navigation system MERCEDES-BENZ CL-Class 2005 C215 Comand Manual

136 NavigationDestination input
Press H, h, g, G, F, f to
move the cross-hairs.
The direction of movement of the
buttons depends on the map direction
selected (
page 153).

2D North Up, 2D Heading Up:
Press F and f to move the
cross-hairs diagonally.

Bird’s-Eye View:
Use H and h to turn the map
round the vertical axis of the cross-
hairs.
Press g or G to move your
position on the map forward or
backward.This allows you to select your destination.

Release the button.
If the system is able to assign a street
name to the selected location, it is
displayed on the status bar.
In this example:
NEWPORT
RD

Press E.
The system uses the point at the center
of the cross-hairs as destination.
Route guidance will begin.
iIf you press the
Back
soft key, your
selection will be discarded. The system
then uses the data of the previous
destination.

139 Navigation
Route guidance

Route guidance
Route guidance can be started if the
destination input is complete and Start
Route Guidance is displayed at the bottom
of the main area. 
Press E.
Route calculation and route guidance
begins. Route calculation can take some time,
depending on the distance to the
destination.
During route calculation,
CALC RTE
and an
arrow pointing towards the destination are
displayed.
Route guidance begins when route
calculation is complete.
The system will calculate a new route
during active route guidance if the driver
does not follow the route guidance.
NEW RTE
is displayed during recalculation.
The arrow is not filled out.After route calculation, the system assists
route guidance using pictorial displays
(
page 140) and voice instructions.
Repeating current voice instructions
If you have not understood a navigation
announcement, you can at any time have a
current announcement repeated.

Press j.
The current navigation announcement
is repeated.
Starting route guidance
Route calculationRecalculating an existing route
Voice instructionsWarning
G
Voice instructions are intended to direct you
while driving without diverting your attenti-
on from the road and driving.
Always use this feature instead of consulting
the map display for directions. Consulting
the map displays for directions may cause
you to divert your attention from driving and
increase the risk of an accident.

140 NavigationRoute guidanceMuting current voice instructions
Press J.
The current announcement is stopped.
You will hear the next navigation
announcement normally.
Switching voice instructions On/Off
Switching off

During a navigation announcement
press J for 2 seconds.
You will hear a confirmation beep if the
beep tones option was activated in the
system settings (
page 201).
The message
Voice Announcements
Muted
will appear briefly. Further route
guidance takes place using only the
symbols in the display. If a new route
guidance cycle is started, the
announcements are automatically
switched on again.
Switching on again

Press j.The navigation displays are only visible
while route guidance is active.
To switch to the navigation display from
another display, e.g. from CD operation:

Press b or c.
Two examples are shown below:
Display example 1:The road you are currently driving on is
shown on the status bar, in this case
I-90
.
The indication
120 mi
is the distance to
the next driving maneuver.
If the GPS position display (
page 154) is
active, the GPS data are shown instead of
the street name.
Navigation displays
iUsing the multifunction steering wheel
buttons, the display unit can be
changed between km or miles (see
your vehicle’s Operator’s Manual). 
When the display unit is set to
miles, the COMAND will indicate
distances in miles (mi) or feet (ft).

When the display unit is set to km,
the COMAND will indicate
distances in kilometers (km) or
meters (m).

141 Navigation
Route guidance
Important map symbols:
Current vehicle location and direction
of travel y
If the map orientation
2D Heading Up
(page 153) is chosen, the arrow will
always point upward.

The remaining route section is
highlighted in blue color.
Display example 2:On the right side of the display, the symbol
for the next driving maneuver is indicated
(here: right turn).
On the very right side next to turn symbol
is the distance bar. It indicates the
distance to the next driving maneuver
(here: 300 ft).
The status bar shows the name of the
street after the driving maneuver, if
available, here:
PARK AVE
The destination is marked with a flag $ on
the map, an intermediate destination is
marked with a flag showing the letter
S.
Altering the map scale
The current map scale is indicated on the
left side of the status bar.

Press any soft key.
The soft key displays appear.
iThe colored highlight only appears
when the system has completed the
route calculation.
iUsing the multifunction steering wheel
buttons, the display unit can be
changed between km or miles (see
your vehicle’s Operator’s Manual). 
When the display unit is set to
miles, the COMAND will indicate
distances in miles (mi) or feet (ft).

When the display unit is set to km,
the COMAND will indicate
distances in kilometers (km) or
meters (m).
iIf no other action is taken within
approx. 8 seconds, the soft key
displays will disappear again.

145 Navigation
During route guidance
Available soft keys
Route
soft key:
Brings you to the route display on the
map.

Mode
soft key:
Brings you to the route mode selection
menu (page 120).

Setting
soft key:
Brings you to the audio settings for the
navigation announcements
(
page 121).Displaying the route on the map

In the Info menu (
page 144), press
the
Route
soft key.
The map will appear. The route ahead
is blue-colored.
The destination is marked with a flag $
on the map, a stopover destination is
marked with a flag showing the letter
S.
Displaying the route list

In the Info menu (
page 144), press
the
Route
soft key.
The route appears on the map.

Press the
List
soft key.
The list of the remaining roads/route
sections appears.
The road currently travelled on is at the
top of the list.

Press G or g to scroll through the
list.
Use the
Page
V and
Page
v soft keys
to display the next or previous page.
iIf a stopover destination has been
entered:
The estimated time of arrival and the
remaining distance to the destination
are displayed.
When the stopover destination is
reached, the system calculates the
route to the main destination and
indicates estimated time of arrival and
remaining distance.
iDepending on the distance to the
destination, it may take some time
before the route display appears.
iDepending on the distance to the
destination, it may take a few moments
before the route list is completed.
The list will only be complete when the
route is completely calculated. This is
indicated by the word
Destination
in
front of the last list entry.

146 NavigationDuring route guidanceWith the via function you can influence
how the route is calculated.
Example:
You wish to travel from Chicago to New
York. You can use the via function to define
whether the route will lead via Cleveland or
Pittsburgh.
In the Info menu (
page 144), press
the
Route
soft key.
The route is shown on the map.

Press the
Via
soft key.If the via function is not yet active, you may
now select a via route.
If the via function is already active, the
message
Via Already Active
will
appear. You can delete (
page 147) or
change (
page 147) the via route.
Selecting a via route
You can select one via route at a time.

Press G or g to select a list entry.

Press E.
The system calculates the new route.
Via function (soft key via)iThe
Via
soft key has no function if the
route cannot offer any via routes.
iThe selection list always refers to the
currently active route.
Example:
You have entered a main and a
stopover destination. First, the system
will calculate your route to the stopover
destination, so that route is the active
route.
The selection list only shows possible
via routes to the stopover destination.

147 Navigation
During route guidance
Deleting the active via route 
Press g to select option
Delete
Active Via
.

Press E.
The system deletes the via route and
recalculates the route to the
destination.Changing the active via route

Press g to select option
Change
Active Via
.

Press E.
The list for selecting another via route
appears.

Use G or g to select the desired via
route.

Press E.
The system recalculates the route.The detour function blocks a route section
ahead. If possible, the system will
calculate a detour. You can adjust the
length of the route section to be blocked.
Switching on

Activate the soft key display (
page 144).

Press the
Detour
soft key.
iIf you enter a new destination, the sys-
tem will automatically delete any active
via route.
Selecting a detouriIf the system does not allow you to
block a route section, the message
No
Detour Possible
is displayed.
Traffic jams are identified by the driver,
not by the COMAND. The detour
function may also be possible if the
vehicle is traveling on a road that does
not appear on the DVD.
iIf you have already placed a block on a
route section,
Detour
appears written
in black. A menu will appear instead of
the map (
page 148).

148 NavigationDuring route guidanceYou can now enter the length of the route
section to be blocked.
Press the
More
soft key until the
desired length is set.

Press the
Less
soft key to reduce the
length of the traffic jam.

Press E.
The system calculates a new route
around the blocked route section.Switching off

Activate the soft key display by
pressing any soft key (
page 144).

Press the
Detour
soft key.

Press g to select
Delete Detour
.

Press E.
The blocked route section is deleted.
The system calculates the new route.Changing the blocked route section

Activate the soft key display
(page 144).

Press the
Detour
soft key.

Use G to select item
Reset Detour
.

Press E.
You can now change the length of the
route section to be blocked.

Press the
More
soft key until the
desired length is set.

Press the
Less
soft key to reduce the
length of the blocked route section.

Press E.
The system calculates a new route
around the blocked route section.
iThe route directly in front of the current
position can be blocked in the range of
0 to 6.2 miles.

149 Navigation
During route guidance
This function allows you to select an
intermediate destination while route
guidance is active. A stopover destination
may be a gas station or a restaurant or any
other place. When the stopover
destination is reached, the system
calculates the route to the main
destination.
Entering a stopover destination
Activate the soft key display
(page 144).

Press the
St-over
soft key.
The map is displayed in full view.Available soft keys

soft key:
Shows a list of Mercedes-Benz Centers
near your location.

soft key:
Shows a list of filling stations around
you.

soft key:
Shows a list of parkings and multi-
storey car parks around you.

soft key:
Shows a list of restaurants around you.

soft key:
Shows a list of hospitals around you.

More
soft key:
If you press this soft key, the
Navigation main menu will appear.
Enter Stopover
will appear on the
status bar.
You can now enter an stopover
destination by

selecting one from the destination
memory (
page 156)

typing one in the Destination Entry
menu (
page 125)

selecting one in the
Last
destinations
memory
(
page 155)

selecting a POI (
page 160)
Stopover function

150 NavigationDuring route guidance
Press a soft key, e.g. .

Press E.
A list of restaurants near your location
is displayed.The arrows left from the entries indicate
the direction of the destination. The
distances indicated are straight line
distances to the destination.

Press G or g to select a destination
from the list.

Press the
Details
soft key if required.
Details on the destination are shown.

Name
soft key
:
Brings you to name input of a stopover
destination (
page 193).

Sort
soft key
:
Sorts list entries either by increasing
distance or alphabetically.

After you have selected a destination,
press E.
The Start Route Guidance menu will
appear (
page 139).

Press E.
The system calculates the route to the
selected stopover destination.Deleting or replacing a stopover
destination

Activate the soft key display
(page 144).

Press the
St-over
soft key.
The menu for deleting or changing a
stopover destination will appear.
iPrior to this, a list may be displayed in
which you can select the desired
category, e.g.
Barbecue/Southern
,
pressing G or g.