.
Never use R-12 (CFC) or mineral-based
lubricating oil. Otherwise damage to the
system will occur.
Brake fluid
During vehicle operation, the boiling point
of the brake fluid is continuously reduced
through the absorption of moisture from
the atmosphere.
Only brake fluid approved by
Mercedes-Benz is recommended. An
authorized Mercedes-Benz Center will
provide you with additional information.
!
Using engine oils and oil filters of
specification other than those express-
ly required for the Maintenance System
(U.S. vehicles) or FSS (Canada vehi-
cles), or changing of oil and oil filter at
change intervals longer than those
called for by the Maintenance System
(U.S. vehicles) or FSS (Canada vehi-
cles) will result in engine damage not
covered by the Mercedes-Benz Limited
Warranty.
Please follow Maintenance System
(U.S. vehicles) or FSS (Canada vehi-
cles) recommendations for scheduled
oil changes. Failure to do so will result
in engine damage not covered by the
Mercedes-Benz Limited Warranty.
Warning!G
Under extremely strenuous operating condi-
tions, this moisture content can lead to the
formation of bubbles in the system, thus re-
ducing the system’s efficiency.
Therefore, the brake fluid must be replaced
regularly. Refer to your vehicle’s Mainte-
nance Booklet for replacement interval.

438 Technical data
Fuels, coolants, lubricants, etc.
Premium unleaded gasolineGasoline additives
A major concern among engine
manufacturers is carbon build-up caused
by gasoline. Mercedes-Benz recommends
only the use of quality gasoline containing
additives that prevent the build-up of
carbon deposits.
After an extended period of using fuels
without such additives, carbon deposits
can build up especially on the intake valves
and in the combustion area, leading to
engine performance problems such as:

Warm-up hesitation

Unstable idle

Knocking/pinging

Misfire

Power loss
Warning!G
Gasoline is highly flammable and poisonous.
It burns violently and can cause serious
injury. Whenever you are around gasoline,
avoid inhaling fumes and skin contact, extin-
guish all smoking materials. Never allow
sparks, flame or smoking materials near
gasoline!
!
To maintain the engine’s durability and
performance, premium unleaded gaso-
line must be used. If premium unleaded
is not available and low octane fuel is
used, follow these precautions:

Have the fuel tank only partially
filled with unleaded regular and fill
up with premium unleaded as soon
as possible.

Avoid full throttle driving and abrupt
acceleration.

Do not exceed an engine speed of
3 000 rpm if the vehicle is loaded
with a light load such as two
persons and no luggage.

Do not exceed2/3 of maximum
accelerator pedal position if the
vehicle is fully loaded or operating
in mountainous terrain.

439 Technical data
Fuels, coolants, lubricants, etc.
In areas where carbon deposits may be
encountered due to lack of availability of
gasolines which contain these additives,
Mercedes-Benz recommends the use of
additives approved by us for use on
Mercedes-Benz vehicles. Refer to Factory
Approved Service Products pamphlet for a
listing of approved product(s). Follow
directions on product label.
Do not blend other fuel additives with fuel.
This only results in unnecessary cost and
may be harmful to engine operation.
Damage or malfunction resulting from
poor fuel quality or from blending
additional fuel additives other than those
tested and approved by us for use on
Mercedes-Benz vehicles listed in the
Factory Approved Service Products
pamphlet are not covered by the
Mercedes-Benz Limited Warranty. Fuel requirements
Only use premium unleaded fuel:

The octane number (posted at the
p um p) m us t be 91 mi n. It i s an a vera ge
of both the Research (R) octane num-
ber and the Motor (M) octane number:
(R+M)/2. This is also known as the
ANTI-KNOCK INDEX.
Unleaded gasoline containing oxygenates
such as ethanol, IPA, IBA and TBA can be
used provided the ratio of any one of these
oxygenates to gasoline does not
exceed 10%; MTBE must not exceed 15%.
The ratio of methanol to gasoline must not
exceed 3% plus additional cosolvents.
Using mixtures of ethanol and methanol is
not allowed. Gasohol, which contains 10%
ethanol and 90% unleaded gasoline, can
be used.
These blends must also meet all other fuel
requirements, such as resistance to spark
knock, boiling range, vapor pressure, etc.
Coolants
The engine coolant is a mixture of water
and anticorrosion/antifreeze, which
provides:

Corrosion protection

Freeze protection

Boiling protection (by increasing the
boiling point)
The cooling system was filled at the factory
with a coolant providing freeze protection
to approximately -22°F (-30°C) and
corrosion protection.
If the antifreeze mixture is effective
to -22°F (-30°C), the boiling point of the
coolant in the pressurized cooling system
is reached at approx. 266°F (130°C).

440 Technical data
Fuels, coolants, lubricants, etc.
The coolant solution must be used
year-round to provide the necessary corro-
sion protection and increase boil-over
protection. Refer to Maintenance Booklet
for replacement interval.
Coolant system design and coolant used
determine the replacement interval. The
replacement interval published in the
Maintenance Booklet is only applicable
if MB 325.0 anticorrosion/antifreeze
solution or other Mercedes-Benz approved
products of equal specification (see
Factory Approved Service Products
pamphlet) are used to renew the coolant
concentration or bring it back up to the
proper level.
To provide important corrosion protection,
the solution must be at least 45%
anticorrosion/antifreeze [equivalent to
freeze protection to approx. -22°F
(-30°C)]. If you use a solution that is more than 55%
anticorrosion/antifreeze [freeze
protection to approx. -49°F (-45°C)], the
engine temperature will increase due to
the lower heat transfer capability of the
solution. Therefore, do not use more than
this amount of anticorrosion/antifreeze.
If the coolant level is low, water and
MB 325.0 anticorrosion/antifreeze should
be used to bring it up to the proper level
(have cooling system checked for signs of
leakage). Please make sure the mixture is
in accordance with label instructions.
The water in the cooling system must meet
minimum requirements, which are usually
satisfied by normal drinking water. If you
are not sure about the water quality,
consult an authorized Mercedes-Benz
Center.Anticorrosion/antifreeze
Your vehicle contains a number of
aluminum parts. The use of aluminum
components in motor vehicle engines
necessitates that anticorrosion/antifreeze
coolant used in such engines be specifi-
cally formulated to protect the aluminum
parts.
Failure to use such anticorrosion/anti-
freeze coolant will result in a significantly
shortened service life.
Therefore, the following product is strongly
recommended for use in your vehicle:
Mercedes-Benz 325.0
anticorrosion/antifreeze agent.
Before the start of the winter season (or
once a year in hot southern regions), you
should have the anticorrosion/antifreeze
concentration checked. The coolant is also
regularly checked each time you bring your
vehicle to an authorized Mercedes-Benz
Center for service.

441 Technical data
Fuels, coolants, lubricants, etc.
Anticorrosion/antifreeze quantity
ModelApprox. freeze protection
–35°F (–37°C)–49°F (–45°C)
C55AMG6.4 US qt (6.0 l)7.0 US qt (6.6 l)

442 Technical data
Fuels, coolants, lubricants, etc.
Windshield washer and headlamp
cleaning system*
Both the windshield washer and headlamp
cleaning system* are supplied from the
windshield washer fluid reservoir.
The washer fluid reservoir has a capacity of
approx.:

3.2 US qt (3.0 l) in vehicles without
headlamp cleaning system*

6.4 US qt (6.0 l) in vehicles with
headlamp cleaning system*
Refill the reservoir with MB Windshield
Washer Concentrate “MB SummerFit”
and water (or concentrate and com-
mercially available premixed wind-
shield washer solvent/antifreeze,
depending on ambient temperatures).Windshield and headlamp washer fluid
mixing ratio
For temperatures above freezing point, use
MB Windshield Washer Concentrate
“MB SummerFit” and water:

1 part “MB SummerFit” to 100 parts
water
(1.34floz [40ml]“MBSummerFit” to
1 gallon [4.0 l] water)
For temperatures below freezing point, use
MB Windshield Washer Concentrate
“MB SummerFit” and commercially avail-
able premixed windshield washer sol-
vent/antifreeze:

1 part “MB SummerFit” to 100 parts
solvent
(1.34floz [40ml]“MBSummerFit” to
1 gallon [4.0 l] solvent)
Warning!G
Washer solvent/antifreeze is highly flamma-
ble. Do not spill washer solvent/antifreeze
on hot engine parts, because it may ignite
and burn. You could be seriously burned.

444 Technical terms
CAN system
(C
ontroller Area Network)
Data bus network serving to control
vehicle functions such as door locking
or windshield wiping depending on
vehicle settings and/or ambient
conditions.
Cockpit
All instruments, switches, buttons and
indicator/warning lamps in the
passenger compartment needed for
vehicle operation and monitoring.
Cold tire inflation pressure
(
page 331)
Collapsible tire
An especially compact spare tire that
must be inflated with a provided air
pump before using. It should only be
used to bring the vehicle to the nearest
service station.COMAND*
(C
ockpit Management and Data
System)
Information and operating center for
vehicle sound and communications
systems, including the radio and the
navigation system, as well as other
optional equipment (CD changer*,
telephone*, etc.).
Control system
The control system is used to call up
vehicle information and to change
component settings. Information and
messages appear in the multifunction
display. The driver uses the buttons on
the multifunction steering wheel to
navigate through the system and to
adjust settings.
Cruise control
Driving convenience system that
automatically maintains the vehicle
speed set by the driver.
Curb weight
(
page 332)DOT
(D
epartment of Transportation)
(
page 332)
Engine number
The number set by the manufacturer
and placed on the cylinder block to
uniquely identify each engine
produced.
Engine oil viscosity
Measurement for the inner friction
(viscosity) of the oil at different temper-
atures. The higher the temperature an
oil can tolerate without becoming thin,
or the lower the temperature it can
tolerate without becoming viscous, the
better the viscosity.
ESP
®
(Electronic Stability Program)
Improves vehicle handling and
directional stability.

453 Index
Driving
Abroad 290
Hydroplaning 287
In winter 288
Instructions 42, 283
Problems 52
Safety systems 82
Systems 245
Through standing water 289
Driving safety systems
ABS 82
BAS 84
ESP
®84
E
Easy-entry/exit feature 39, 148
Electrical fuses see Fuses
Electrical outlet 263
Electrical system, Technical data 434
Electronic Stability Program see ESP
®
Emergency calls
911 calls 235
Tele Aid* calls 266, 267, 271
Emergency operation
(Limp-Home Mode) 168Emergency operations
Gear selector lever, Unlocking 388
Locking/unlocking the vehicle 386
Power tilt/sliding sunroof*,
Manual operation 389
Remote door unlock 272
Trunk lid, Releasing from inside 102
Trunk lid, Unlocking 387
Emergency Tensioning Device see ETD
Emergency, in case of
Battery, Jump starting 415
First aid kit 350, 380
Flat tire, Changing 404
Fuses 420
Hazard warning flasher 119
Instrument cluster,
Indicator lamps 350–356
Roadside Assistance 12, 268
Towing the vehicle 417
Emission control 291
Information label 426
System warranties 10Engine
Belt layout 427
Block heater (Canada only) 337
Brake-in recommendations 282
Cleaning 343
Compartment 297
Malfunction indicator lamp 25, 352
Maximum engine speed 428
Number 426
Starting 46
Technical data 428
Turning 56
Engine coolant see coolant
Engine number 444
Engine oil 298, 437
Adding 300
Additives 437
Changing 436
Checking level 299
Consumption 298
Display messages 299
Filler neck 301
Messages in display 299, 371, 372
Recommended engine and
oil filter 371
Viscosity 444

454 Index
ESP®84, 444
Messages in display 361–362
Warning lamp 25, 354
ETD 70, 445
Safety guidelines 64
Exterior lamp switch 48, 114
Exterior rear view mirrors 40
Parking position 170
F
Fahrenheit see Temperature display
mode 137
Filler neck, Engine oil 301
First aid kit 380
Flat tire 404
Jacking up the vehicle 405
Lowering the vehicle 410
Mounting the spare wheel 404
Preparing the vehicle 404
Spare wheel with collapsible tire 383
Flexible Service System see FSSFluids
Automatic transmission fluid 301,
436
Brake fluid 295, 437
Capacities 436
Engine coolant 295, 439
Engine oil 298, 437
Power steering fluid 436
Windshield washer and headlamp
cleaning system* 304, 442
Fog lamps 117, 118
Message in display 374, 376
Replacing bulbs 395, 396
Front air bags 65
Front lamps see Headlamps
Front passenger front air bag 65
Front passenger front air bag off indicator
lamp 27, 75, 357
Front seat head restraints see Head
restraints 106
FSS (Flexible Service System) (Canada
vehicles) 338, 445Fuel 293, 438
Additives 438
Capacities, Fuel tank 436
Filling the tank 293
Fuel filler flap and cap, Multifunction
display messages 353, 373
Fuel gauge 25
Fuel reserve warning lamp 354
Requirements, Octane rating 439
Technical data 436, 438
Fuel consumption statistics
After start 150
Since last reset 151
Fuel filler flap 293
Fuel reserve warning lamp 25
Fuel tank
Capacity 436
Filler flap 293
Fuels, coolants, lubricants etc.
Capacities 436

457 Index
L
Labels 426
Certification 426
Emission control information 426
Emission control vacuum line
routing 426
Lamp sensor
Message in display 375
Lamps, exterior 395, 396
Light sensor 375
Messages in display 374, 375, 376,
377
Lamps, indicator and warning
ABS 25, 350
Battery (SmartKey) 96
Brakes 25, 351
Engine diagnostics 352, 356
Engine malfunction 25, 352–353
ESP
®25, 354
Fog lamps 114
Front passenger front air bag off 27,
66
Fuel reserve 25, 354
High beam headlamps 25
Instrument cluster 350, 356
Low beam headlamps 25Maintenance service indicator 338
Rear fog lamp 114
Seat belt telltale 25
SRS 25, 61, 356
Turn signals 25
Language, Setting 138
LATCH-type child seat anchors see
Children in the vehicle
Leather upholstery, Cleaning and
care of 347
License plate lamps
Messages in display 375
Replacing bulbs 396
Light alloy wheels
Cleaning 346
Technical data 431, 432
Light sensor see Lamp sensor
Lighter see Cigarette lighter
Lighting
Parking lamps 114
Lighting, Exterior and interior 114
Limp-Home Mode 168
Loading see Vehicle loading
Loading terminology 331
Loading the vehicle 308
Locator lighting 117, 145Locking knob 445
Loss of keys 98
Loss of Service and Warranty Information
Booklet 425
Low beam headlamps
Indicator lamp 25
Messages in display 375, 376
Replacing bulbs 395, 398
Switching on 48
Lubricants 436
Technical data 436
Lumbar support* 109
M
Main dimensions 435
Main fuse box
In passenger compartment 421
Main odometer 125