warning MERCEDES-BENZ CL-CLASS 2007 Owners Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2007, Model line: CL-CLASS, Model: MERCEDES-BENZ CL-CLASS 2007Pages: 723, PDF Size: 19.87 MB
Page 362 of 723
361 Controls in detail
Fastening the seat belts
1Belt outlet
2Latch plate
3Buckle
4Release button
Pull the seat belt smoothly from the
seat belt outlet 1.
Place the shoulder portion of the belt
across the top of your shoulder and the
lap portion across your hips.
Push latch plate2 into buckle3 until
it clicks.
If necessary, tighten the lap portion to
a snug fit by pulling shoulder portion
up.
To release the seat belt, press release
button4 and guide latch plate back to
belt outlet.
Warning!G
Read and observe the additional warning no-
tices printed in the “Safety and Security”
section (
page 40).
ProCarManuals.com
Page 363 of 723
362 Controls in detail
Fastening the seat belts
Proper use of seat belts
Do not twist the belt when fastening.
Adjust seat belt so that the shoulder
portion is located as close as possible
to the middle of the shoulder (it should
not touch the neck). Never pass the
shoulder portion of the belt under your
arm.
Position the lap belt as low as possible
on your hips (over hip joint) and not
across the abdomen.
Place the seat backrest in a nearly up-
right position.
Never use a seat belt for more than one
person at a time.
Do not fasten a seat belt around a per-
son and another object at the same
time. When using a seat belt to secure
infant restraint, toddler restraint, or
booster seat always follow the child
seat manufacturer’s instructions.
Check your seat belt during travel to
make sure that it is properly posi-
tioned.
Make sure the seat belt is always fitted
snugly. Take special care of this when
wearing loose clothing.For more information, see “Seat belts”
(
page 52).
Seat belt height adjustment
The vehicle automatically adjusts the seat
belt height for the driver’s and front pas-
senger’s seats as well as for the rear outer
seats. Comply with the instructions on how
to properly fasten a seat belt
(
page 360).
Warning!G
Do not pass belts over sharp edges. They
could tear.
Do not allow the belt to get caught in the
door or in the seat adjustment mechanism.
This could damage the belt.
Never attempt to make modifications to
seat belts. This could impair the effective-
ness of the belts.
Do not bleach or dye seat belts as this may
severely weaken them. In a crash, they may
not be able to provide adequate protection.
Damaged seat belts or belts that were highly
stressed in an accident must be replaced.
Contact an authorized Mercedes-Benz
Center.
ProCarManuals.com
Page 364 of 723
363 Controls in detail
Lighting
Lighting
Exterior lamp switch
The exterior lamp switch is located on the
dashboard to the left of the steering wheel.
iIf you drive in countries where vehicles drive
on the other side of the road than the country in
which the vehicle is registered, you must have
the headlamps modified for symmetrical low
beams. Relevant information can be obtained at
your authorized Mercedes-Benz Center.
iThe active Bi-Xenon headlamps monitor
your steering angle and driving speed, then auto-
matically shift their beams to either side to bet-
ter follow the curvature of the road ahead,
increasing usable illumination over conventional
headlamps.
1‚Standing lamps, left (turn left two
stops)
2ˆStanding lamps, right (turn left
one stop)
3MOff
Daytime running lamp mode
(
page 365)
4*Automatic headlamp mode
Daytime running lamp mode
(
page 365)
5CParking lamps (also side marker
lamps, tail lamps, license plate
lamps, instrument panel lamps)
6BLow beam headlamps or high
beam headlamps when the com-
bination switch is pushed for-
ward. The tail lamps, license
plate lamps, side marker lamps,
parking lamps and instrument
panel lamps also come on.
7‡Front fog lamps
8†Rear fog lamp
iIf you hear a warning signal you have forgot-
ten to switch off the headlamps before opening
the driver’s door.
In addition the message “Please switch off
lights” appears in the multifunction display.
Switch off the headlamps.
!Failure to switch off the headlamps when
leaving the vehicle may result in a discharged
battery.
ProCarManuals.com
Page 365 of 723
364 Controls in detail
Lighting
Manual headlamp mode
The low beam headlamps and parking
lamps can be switched on and off with the
exterior lamp switch.
Switching on low beam headlamps
Turn the exterior lamp switch toB.
The green indicator lampC in the
exterior lamp switch comes on.
Automatic headlamp mode
The following lamps switch on and off au-
tomatically depending on the brightness of
the ambient light:
Low beam headlamps
Tail and parking lamps
License plate lamps
Side marker lamps
Turn the exterior lamp switch to *.
With the SmartKey in starter switch po-
sition 1 or the KEYLESS-GO*
start/stop button pressed once, only
the parking lamps and the side marker
lamps will switch on and off automati-
cally.
When the engine is running, the low
beam headlamps, the tail and parking
lamps, the license plate lamps, and the
side marker lamps will switch on and
off automatically.
Warning!G
If the exterior lamp switch is set to*,
the headlamps may switch off unexpect-
edly when the system senses bright am-
bient light, for example light from
oncoming traffic.
the headlamps will not be automatically
switched on under foggy conditions.
To minimize risk to you and to others, acti-
vate headlamps by turning exterior lamp
switch to B when driving or when traffic
and/or ambient lighting conditions require
you to do so.
In low ambient lighting conditions, only
switch from position * to B with the
vehicle at a standstill in a safe location.
Switching from * to B will briefly
switch off the headlamps. Doing so while
driving in low ambient lighting conditions
may result in an accident.
The automatic headlamp feature is only an
aid to the driver. The driver is responsible for
the operation of the vehicle’s lights at all
times.
iUSA only:
With the automatic headlamp mode activated
you can switch on the high beam headlamps in
low ambient lighting conditions.
ProCarManuals.com
Page 367 of 723
366 Controls in detail
Lighting
Locator lighting and night security illu-
mination
The locator lighting and night security illu-
mination are described in the COMAND ve-
hicle section under “Setting locator
lighting” (
page 236) and “Setting night
security illumination” (
page 235).
Fog lampsFront fog lampsSwitch on the low beam
headlampsB (
page 364).
Pull out exterior lamp switch to first
stop.
The front fog lamps are switched on.
The green indicator lamp‡ in the
exterior lamp switch comes on
(
page 363).
Push in the exterior lamp switch.
The front fog lamps are switched off.
The green indicator lamp‡ in the
exterior lamp switch goes out.Rear fog lamp (driver’s side only)
Switch on the low beam
headlampsB (
page 364).
Pull out exterior lamp switch to second
stop.
The front fog lamps and the rear fog
lamp switch on.
The yellow indicator lamp† in the
exterior lamp switch comes on
(
page 363).
Push in the exterior lamp switch to first
stop.
The rear fog lamp switches off.
The green indicator lamp‡ in the
exterior lamp switch goes out.
The front fog lamps remain lit.
Warning!G
In low ambient lighting or foggy conditions,
only switch from position * to B with
the vehicle at a standstill in a safe location.
Switching from * to B will briefly
switch off the headlamps. Doing so while
driving in low ambient lighting conditions
may result in an accident.
iFog lamps will operate with the parking
lamps and/or the low beam headlamps on. Fog
lamps should only be used in conjunction with
low beam headlamps. Consult your State or
Province Motor Vehicle Regulations regarding
permissible lamp operation.
iFog lamps cannot be switched on manually
with exterior lamp switch in position*. To
activate the fog lamps, turn exterior lamp switch
to positionB first.
ProCarManuals.com
Page 370 of 723
369 Controls in detail
Lighting
Hazard warning flasher
The hazard warning flasher can be
switched on at all times, even with the
SmartKey removed from the starter switch
or with the SmartKey with KEYLESS-GO*
removed from the vehicle.
The hazard warning flasher is automatical-
ly switched on if
an air bag has been triggered
CL 600 and USA only: you brake the ve-
hicle strongly at a speed of more than
50 mph (70 km/h) and bring it to a
complete stop
1Hazard warning flasher switch
Switching on: Press hazard warning
flasher switch.
All turn signals will flash.
Switching off: Press hazard warning
flasher switch again.
Interior lighting
iWith the hazard warning flasher activated
and the combination switch set for either left or
right turn, only the respective left or right turn
signals will operate when the SmartKey in the
starter switch is in position1 or2 or the
KEYLESS-GO* start/stop button (
page 337) is
pressed once or twice.
iIf the hazard warning flasher was activated
automatically, also press hazard warning flasher
switch 1 to switch off the hazard warning flash-
er.
iEven with the SmartKey being removed from
the starter switch you can still use the lighting for
the storage compartment, glove box and vanity
mirrors, when you open a door or press one of
the interior lighting buttons. If a lamp is switched
on it will be switched off automatically after 30
minutes.
When you lock the vehicle from the outside, the
interior lighting is switched off.
ProCarManuals.com
Page 375 of 723
374 Controls in detail
Power windows
Opening and closing power windows
The side windows are opened and closed
electrically. The switches
for all side windows are on the driver’s
door
for the passenger door window are on
the passenger door
for each rear side window are on the re-
spective rear side trim panel
1Left front window
2Right front window
3Left rear window
4Right rear window
Warning!G
When closing the windows, make sure there
is no danger of anyone being harmed by the
closing procedure.
Activate the override switch (
page 62)
when children are riding in the back seats of
the vehicle. The children may otherwise in-
jure themselves, e.g. by becoming trapped
in the window opening.
The closing of the side windows can be im-
mediately halted by releasing the switch or,
if the switch was pressed past the resis-
tance point and released, by pressing the
lower part of the respective switch again.
The door windows are equipped with the ex-
press-close and automatic reversal func-
tion. If a door window encounters an
obstruction that blocks its path in a circum-
stance where you pressed the switch past
the resistance point and released it to close
the window, the automatic reversal function
will stop the window and open it slightly.
If a door window encounters an obstruction
that blocks its path in a circumstance where
you are closing the window by pressing and
holding the switch, by pressing and holding
button ‹ on the SmartKey or SmartKey
with KEYLESS-GO*, by pressing and holding
the sensor surface (vehicles with
KEYLESS-GO*) on an outside door handle,
or by pressing and holding button, on
the climate control panel, the automatic re-
versal function will not operate.
When leaving the vehicle, always remove the
SmartKey or SmartKey with KEYLESS-GO*
from the starter switch, take it with you, and
lock the vehicle. Do not leave children unat-
tended in the vehicle, or with access to an
unlocked vehicle. A child’s unsupervised ac-
cess to a vehicle could result in an accident
and/or serious personal injury.
ProCarManuals.com
Page 376 of 723
375 Controls in detail
Power windows
Switch on the ignition (page 336).
Opening: Press the lower part of
switch1 to 4 (
page 374) to the re-
sistance point.
The corresponding window will move
downwards until you release the
switch.
Closing: Press the upper part of
switch1 to 4 (
page 374) to the re-
sistance point.
The corresponding window will move
upwards until you release the switch.
Express-opening: Press the lower part
of switch1 to4 (
page 374) past
the resistance point and release.
The corresponding window opens com-
pletely.
Express-closing (door windows
only): Press the upper part of
switch1 to4 (
page 374) past the
resistance point and release.
The corresponding window closes com-
pletely.
iYou can also open or close the windows us-
ing the SmartKey, see “Summer opening fea-
ture” (
page 376) and “Convenience closing
feature” (
page 376).
Depending on current position, the windows may
also open or close when the air recirculation
button, (
page 453) is pressed and held
for 2 seconds
iOperating the windows from the rear is not
possible if you activate the override switch
(
page 62).
iIf PRE-SAFE® has been activated, the front
side windows close automatically until only a
small gap remains.
iWith the SmartKey in starter switch
position0 or removed from the starter switch,
the power windows can be operated:
until you open the driver’s or passenger’s
door
for at least 5 minutes if no door was opened
Warning!G
If you press and hold the switch up when
closing the window, and upward movement
of the window is blocked by some obstruc-
tion including but not limited to arms, hands,
fingers, etc., the automatic reversal will not
operate.
Warning!G
Driver’s door only:
If within 5 seconds you again press the
switch past the resistance point and re-
lease, the automatic reversal will not
operate.
ProCarManuals.com
Page 377 of 723
376 Controls in detail
Power windows
Stopping during Express-operation:
Briefly press the respective power win-
dow switch again.
Summer opening feature
If the weather is warm, you can ventilate
the vehicle before driving off by simulta-
neously:
opening the side windows
opening the tilt/sliding sunroof
turning on the seat ventilation* for the
driver’s seat
Aim transmitter eye of the SmartKey or
SmartKey with KEYLESS-GO* at the
driver’s outside door handle. The
SmartKey or SmartKey with
KEYLESS-GO* must be in close proxim-
ity to the driver’s door handle.
Press and hold button Πuntil the
side windows and tilt/sliding sunroof
have reached the desired position.The vehicle unlocks.
Release button Πto interrupt pro-
cedure.
Convenience closing feature
When you lock the vehicle, you can close
the side windows and tilt/sliding sunroof
simultaneously.
!If the upward movement of a door window is
blocked during the closing procedure, the door
window will stop and open slightly.
Remove the obstruction, press the respective
power window switch at the upper part again
past the resistance point and release.
If the door window still does not close when
there is no obstruction, press and hold the re-
spective power window switch at the upper part.
The door window will then close without the ob-
struction sensor function.iThe “Summer opening” function can only be
activated via the remote control of the SmartKey
or SmartKey with KEYLESS-GO*.
iThe seat ventilation* for the driver’s seat is
automatically set to the highest level if activated
via summer opening feature.
iThe function of the SmartKey overrules the
KEYLESS-GO* function.
Warning!G
When closing the side windows and the
tilt/sliding sunroof, make sure that there is
no danger of anyone being harmed by the
closing procedure.
If potential danger exists, proceed as fol-
lows:
Release button ‹ to stop the closing
procedure. To open, press and hold but-
ton Œ. To continue the closing after
making sure that there is no danger of
ProCarManuals.com
Page 379 of 723
378 Controls in detail
Driving and parking
Starting the engine Automatic transmission
Gearshift pattern for automatic
transmission
PPark position
RReverse gear
NNeutral
DDrive position
For more information on how to operate
the gear selector lever, see “Automatic
transmission” (
page 389).
Warning!G
Make sure that absolutely no objects are ob-
structing the pedals’ range of movement.
Keep the driver’s footwell clear of all obsta-
cles. If there are any floormats or carpets in
the footwell, make sure that the pedals still
have sufficient clearance.
During sudden driving or braking maneuvers
the objects could get caught between the
pedals. You could then no longer brake or
accelerate. This could lead to accidents and
injury.Warning!G
Inhalation of exhaust gas is hazardous to
your health. All exhaust gas contains carbon
monoxide (CO), and inhaling it can cause un-
consciousness and possible death.
Do not run the engine in confined areas
(such as a garage) which are not properly
ventilated. If you think that exhaust gas
fumes are entering the vehicle while driving,
have the cause determined and corrected
immediately. If you must drive under these
conditions, drive with at least one window
fully open.
ProCarManuals.com