navigation system MERCEDES-BENZ CL-Class 2005 C215 Comand Manual

187 Service
Address book
If the address book entry offers
appropriate data, it may be used in other
system modes such as telephone and
navigation.
Press H, h, g or G to select the
desired entry (
page 177).

Press E.
or

In the detail view (
page 178), press
E longer than 2 seconds.
You will hear a confirmation beep if the
beep tones option was activated in the
system settings (
page 201).
The selection menu appears.
Selections appearing will depend on
the data available for a given entry. Using an address book entry to dial a
number
You can have a phone number dialed which
is saved in the address book.

Press g or G to select a phone
number.

Press E.
Dialing will begin. You can then make
your telephone call.
You will find more information in
chapter “Telephone”.Starting route guidance to an address
book entry
You can transfer an address to the
navigation system and start route
guidance.
f
Using an address book entry
in other system modes
iThis function is only available for
addresses which are saved in the
navigation system’s destination
memory (
page 155). The COMAND
saves addresses not only in the
destination memory, but at the same
time in the address book.

188 ServiceAddress book
Press g or G to select an entry
which allows route guidance
(navigation).

Press E.
The system changes to the navigation
system and calculates the route.
You will find more information in
chapter “Navigation”.iThe route is calculated with or without
traffic routes selected for the
destination (
page 120).

191 Service
Tele Aid*
If the Tele Aid system could not establish a
voice connection to a Mercedes-Benz
Roadside Center (e.g. the relevant cellular
phone network is not available). The
message
Call failed
appears.Terminating the connection
Roadside Assistance calls can be
terminated using the ì button on the
multifunctional steering wheel or the K
key on COMAND. The call can also be
terminated by the Roadside Assistance
Center.
The COMAND reverts to the system last
active before a Tele Aid call was initiated.Pressing the ¡ button, a call to the
Mercedes-Benz Customer Assistance
Center will be initiated. Information
regarding the operation of your vehicle, the
nearest authorized Mercedes-Benz Center
or Mercedes-Benz USA products and
services is available to you.
Refer to your vehicle Operator’s Manual for
additional information.
After initiating an Information call, the
message
Connecting Call
will appear
on display. The system is then establishing
a connection to the Mercedes-Benz
Customer Assistance Center. All audio
sources are muted.
If the connection is established, the
message
Call Connected
will appear
and a voice connection between the
Roadside Assistance Center and the
vehicle occupants is established soon
after.
iDuring an active Roadside Assistance
call, switching to another application
(e.g. Navigation*) is possible.
Information call

192 ServiceTele Aid*If the Tele Aid system could not establish a
voice connection to the Mercedes-Benz
Customer Assistance Center (e.g. the
relevant cellular phone network is not
available). The message
Call failed

appears.Terminating the connection
Information calls can be terminated using
the ì button on the multifunctional
steering wheel or the K key on
COMAND. The call can also be terminated
by the Customer Assistance Center.
The COMAND reverts to the system last
active before a Tele Aid call was initiated.For the Tele Aid services Remote Door
Unlock and Stolen Vehicle Recovery
please refer to your vehicle Operator’s
Manual for information.
iDuring an active Information call,
switching to another application (e.g.
Navigation*) is possible.
Remote Door Unlock and Stolen
Vehicle Recovery

198 System settingsSystem settings

System settings
Press C.

In the Service main menu, press the System
soft key.
System settings menu
In the System settings menu you can:
set date and time

switch verification and notification
tones on and off (
page 201)

adjust display settings (
page 201)

activate and deactivate the Voice
control system* help window
(page 203)

start Voice control system*
individualization (
page 203)

reset system settings (
page 204)Setting date
Activating the System settings
menu
Setting the date/time iExact settings of date, time and current
time zone allow you:
correct navigation for
routes with time-dependent traffic
guidance

correct calculation of the expected
time of arrival
iIf time/date information is transmitted
by the GPS, you cannot set the date.
A satellite symbol is displayed on the
status bar if the system uses GPS data.

205 Glossary
Audio source
This includes the systems radio, CD
(CD drive in the control unit, CD chan-
ger*), MP3-CD and DVD (only audible).
Balance
Defines sound-center left/right.
Bird’s-eye view
The map is shown in three dimensions
with sky and horizon.
COMAND
(Co
ckpit Man
agement and D
ata Sys-
tem)
Information and operating center for
vehicle sound and communications
systems, including the radio and
CD/DVD player, as well as for other op-
tional equipment (CD changer*, tele-
phone*, etc.).DVD
(D
igital V
ersatile D
isc)
Digital storage medium for storing lar-
ge amounts of data.
Emergency call
This function places a call to a local
911 provider. It does not initiate a
->Tele Aid* call. Please note that the
911 emergency call system is a public
service. Using it without due cause is a
criminal offense.
Fader
Defines sound-center front/back.
GPS
(G
lobal P
ositioning S
ystem)
Satellite-based system for relaying
geographic location information to and
from vehicles equipped with special re-
ceivers. Employs DVD digital maps for
navigation.Heading Up
Dynamic map alignment, map is dis-
played facing driving direction pointing
up.
Navigation DVD
Contains all the destination addresses
(town, road, intersection, house num-
ber, special destinations) and the digi-
tal map material for a country or a
region for destination entry, route cal-
culation and destination guidance.
North Up
The map is displayed facing north du-
ring route guidance.
Provider
is the network operator who makes
available (provides) telephone services

206 GlossaryRoaming
For this function, the telephone uses
the network of a contract partner.
There are home type and non- home
type systems. The Roaming indicator in
the COMAND display indicates that a
call is being made using a non-home
type system.
Service source
This includes the systems telephone*,
navigation (voice output during desti-
nation guidance) and ->Voice control
system
SMS
(S
hort M
essage S
ervice)
With this function you can receive, read
and delete short text messages (if SMS
service is provided by your carrier)Soft keys
Keys that activate different functions.
Function of key depends on the selec-
ted operating mode.
Surround
Playback method resulting in an impro-
ved spatial listening experience com-
pared to conventional stereo playback.
Tele Aid*
(Tele
matic A
larm I
dentification on D
e-
mand)
The Tele Aid system consists of three
types of response: automatic and ma-
nual emergency, roadside assistance,
and information. Tele Aid is initially ac-
tivated by completing a subscriber
agreement and placing an acquain-
tance call. Refer also to the vehicle op-
erating instructions.The Tele Aid system is operational pro-
vided that the vehicle’s battery is char-
ged, properly connected, not damaged,
and cellular and GPS coverage is avai-
lable.
Unlock code
Your unlock code prevents unauthori-
zed persons from using your telephone.
The unlock code is a number string,
which you have to enter when switch-
ing on the telephone.
Voice output
During a trip, apart from visual informa-
tions (symbol or map displays),
COMAND also provides all of the
necessary spoken route information
via voice output.

209 Index
A
Accepting
call 97
Activating
Address book menu 176
Destination Entry menu 124
destination memory 158
Last destinations 155
Navigation main menu 118
Service main menu 168
Settings menu (DVD operation) 71
sound functions* 32
System settings menu 198
ACTIVATING TELEPHONE. PLEASE
WAIT. 91
Active call 102
Adding
note 180
Address book 176
changing an address book entry 179
deleting entry 186details on a mobile phone internal
memory entry 182
details on an address book entry 178
exporting an entry 181
importing a mobile phone internal
memory entry 183
new entry 185
selecting an entry 177
using an entry in other system
modes 187
Adjusting
bass and treble 121
bass or treble control 31
brightness, contrast, color (DVD
operation) 74
display brightness 202
volume 28
Altering
map scale 141
Automatic map toggling 154
Automatic station scan 39B
Balance 121
Balance control 29
Bass 30
Begin dialing 99
C
CALC RTE 139
CALL CONNECTED 189
Calling up
main menus 24
Cancelling
route guidance 143
CD
loading
into the CD/DVD drive 47
REPEAT TRACK 53, 54
TRACK MIX 54
track select 50
CD changer*
CD MIX 54
REPEAT CD 54

211 Index
destination address 125
house number 132
intersection 131
name or number in the phone
book 107
parking 133
PIN code 95
PUK 96
street 129
telephone number 98
ENTRY IMPORTED TO ADDRESS
BOOK 183
ERROR OCCURED WHILE SAVING
DATA 173, 174
Exporting
address book entry 181
F
Fader 29, 121
Frequency band 38
Frequency range 38G
GPS 115
H
Hands-free microphone
switching on/off 103
I
Important notes
Telephone 88
Importing
mobile phone internal memory
entry 183
Incoming call 97
L
Loading
CD
into the CD changer* 47
into the CD/DVD drive 47
DVD
into the CD/DVD drive 65
MP3-CD 56
into the CD/DVD drive 56Loading/ejecting
navigation DVD 115
M
Making
display settings 201
Map orientation
2D Heading Up 142
2D North Up 142
Memory
destination memory 156
last destinations 155
Memory functions
radio operation 40
Menu
functions 25
main area 24
soft key sections 24
status bar 24
Menu display 24
Menu system 24