sensor MERCEDES-BENZ CLA 2014 Owner's Guide

Display messagesPossible causes/consequences and
Solutions

Check Rear Left
Sidemarker Lampor
Check Rear Right
Sidemarker Lamp
The rear leftorright side marker lamp is defective.
XCheck whether you are permitted to replace the bulb yourself
(Ypage 111).
or
XVisit a qualified specialist workshop.

CheckLeftDaytime
Running Lightor
Check Right
Daytime Running
Light
The left-hand or right-hand daytime running lamp is faulty.
XCheck whether you are permitted to replace the bulb yourself
(Ypage 111).
or
XVisit a qualified specialist workshop.

Active Light
System Inoperative
The active light function is defective.
XVisit a qualified specialist workshop.

Malfunction See
Operator's Manual
The exterior lighting is defective.
XVisit a qualified specialist workshop.

AutoLampFunction
Inoperative
The light sensor is defective.
XVisit a qualified specialist workshop.

Switch Off Lights
The lights are still switched on when you leave the vehicle. A
warning tone also sounds.
XTurn the light switch to.
Adaptive Highbeam
Assist Inoperative
Adaptive Highbeam Assist is faulty.
XVisit a qualified specialist workshop.
Adaptive Highbeam
Assist Currently
Unavailable See
Operator's Manual
Adaptive Highbeam Assist is deactivated and temporarily
inoperative. Possible causes are:
Rthe windshield in the camera's field of vision is dirty.
Rvisibility is impaired due to heavy rain, snow or fog.
XClean the windshield.
If the system detects that the camera is fully operational again,
theAdaptive Highbeam Assist Now Availablemessage is
displayed.
Adaptive Highbeam Assist is operational again.
226Display messages
On-board computer and displays

Display messagesPossible causes/consequences and
Solutions
SpeedLimitAssist
Inoperative
Speed Limit Assistis faulty.
XVisit a qualified specialist workshop.

Off
The HOLD function is deactivated. The vehicle is skidding.
Awarning tone also sounds.
XReactivate the HOLD function later (Ypage 172).
The HOLD function is deactivated. When the brakepedal is firmly
depressed, an activation condition is not fulfilled.
Awarning tone also sounds.
XCheck the activation conditions for the HOLD function
(Ypage 172).
Radar Sensors
Deactivated See
Operator's Manual
The radar sensor system is deactivated.
XSwitch on the radar sensor system (Ypage 208).
Lane Keeping
Assist Currently
Unavailable See
Operator's Manual
Lane Keeping Assist is deactivated and temporarily inoperative.
Possible causes are:
Rthe windshield in the camera's field of vision is dirty.
Rvisibility is impaired due to heavy rain, snow or fog.
Rthere are no lane markings for a longer period.
Rthe lane markings are worn, dark or covered, e.g.by dirtorsnow.
Whenthe causes stated above no longer apply, the display
message disappears.
Lane Keeping Assist is operational again.
If the display message does not disappear:
XPull over and stop the vehicle safely as soon as possible, paying
attention to road and traffic conditions.
XSecure the vehicle against rolling away (Ypage 153).
XCleanthe windshield.
Lane Keeping
Assist Inoperative
Lane Keeping Assist is faulty.
XVisit a qualified specialist workshop.
230Display messages
On-board computer and displays

Display messagesPossible causes/consequences and
Solutions
Blind Spot Assist
Currently
Unavailable See
Operator's Manual
Blind Spot Assistis temporarily inoperative. Possible causes are:
Rthe sensors are dirty.
Rfunction is impaired due to heavy rain or snow.
Rthe radar sensor system is outside the operating temperature
range.
Rthe radar sensor system is temporarily inoperative, e.g. due to
electromagnetic radiation emitted by nearby TV or radio
stations or other sources of electromagnetic radiation.
The yellowindicator lamps also light up in the exterior
mirrors.
When the causes stated above no longer apply, the display
message disappears.
Blind Spot Assist is operational again.
If the display message does not disappear:
XPull over and stop the vehicle safely as soon as possible, paying
attention to road and traffic conditions.
XSecure the vehicle against rolling away (Ypage 153).
XCleanthe sensors (Ypage 289).
XRestart the engine.
Blind Spot Assist
Inoperative
Blind Spot Assist is defective.
The yellowindicator lamps also light up in the exterior
mirrors.
XVisit a qualified specialist workshop.
Park Assist
Canceled
The driver's door is open and the driver's seat belt has not been
fastened.
XRepeatthe parking process with the seat belt fastened and the
driver's door closed.
You have inadvertently touched the multifunction steering wheel
while steering intervention was active.
XWhile steering intervention is active, make sure that the
multifunction steering wheel is not touched unintentionally.
The vehicle has started to skid and ESP®has intervened.
XUse Active Parking Assist again later (Ypage 178).
Display messages231
On-board computer and displays
Z

Display messagesPossible causes/consequences and
Solutions
Park Assist
Inoperative
You have just carried out a large number of turning or parking
maneuvers.
Active Parking Assistwill become available again after
approximately ten minutes (Ypage 178).
XPull over and stop the vehicle safely as soon as possible, paying
attention to road and traffic conditions.
XSwitch off and restart the engine.
If the display message continues to be displayed:
XVisit a qualified specialist workshop.
PARKTRONIC is defective.
XVisit a qualified specialist workshop.
DISTRONIC PLUS OffDISTRONIC PLUS has been deactivated (Ypage 164). If it was
deactivated automatically, a warning tone also sounds.
DISTRONICPLUSNow
Available
DISTRONIC PLUS is operational again after having been
temporarily unavailable. You can now reactivate DISTRONIC PLUS
(Ypage 164).
DISTRONIC PLUS
Currently
Unavailable See
Operator's Manual
DISTRONIC PLUS is temporarily inoperative. Possible causes are:
Rfunction is impaired due to heavy rain or snow.
Rthe sensors in the radiator trim are dirty
Rthe radar sensor system is temporarily inoperative, e.g. due to
electromagnetic radiation emitted by nearby TV or radio
stations or other sources of electromagnetic radiation.
Rthe system is outside the operating temperature range.
Rthe on-board voltage is too low.
Awarning tone also sounds.
When the causes stated above no longer apply, the display
message disappears.
DISTRONIC is operational again.
If the display message does notdisappear:
XPull over and stop the vehicle safely as soon as possible, paying
attention to road and traffic conditions.
XSecure the vehicle against rolling away (Ypage 153).
XClean the sensors in the radiator trim (Ypage 289).
XRestartthe engine.
232Display messages
On-board computer and displays

Display messagesPossible causes/consequences and
Solutions
Tire Press.
Monitor Currently
Unavailable
Due to a source of radiointerference, no signals can be received
from the wheel sensors.The tire pressure monitor is temporarily
malfunctioning.
XDrive on.
The tire pressure monitor restarts automatically as soon as the
problem has been solved.
TirePress.
Sensor(s) Missing
There is no signal from the tire pressure sensor of one or several
wheels. The pressure of the affected tire is not displayed in the
multifunction display.
XHave the faulty tire pressure sensor replaced at a qualified
specialist workshop.
Tire Pressure
Monitor
Inoperative No
Wheel Sensors
The wheels mounted do not have a suitable tire pressure sensor.
The tire pressure monitor is deactivated.
XMount wheels with suitable tire pressure sensors.
The tire pressure monitor is activated automatically after driving
for a few minutes.
Tire Press.
Monitor
Inoperative
The tire pressure monitor is faulty.
XVisit a qualified specialist workshop.
Vehicle
Display messagesPossible causes/consequences and
Solutions
Shiftto'P'or'N'
to Start Engine
You have attempted to start the engine with the transmission in
positionRorD.
XShift the transmission to positionPorN.
Auxiliary Battery
Malfunction
The auxiliary battery for the automatic transmission is no longer
being charged.
XVisit a qualified specialist workshop at the next opportunity.
XUntil then, set the automatic transmission to positionPbefore
you switch off the engine.
XBefore leaving the vehicle, apply the electric parking brake.
Depress Brake to
Start Engine
You have attempted to start the engine with the transmission in
positionNwithout depressing the brake pedal.
XDepress the brake pedal.
236Display messages
On-board computer and displays

Engine
ProblemPossible causes/consequences and
Solutions

The yellow Check
Engine warning lamp
lights up while the
engine is running.
There may be a malfunction, for example:
Rin the engine management
Rin the fuel injection system
Rin the exhaust system
Rin the ignition system
Rin the fuel system
The emission limit values may be exceeded and the enginemay
be running in emergency mode.
XHave the vehicle checked as soon as possible at a qualified
specialist workshop.
iIn some states, you must immediately visit a qualified
specialist workshop as soon as the yellow CheckEngine warning
lamp lights up.This depends on the locally applicable legal
requirements. If in doubt, check whether such legal regulations
apply in the state in which you are currently driving.


The yellow reserve fuel
warning lamp lights up
while the engine is
running.
The fuel level has dropped into the reserve range.
XRefuel at the nearest gas station.


The yellow reserve fuel
warning lamp flashes
while the engine is
running.
The fuel system pressure is too low. The fuel filler cap is not closed
correctly or the fuel system is leaking.
XCheck that the fuel filler cap is correctly closed.
XIf the fuel filler cap is not correctly closed:close the fuel filler
cap.
XIf the fuel filler cap is closed:visit a qualified specialist
workshop.
\r
The red coolant
warning lamp lights up
while the engine is
running and the coolant
temperature gage is at
the start of the scale.
The temperature sensor for the coolant temperature gage is
defective.
The coolant temperature is no longer being monitored. There is a
risk of engine damage if the coolant temperature is too high.
XPull over and stop the vehicle safely and switch off the engine,
paying attention to road and traffic conditions. Do not continue
driving under any circumstances.
XSecure the vehicle against rolling away (Ypage 153).
XConsult a qualified specialist workshop.
248Warning and indicator lamps in the instrument cluster
On-board computer and displays

Cleaning the mirror turn signals
!Only use cleaning agents or cleaning
cloths that are suitable for plastic lenses.
Unsuitable cleaning agents or cleaning
cloths could scratch or damage the plastic
lenses of the mirror turnsignals.
XClean the plastic lenses of the mirror turn
signals in the exterior mirror housing using
a wet sponge and a mild cleaning agent,
e.g. Mercedes-Benzcar shampoo or
cleaning cloths.
Cleaning the sensors
!If you clean the sensorswith a power
washer, make sure that you keep a
distance of at least 11.8in(30 cm) between
the vehicle and the power washer nozzle.
Information about the correct distance is
available from the equipment
manufacturer.
XClean sensorsof the driving systems
with water, car shampoo and a soft cloth.
Cleaning the rear view camera
!Do not cleanthe camera lens and the area
around the rear view camera with a power
washer.
XMake sure that the vehicle is stationary and
that the SmartKey is in position2in the
ignition lock.
XTo open the cover of the rear view
camera:with the audio system/COMAND
activated, press thebutton.
XSelectSystemby turning\rthe audio
system/COMAND controller and press\n
to confirm.
XSelectRearviewcameraand press\nto
confirm.
XSelectOpen camera coverand confirm
with\n.
The cover of the 360° camera opens.
XTo clean the rear view camera:use clear
water and a soft cloth to clean camera
lens.
Cleaning the exhaust pipes
Impurities combined with the effects of road
grit and corrosive environmental factors may
cause flash rust to form on the surface. You
can restore the original shine of the exhaust
pipe by cleaning it regularly, especially in
winter and after washing.
!Do not clean the exhaust pipe with acid-
based cleaning agents such as sanitary
cleansers or wheel cleaners.
XCleanthe exhaust pipe with a care product
tested and approved by Mercedes-Benz.
!AMG vehicles with black exhaust pipes:
do not use chrome polish to polish black
chromed screens. They will otherwise lose
Care289
Maintenance and care
Z

XBefore restarting, make sure that the tire
pressures are set properly on all fourtires
for the respective operating conditions.
The recommended tire pressures can be
found on the Tire and Loading Information
placard on the B-pillar on the driver's side
or the tire pressure table on the fuel filler
flap. The tire pressure loss warning system
can only give reliable warnings if you have
set the correct tirepressure. If an incorrect
tire pressure is set, these incorrect values
will be monitored.
XAlso observe the notes in the section on tire
pressures (Ypage 316).
XMake sure that the SmartKey is in position
2in the ignitionlock (Ypage 137).
XPressoron the steering wheel
to select theServicemenu.
XPress theorbutton to select
Tire Pressure.
XPress thebutton.
TheRun Flat Indicator Active
Press 'OK' to Restartmessage
appears in the multifunction display.
If you wish to confirm the restart:
XPress thebutton.
TheTire Pressure Now OK?message
appears in the multifunction display.
XPress theorbutton to select
Yes.
XPress thebutton.
TheRun Flat Indicator Restarted
message appears in the multifunction
display.
After a teach-in period, the tire pressure
loss warning system will monitor the set
tire pressures of all four tires.
If you wish to cancel the restart:
XPress thebutton.
or
XWhen theTire Pressure Now OK?
message appears, press the
orbutton to selectCancel.
XPress thebutton.
The tire pressure values stored at the last
restart will continue to be monitored.
Tire pressure monitor
General notes
If a tire pressure monitor is installed, the
vehicle's wheels have sensors that monitor
the tire pressures in all four tires. The tire
pressure monitor warns you if the pressure
drops in one or more of the tires. The tire
pressure monitor only functions if the correct
sensors are installed on all wheels.
Information on tire pressures is displayed in
the multifunction display.After a few minutes
of driving, the current tire pressure of each
tire is shownintheServicemenu of the
multifunction display. For further information
on displaying this message, refer to the
"Checking the tire pressure electronically"
section (Ypage 322).
Important safety notes
GWARNING
Each tire, including the spare (if provided),
should be checked at least once a month
when cold and inflated to the pressure
recommended by the vehicle manufacturer
on the Tire and Loading Information placard
on the driver's door B-pillar or the tire
pressure label on the inside of the fuel filler
flap. If your vehicle has tires of a different size
than the size indicated on the Tire and Loading
Information placard or the tire pressure label,
you should determine the proper tire pressure
for those tires.
As an added safety feature, your vehicle has
been equipped with a tire pressure monitoring
system (TPMS) that illuminates a low tire
pressure telltale when one or more of your
320Tire pressure
Wheels and tires

The tire pressure values indicated by the on-
board computer may differ from those
measured at a gas station with a pressure
gauge. The tire pressures shown by the on-
board computer refer to those measured at
sea level. At high altitudes, the tire pressure
values indicated by a pressure gauge are
higher than those shown by the on-board
computer.Inthis case, do not reduce the tire
pressures.
The operation of the tire pressure monitor can
be affected by interference from radio
transmitting equipment (e.g. radio
headphones, two-way radios) that may be
being operated in or near the vehicle.
Checking the tire pressure
electronically
XMake sure that the SmartKey is in position
2(Ypage 137) in the ignition lock .
XPress theorbutton on the
steering wheel to select theService
menu.
XPress theorbutton to select
Tire Pressure.
XPress thebutton.
The current tire pressure of each tire is
shown in the multifunction display.
If the vehicle has been parked for over
20 minutes, theTire pressure will be
displayed after driving a few
minutesmessage appears.
After a teach-in process, the tire pressure
monitor automatically detects new wheels or
new sensors. As long as a clear allocation of
the tire pressure value to the individual
wheels is not possible, theTire Pressure
Monitor Activedisplay message is shown
instead of the tire pressure display. The tire
pressures are already being monitored.
Tire pressure monitor warning
messages
If the tire pressure monitor detects a pressure
loss in one or more tires, a warning message
is shown in the multifunction display and the
yellow tire pressure monitor warning light
comes on.
RIf theCorrect Tire Pressuremessage
appears in the multifunction display, the
tire pressure in at least one tire is too low
and must be corrected at the next
opportunity.
RIf theCheck Tire Pressure Soon
message appears in the multifunction
display, the tire pressure in one or more
tires has dropped significantly and the tires
must be checked.
RIf theTire Pressure Warning Tire
Failuremessage appears in the
multifunction display, the tire pressure in
one or more tires has dropped suddenly
and the tires must be checked.
Observe the instructions and safety notes in
the display messages in the "Tires" section
(Ypage 234).
iIf the wheel positions on the vehicle are
rotated, the tire pressures may be
displayed for the wrong positions for a
short time. This is rectified after a few
minutes of driving, and the tire pressures
are displayed for the correct positions.
Restarting the tire pressure monitor
When you restart the tire pressure monitor,
all existing warning messages are deleted and
the warning lamps go out. The monitor uses
the currently set tire pressures as the
reference values for monitoring. In most
cases, the tire pressure monitor will
automatically detect the new reference
values after you have changed the tire
pressure. However, you can also define
reference values manually as described here.
The tire pressure monitor then monitors the
new tire pressure values.
322Tire pressure
Wheels and tires

!To prevent damage to the paintwork, hold
the wheel securely against the wheel hub
while screwing in the first wheel bolt.
XCleanthe wheel and wheel hub contact
surfaces.
XPlace the new wheel on the wheel hub and
push it on.
XTighten the wheel bolts until they are
finger-tight.
Lowering the vehicle
GWARNING
The wheels could work loose if the wheel nuts
and bolts are not tightened to the specified
tightening torque. There is a risk of accident.
Have the tightening torque immediately
checked at a qualified specialist workshop
after a wheel is changed.
XPlace the ratchet wrench onto the hexagon
nut of the jack so that the lettersABare
visible.
XTurn the ratchet wrench until the vehicle is
once again standing firmly on the ground.
XPlace the jack to one side.
XTighten the wheel bolts evenly in a
crosswise pattern in the sequence
indicated (to). The tightening torque
must be96 lb-ft (130 Nm).
XTurn the jack back to its initial position.
XStow the jack and the rest of the vehicle
tools in the vehicle again.
XCheck the tire pressure of the newly
mounted wheel and adjust it if necessary.
Observe the recommended tire pressure
(Ypage 316).
iVehicles with tire pressure monitor: all
wheels mounted must be equipped with
functioning sensors.
Wheel and tire combinations
General notes
!For safety reasons, Mercedes-Benz
recommends that you only use tires and
wheels which have been approved by
Mercedes-Benzspecifically for your
vehicle.
These tires have been specially adapted for
use with the control systems, such as ABS
or ESP®, and are marked as follows:
RMO=Mercedes-BenzOriginal
RMOE=Mercedes-BenzOriginal Extended
(tires featuring run-flat characteristics)
RMO1=Mercedes-BenzOriginal (only
certain AMG tires)
Mercedes-Benz Original Extended tires
may only be used on wheels that have been
specifically approved by Mercedes-Benz.
Only use tires, wheels or accessories
tested and approved by Mercedes-Benz.
Certain characteristics, e.g. handling,
340Wheel and tire combinations
Wheels and tires