belt MERCEDES-BENZ CLA 2014 Owner's Guide

Adjusting the seats electrically
Head restraintheight2
Seat cushion angle
"Seat height
!Seat fore-and-aft adjustment
Backrest angle
iYou can store the seat settings using the
memory function (Ypage 100).
Adjusting the head restraints
GWARNING
You could lose control of your vehicle if you
do the following while driving:
Radjust the driver's seat, head restraint,
steering wheel or mirrors
Rfasten the seat belt
There is a risk of an accident.
Adjust the driver's seat, head restraint,
steering wheel and mirror and fasten your
seat belt before starting the engine.
GWARNING
If head restraints are not installed and
adjusted correctly, they cannot provide
protection as intended. There is an increased
risk of injury in the head and neck area, e.g.
in the event of an accident or when braking.
Always drive with the head restraints
installed. Before driving off, make sure for
every vehicle occupant that the center of the
head restraint supports the back of the head
at about eye level.
General notes
For vehicles with sports seats, you cannot
adjust the head restraints or remove and
install the rear head restraints.
Adjusting the head restraints manually
Adjusting the head restraint height
XTo raise:pull the head restraint up to the
desired position.
XTo lower:press release catchin the
direction of the arrow and push the head
restraint down to the desired position.
Adjusting the fore/aft position of the
head restraint
2Not available on vehicles with sports seats.
Seats93
Seats, steering wheel and mirrors
Z

Problems with the seat heating
ProblemPossible causes/consequences and
Solutions
The seat heating has
switched off
prematurely or cannot
be switched on.
The on-board voltage is too low because too many electrical
consumers are switched on.
XSwitch off electrical consumers that you do not need, such as
the rear window defroster or interior lighting.
Once the battery is sufficiently charged, the seat heating will
switch back on automatically.
AMG Performance Seat
To adjust the contour of the seat and for
improved lateral support, you can individually
adjust the front seats.
Adjusting the seat cushion length
XTo extend the seat cushion:press
button.
XTo retract the seat cushion:press
button.
Adjusting the side bolsters of the seat
cushion
XTo set the side bolsters of the seat
cushion narrower:press button".
XTo set the side bolsters of the seat
cushion wider:press button!.
Adjusting the seat backrest side
bolsters
XTo set the side bolsters of the seat
cushion narrower:press button.
XTo set the side bolsters of the seat
cushion wider:press button .
Steering wheel
Important safety notes
GWARNING
You could lose control of your vehicle if you
do the following while driving:
Radjust the driver's seat, head restraint,
steering wheel or mirrors
Rfasten the seat belt
There is a risk of an accident.
Adjust the driver's seat, head restraint,
steering wheel and mirror and fasten your
seat belt before starting the engine.
GWARNING
Children could injure themselves if they
adjust the steering wheel. There is a risk of
injury.
When leaving the vehicle, always take the
SmartKey with you and lock the vehicle. Never
leave children unsupervised in the vehicle.
96Steering wheel
Seats, steering wheel and mirrors

Rthe electric parking brake is applied.
RESP®is malfunctioning.
Furtherinformation on holding the vehicle
stationary on uphill gradients (Ypage 145).
ECO start/stopfunction
Introduction
The ECO start/stop function switches the
engine off automatically if the vehicle is
stopped undercertain conditions.
The engine starts automatically when the
driver wants to pull away again. The ECO
start/stop function thereby helps you to
reduce the fuel consumption and emissions
of your vehicle.
Important safety notes
GWARNING
If the engine is switchedoff automatically and
you exit the vehicle, the engine is restarted
automatically.The vehicle may begin moving.
There is a risk of accident and injury.
If you wish to exit the vehicle, always turn off
the ignition and secure the vehicle against
rolling away.
General notes
ECO start/stop display
If the\rsymbol is shown in green in the
multifunction display, the ECO start/stop
function switches the engine off
automatically if the vehicle stops moving.
The stop/start function is automatically
activated each time you start the engine with
the SmartKey.
If the ECO start/stop function has been
manually deactivated (Ypage 140) or a
malfunction has caused the system to be
deactivated, the\rsymbol is not
displayed.
AMG vehicles:the ECO start/stop function
is only available in drive programC.
Automatic engine switch-off
General notes
The ECO start/stop function is operational
and the\rsymbol is displayed in green in
the multifunction display, if:
Rthe indicator lamp in the ECO button is lit
green.
Rthe outside temperature is within the range
that is suitable for the system.
Rthe engine is at normal operating
temperature.
Rthe set temperature for the vehicle interior
has been reached.
Rthe battery is sufficiently charged.
Rthe system detects that the windshield is
not fogged up when the air-conditioning
system is switched on.
Rthe hood is closed.
Rthe driver's door is closed and the driver's
seat belt is fastened.
If not all conditions for automatic engine
switch-off are fulfilled, the\rsymbol is
shown in yellow.
iAll of the vehicle's systems remain active
when the engine has been stopped
automatically.
iThe engine can be switched off
automatically a maximum of four times
(first stop and three subsequent stops) in
succession. The\rsymbol is shown in
yellow in the multifunction display after the
engine has been started automatically for
the fourth time. When the\rsymbol is
shown in green in the multifunction display,
Driving139
Driving and parking
Z

automatic engine switch-off is again
possible.
Vehicles with automatic transmission
If the vehicle is braked to a standstill inDor
N, the ECO start/stop function switches off
the engine automatically.
iThe HOLD function can be activated if the
engine has been switched off
automatically. It is then not necessary to
continue applying the brakes during the
automatic stop phase.When you depress
the accelerator pedal, the engine starts
automatically and the braking effect of the
HOLD function is deactivated.
Automatic engine start
General notes
The engine starts automatically if:
Ryou switch off the ECO start/stop function
by pressing the ECO button.
Ryou engage reverse gearR.
Rthe vehicle starts to roll.
Rthe brake system requires this.
Rthe temperature in the vehicle interior
deviates from the set range.
Rthe system detects moisture on the
windshield when the air-conditioning
system is switched on.
Rthe condition of charge of the battery is too
low.
Rthe driver's seat belt is removed or the
driver's door is opened.
Vehicles with automatic transmission
The engine is started automatically if you:
Rrelease the brake pedal when HOLD is not
activated and the transmission is in
positionDorN.
Rdepress the accelerator pedal.
Rmove the transmission out of positionP.
iShifting the transmission to positionP
does not start the engine.
iIf you shift the transmission fromRtoD,
the ECO start/stop function is available
again once the\rsymbol reappears in
green in the multifunction display.
Deactivating/activating the ECO start/
stop function
ECO button
XTo switch off:press button.
Indicator lampand the\rsymbol in
the multifunction display go out.
XTo switch on:press button.
Indicator lamplights up.
If all conditions for automatic engine
switch-off (Ypage 139) are fulfilled, the
\rsymbol is shown in green in the
multifunction display.
If not all conditions for automatic engine
switch-off (Ypage 139) are fulfilled, the
\rsymbol is shown in yellow in the
multifunction display. If this is the case, the
ECO start/stop function is not available.
iIf indicator lampis off, the ECO start/
stop function has been deactivated
manually or as the result of a malfunction.
The engine will then not be switched off
automatically when the vehicle stops.
140Driving
Driving and parking

In addition, they may operate vehicle
equipment and become trapped.There is a
risk of an accident and injury.
When leaving the vehicle, always take the
SmartKey with you and lock the vehicle. Never
leave children unsupervised in the vehicle.
iThe electric parking brake performs a
function test at regular intervals while the
engine is switched off. The sounds that can
be heard while this is occurring are normal.
Applying/releasing manually
Applying
XPush handle.
When the electric parking brake is applied,
the(USA only) or (Canada only)
red indicator lamp lights up in the
instrument cluster.
iThe electric parking brake can also be
applied when the SmartKey is removed.
Releasing
XPull handle.
The red(USA only) or (Canada
only) indicator lamp in the instrument
cluster goes out.
iYou can only release the electric parking
brake when the SmartKey is in position1
or2in the ignition lock.
Applying automatically
The electric parking brake is applied
automatically:
Rif DISTRONIC PLUS brings the vehicle to a
standstill or
Rif the HOLD function is keeping the vehicle
stationary or
Rif Active Parking Assist is holding the
vehicle at a standstill
In addition, at least one of the following
conditions must be fulfilled:
Rthe engine is switched off.
Rthe driver's door is open and the seat belt
is not fastened.
Rthere is a system malfunction.
Rthe power supply is insufficient.
Rthe vehicle is stationary for a lengthy
period.
The red(USA only) or (Canada
only) indicator lamp in the instrumentcluster
lights up.
iThe electric parking brake is not
automatically engaged if the engine is
switched off by the ECO start/stop
function.
Releasing automatically
Your vehicle's electric parking brake is
automatically released if all of the following
conditions are met:
Rthe engine is running.
Rthe transmission is in positionDorR.
Rthe seat belt has been fastened.
Ryou depress the accelerator pedal.
If the transmission is in positionR, the tailgate
must be closed.
Parking155
Driving and parking
Z

If yourseat belt is not fastened, the following
conditions must be fulfilled to automatically
release the electric parkingbrake:
Rthe driver's door is closed.
Ryou have shifted out of transmission
positionPor you have previously driven
faster than 2 mph (3 km/h).
Emergency braking
The vehicle can also be braked during an
emergency by using the electric parking
brake.
XWhile driving, push handleof the electric
parking brake (Ypage 154).
iThe vehicle is braked for as long as
handleof the electric parking brake is
pressed. The longer electric parking brake
handleis depressed, the greater the
braking force.
During braking:
Ra warning tone sounds
RtheRelease Park. Brakemessage
appears
Rthe red(USA only) or (Canada
only) indicator lamp in the instrument
cluster flashes
When the vehicle has been braked to a
standstill, the electric parking brake is
engaged.
Parking the vehicle foralong period
If you leave the vehicle parked for longer than
four weeks, the battery may be damaged by
exhaustive discharging.
If you leave the vehicle parked for longer than
six weeks, the vehicle may suffer damage as
a result of lack of use.
XVisit a qualified specialist workshop and
seek advice.
iYou can obtain information about trickle
chargers from a qualified specialist
workshop.
Driving tips
General notes
Important safety notes
GWARNING
If you switch off the ignitionwhile driving,
safety-relevant functions are only available
with limitations, or not at all. This could affect,
for example, the power steering and the brake
boosting effect.You will require considerably
more effort to steer and brake. There is a risk
of an accident.
Do not switch off the ignition while driving.
GWARNING
If you operate mobile communication
equipment while driving, you will be
distracted from traffic conditions. You could
also lose control of the vehicle. There is a risk
of an accident.
Only operate this equipment when the vehicle
is stationary.
Observe the legal requirements for the
country in which you are driving. Some
jurisdictions prohibit the driver from using a
mobile phone while driving a vehicle.
If you make a call while driving, always use
hands-free mode. Only operate the telephone
when the traffic situation permits. If you are
unsure, pull over to a safe location and stop
before operating the telephone.
Bear in mind that at a speed of only 30 mph
(approximately 50 km/h), the vehicle covers
a distance of 44 ft (approximately 14 m) per
second.
156Driving tips
Driving and parking

Cruise control lever
To store the currentspeed or a higher
speed
To store the currentspeed or a lower
speed
"To deactivate DISTRONIC PLUS
!To store the currentspeed or calling up
the last stored speed
To set the specified minimum distance
Activating DISTRONIC PLUS
Activation conditions
To activate DISTRONIC PLUS, all of the
following activation conditions must be
fulfilled:
Rthe engine must be started. It may take up
to two minutes after pulling away before
DISTRONIC PLUS is operational.
Rthe electric parking brake must be
released.
RESP®must be active, but not intervening.
RActive Parking Assist must not be
activated.
Rthe transmission must be in positionD.
Rthe driver's door must be closed when you
shift fromPtoDor your seat belt must be
fastened.
Rthe front-passenger door and rear doors
must be closed.
Activating
XBriefly pull the cruise control lever towards
you!or press it upor down.
DISTRONIC PLUS is selected.
XPress the cruise control lever repeatedly
upor downuntil the desired speed
is set.
XRemove your foot from the accelerator
pedal.
Your vehicle adapts its speed to that of the
vehicle in front, but only up to the desired
stored speed.
iIf you do not fully release the accelerator
pedal, theDISTRONIC PLUS Passive
message appears in the multifunction
display. The set distance to a slower-
moving vehicle in front will then not be
maintained. You will be driving at the speed
you determine by the position of the
accelerator pedal.
You can also activate DISTRONIC PLUS when
stationary. The lowest speed that can be set
is 18 mph (30 km/h).
XBriefly pull the cruise control lever towards
you!or press it upor down.
DISTRONIC PLUS is selected.
Activating at the current speed/last
stored speed
GWARNING
If you call up the stored speed and it differs
from the current speed, the vehicle
accelerates or decelerates. If you do not know
the stored speed, the vehicle could accelerate
or brake unexpectedly. There is a risk of an
accident.
Pay attention to the road and traffic
conditions before calling up the stored speed.
If you do not know the stored speed, store the
desired speed again.
166Driving systems
Driving and parking

Rthe battery is disconnected.
Rthe accelerator pedal has been depressed,
e.g.by a vehicle occupant.
There is a risk of an accident.
If you wish to exit the vehicle, always turnoff
DISTRONIC PLUS and secure the vehicle
against rolling away.
For further information on deactivating
DISTRONIC PLUS (Ypage 169).
If DISTRONIC PLUS detects that the vehicle
in front is stopping, it brakes yourvehicle until
it is stationary.
Once your vehicle is stationary, it remains
stationary and you do not need to depress the
brake.
iAfter a time, the electric parking brake
secures the vehicle and relieves the service
brake.
iDepending on the specified minimum
distance, your vehicle will come to a
standstill at a sufficientdistance behind the
vehicle in front.The specified minimum
distance is set using the control on the
cruise control lever.
The electric parking brake automatically
secures the vehicle if DISTRONIC PLUS is
activated and:
Rthe seat belt is unfastened and the driver's
door is open.
Rthe engine is switched off, unless it is
automatically switched off by the ECO
start/stop function.
Ra system malfunction occurs.
Rthe power supply is not sufficient.
If a malfunction occurs, then the transmission
may be shifted into positionPautomatically.
Settingaspeed
Keep in mind thatitmay take a briefmoment
until the vehicle has accelerated or braked to
the speed set.
To store the current speed or a higher
speed
To store the current speed or a lower
speed
XPress the cruise control lever upfor a
higher speed or downfor a lower speed.
XTo adjust the set speed in 1 mph
increments (1 km/h increments):briefly
press the cruise control lever upor
downto the pressure point.
Every time the cruise control lever is
pressed upor downthe last speed
stored is increased or reduced.
XTo adjust the set speed in 5 mph
increments (10 km/h increments):
briefly press the cruise control lever
upor downto the pressure point.
Every time the cruise control lever is
pressed upor down, the last speed
stored is increased or reduced.
iDISTRONIC PLUS is not deactivated if you
depress the accelerator pedal. If you
accelerate to overtake, DISTRONIC PLUS
adjusts the vehicle's speed to the last
speed stored after you have finished
overtaking.
Setting the specified minimum distance
You can set the specified minimum distance
for DISTRONIC PLUS by varying the time span
between one and two seconds. With this
function, you can set the minimum distance
that DISTRONIC PLUS keeps to the vehicle in
front, dependent on vehicle speed. You can
168Driving systems
Driving and parking

Crossing vehicles
DISTRONIC PLUS may detect vehicles that
are crossing your lane by mistake. Activating
DISTRONIC PLUS at traffic lights with
crossing traffic, for example, could cause
your vehicle to pull away unintentionally.
HOLD function
Important safety notes
GWARNING
When leaving the vehicle, it can still roll away
despite being braked by theHOLD function if:
Rthere is a malfunction in the system or in
the voltage supply.
Rthe HOLD function has been deactivated by
pressing the accelerator pedal or the brake
pedal, e.g. by a vehicle occupant.
Rthe electrical system in the engine
compartment, the battery or the fuses have
been tampered with.
Rthe battery is disconnected
There is a risk of an accident.
If you wish to exit the vehicle, always turn off
the HOLD function and secure the vehicle
against rolling away.
!If DISTRONIC PLUS or the HOLD function
is activated, the vehicle brakes
automatically in certain situations. To
prevent damage to the vehicle, deactivate
DISTRONIC PLUS and the HOLD function in
the following or other similarsituations:
Rwhen towing the vehicle
Rin the car wash
Deactivating the HOLD function
(Ypage 173).
General notes
The HOLDfunction can assistthe driver in the
following situations:
Rwhen pulling away, especially on steep
slopes
Rwhen maneuvering on steep slopes
Rwhen waiting in traffic
The vehicle is kept stationary without the
driver having to depress the brake pedal.
The braking effect is canceled and the HOLD
function deactivated when you depress the
accelerator pedal to pull away.
Activation conditions
You can activate the HOLD function if:
Rthe vehicle is stationary
Rthe engine is running or if it has been
automatically switched off by the ECO
start/stop function
Rthe driver's door is closed or your seat belt
is fastened
Rthe electric parking brake is released
Rthe transmission positionD,RorNis
engaged while driving a vehicle with an
automatic transmission
RDISTRONIC PLUS is deactivated
172Driving systems
Driving and parking

Activating the HOLD function
Example: vehicles with a color multifunctiondisplay
XMake sure that the activation conditions
are met.
XDepress the brake pedal.
XQuickly depress the brake pedal further
untilappears in the multifunction
display.
The HOLD function is activated. You can
release the brake pedal.
iIf depressing the brake pedal the first
time does not activate the HOLD function,
wait briefly and then try again.
Deactivating the HOLD function
The HOLD function is deactivated
automatically if:
Ryou accelerate.Onvehicles with automatic
transmission:only when the transmission
is in positionDorR.
Rthe transmission is in positionPon vehicles
with automatic transmission.
Ryou depress the brake pedal againwith a
certain amountofpressure until
disappears from the multifunction display.
Ryou secure the vehicle using the electric
parking brake.
Ryou activate DISTRONIC PLUS.
iAfter a time, the electric parking brake
secures the vehicle and relieves the service
brake.
The electric parking brake automatically
secures the vehicle if the HOLD function is
activated and:
Rthe driver's door is open and the driver's
seat beltis unfastened.
Rthe engine is switched off, unless it is
automatically switched off by the ECO
start/stop function.
Ra system malfunction occurs.
Rthe power supply is not sufficient.
If a malfunction occurs, then the transmission
may be shifted into positionPautomatically.
RACE START
Important safety notes
RACE START enables optimal acceleration
from a standing start. The precondition for
this is a suitable high-grip road surface.
RACE START is intended solely for activation
on dedicated race circuits.
iRACE START is only available in AMG
vehicles.
Conditions for activation
You can activate RACE START if:
Rthe doors, hood and the trunk lid are
closed.
Rthe engine is running and the transmission,
all-wheel drive clutch and the engine are at
operating temperature.
RSPORT handling mode is activated.
(Ypage 66)
Rthe steering wheel is in the straight-ahead
position.
Rthe vehicle is stationary and the brake
pedal is depressed (left foot).
Rthe transmission is in positionD.
Rdrive programMis selected (Ypage 146).
Driving systems173
Driving and parking
Z