lights MERCEDES-BENZ CLA 2018 Owner's Manual

If the battery voltage is too low, the rear window
defroster may switch off.
Activating/deactivating X
Turn the SmartKey to position H in the igni-
tion lock ( Y
page 122). X
Press the l button.
The indicator lamp in the l button lights
up or goes out.
Problems with the rear window defroster Problem
Possible causes/consequences and P Solutions
The rear window
defroster has deactiva-
ted prematurely or can-
not be activated. The battery has not been sufficiently charged. X
Switch off any consumers that are not required, e.g. reading lamps,
interior lighting or the seat heating.
When the battery is sufficiently charged, the rear window defroster
can be activated again.
Switching air-recirculatio nm ode
on/off
General notes You can deactivate the flow of fresh air if
unpleasant odors are entering the vehicle from
outside. The air already inside the vehicle will
then be recirculated.
If you switch on air-recirculation mode, the win-
dows can fog up more quickly, in particular at
low temperatures. Only use air-recirculation
mode briefl ytop revent the window sf rom fog-
ging up.
The operation of air-recirculation mode is the
same for all control panels.
Activating/deactivating X
Turn the SmartKey to position H in the igni-
tion lock ( Y
page 122).X
To activate: press the

i If you activate the residual heat function at
high temperatures, only the ventilation wil lb e
activated. The blower runs at mediu ms peed.
i You cannot use the ventilation to cool the
vehicle interior to at emperature lowe rt han
the outsid et emperature.
Activating/deactivating X
Turn the SmartKey to position Z in the igni-
tion lock or remove it ( Y
page 122).X
Press the K button.
The indicator lamp in the K button lights
up or goes out.
The indicator lamp in the button indicates that
the respective function is activated.
i Residua lh eat is deactivated automatically:R
after approximately 30 minutes R
when the ignition is switched on R
if the battery voltage drops
Air vents
Important safety notes
G WARNING
Very hot or very cold air can flow from the air
vents. This could resul tinb urns or frostbite in
the immediate vicinity of the air vents. There
is ar isk of injury.
Make sure that all vehicle occupants always
maintain as ufficient distance to the air out-
lets. If necessary ,r edirect the airflow to
another area of the vehicle interior.
In order to ensure the direct flow of fresh air
through the air vents into the vehicle interior,
please observe the following notes: R
keep the air inlet between the windshield and
the hood free of blockages, such as ice, snow
or leaves. R
never cover the air vents or air intake grilles in
the vehicle interior.
i For optimal climate control in the vehicle,
open the air vents completely and set the
adjusters to the central position. Setting the air vents
C
Side window defroster vent D
Side air vent X
To open as ide air vent: turn the adjuster in
side air vent D to the left. X
To close as ide air vent: turn the adjuster in
side air vent D clockwise as far as it wil lg o.
i The center and rear air vents are adjusted in
the same way.120
Ai rv ents
Climate control

operates independently of the ECO start/stop
automatic engine switch-off function.
Key positions with the Start/Stop button
C
Start/Stop buttonD
Ignition lock
As soon as the ignition is switched on, all the
indicator lamps in the instrument cluster light
up.
For further information on situations in which an
indicator lamp either fails to go out after the
engine is started or lights up while driving,
please refer to "Warning and indicator lamps in
the instrument cluster" ( Y
page 219).
If Start/Stop button C has not yet been
pressed, this is the same as the SmartKey being
removed from the ignition. X
To switch on the power supply: press
Start/Stop button C once.
The power supply is switched on. You can now
activate the windshield wipers, for example.
The power supply is switched off again if: R
the driver's door is opened and R
you press Start/Stop button C twice when in
this position X
To switch on the ignition: press Start/Stop
button C twice.
The ignition is switched on.
If you press Start/Stop button C once when
in this position, the ignition is switched off
again.
Removing the Start/Stop button
You can remove the Start/Stop button from the
ignition lock and start the vehicle as normal
using the SmartKey.
You can only switch between Start/Stop button
mode and SmartKey operation when the vehicle
is stationary. You must also engage park position ] .X
Remove Start/Stop button C from ignition
lock D .
You do not have to remove the Start/Stop but-
ton from the ignition lock when you leave the
vehicle. You should, however, alway st ake the
SmartKey with you when leaving the vehicle. As
long as the SmartKey is in the vehicle: R
the vehicle can be started using the Start/
Stop button R
the electrically powered equipment can be
operated
Starting the engine
Important safety notes
G WARNING
If children are left unsupervised in the vehicle,
they could: R
open the doors, thus endangering other
people or road users. R
get out and disrupt traffic. R
operate the vehicle's equipment.
Additionally, children could set the vehicle in
motion if, for example, they: R
release the parking brake. R
shifting the automatic transmission out of
park position P R
Start the engine.
There is ar isk of an accident and injury.
When leaving the vehicle, alway st ake the
SmartKey with you and lock the vehicle. Never
leave children or animals unattended in the
vehicle. Always keep the SmartKey out of
reach of children.
G WARNING
Combustion engines emit poisonous exhaust
gases such as carbon monoxide. Inhaling
these exhaust gases leads to poisoning. There
is ar isk of fatal injury. Therefore never leave
the engine runnin gine nclosed spaces with-
out sufficient ventilation. Driving 123
Driving and parking Z

Deactivating or activating th eE CO
start/stop function X
To deactivate : press EC Ob utto n C .
Indicator lamp D goe so ut .X
To activate : press EC Ob utto n C .
Indicator lamp D lights up.
If indicator lamp D is off, th eE CO start/sto p
function has bee nd eactivated manually or as
th er esult of am alfunction .T he engin ew ill then
no tbes witched of fa utomatically when th ev ehi-
cl es to ps . AMG Performance exhaust syste m
(Mercedes-AMG vehicles )You can choos eb etween differen tA MG Per -
formanc ee xh aus ts ystem volume su sin gt he
position of th ee xh aus tf lap .
Each time you start th ee ng in ew it ht he Smart -
Key or th eS ta rt/Sto pb utton, th eq uietest set -
ting is activated.
Settin gt he volume : X
Press butto n C .
If you selec tt he loudest setting ,i nd icator
lamp D lights up.
Problem sw it ht he engin eProblem
Possible causes/consequences an d P Solutions
The engin ed oe sn ot
start . The HOLD function or Distanc eP ilo tD ISTR ONIC is activated.X
Deactivat et he HOLD function ( Y
page 157) or Distanc eP ilo t
DISTRONIC ( Y
page 155).X
Tr yt os ta rt th ee ng in ea gain .
The engin ed oe sn ot
start .T he starter moto r
can be heard. R
There is am alfunction in th ee ng in ee lectronics.R
There is am alfunction in th ef ue ls upply.
Before attemptin gtos ta rt th ee ng in ea gain :X
Tur nt he SmartKey bac ktop osition Z in th ei gnition lock.
or X
Press th eS ta rt/Sto pb utto nr epeatedly until all indicator lamp si n
th ei nstrument cluster go out .X
Tr yt os ta rt th ee ng in ea gain .A vo id excessivel yl on ga nd frequent
attempt stos ta rt th ee ng in east he se will drain th eb attery.
If th ee ng in ed oe sn ot start after severa la ttempts:X
Consult aq ualified specialis tw orkshop .Driving 127
Driving an dp ark in g Z

In addition, the current drive program settings
are displaye db riefl yint he multimedia system
display.
i In af ew countries, the ECO start/stop func-
tion is deactivated at the factory due to the
available fuel grade .Int his case, the ECO
start/stop function is not available in any
drive program, regardless of the display in the
multimedia system display.
Available drive programs:
C Comfort Comfortable and economi-
cal driving characteristics
S Sport Sporty driving characteris-
tics
I Individual Individual settings
E Economy Particularly economical
driving characteristics
Additional information for drive programs
( Y
page 134).
You can also change gear yourself using the
steering wheel paddle shifters. For further infor-
mation on the manua ld rive program
( Y
page 136).
DYNAMIC SELECT controller
(Mercedes-AMG vehicles) Use the DYNAMIC SELECT controller to change
the drive program. Depending on the drive pro-
gram selected the following vehicle character-
istics wil lc hange:R
the drive R
the transmission management R
ESP ®
R
the suspension (vehicles with AMG adaptive
sport suspension system) R
the availability of the ECO start/stop function R
the availability of gliding mode
Each time you start the engine with the Smart-
Key or the Start/Stop button, drive program C is
activated. For further information abou ts tarting
the engine, see ( Y
page 125). X
Turn DYNAMIC SELECT controller C as many
times as necessary until the desire dd rive
program is selected.
The selected drive program appears in the
multifunction display. After five seconds the
display goes out and the status icon of the
selected drive program appears.
The drive program indicator on DYNAMIC
SELECT controller C lights up in red.
Available drive programs:
I Individual Individual settings
C Comfort Comfort-oriented, opti-
mum-economy engine and
transmission settings
S Sport Sporty engine and trans-
missio ns ettings
S+ Sport Plus Particularly sporty trans-
missio ns ettings
Race
Maximu ms portiness and
engine and transmission
settings suitable for the
racetrack
Additional information for drive programs
( Y
page 134).
You can also change gear yourself using the
steering wheel paddle shifters. For further infor-
mation on the manua ld rive program
( Y
page 136).DYNAMIC SELEC Tc on trolle r( Mercedes-AMG vehicles) 129
Driving and parking Z

the SmartKe yf ro mt he ignition, the automatic
transmission shifts to ] automatically.
With the Start/Sto pb utton: if yo ut he no pe n
the driver's door or the front-passenge rd oo r,
the automatic transmission shifts to ] auto-
matically.
If yo uw an tt he automatic transmission to
remai ninn eutral \\ ,e .g .w he nh av in gt he vehi-
cle cleane dinana ut omatic car wash with a
towing system: X
Vehicle sw it ht he Start-Sto pb utton:
remove the Start-Stop button fro mt he igni-
tio nl oc k.X
Insert the SmartKe yi nto the ignition lock.X
Al lv eh icles: switch the ignition on.X
Depres st he brake peda la nd kee pi t
depressed. X
Engage neutral \\ .X
Releas et he brake pedal.X
Releas et he electri cp ar king brake.X
Switch off the ignition and leav et he SmartKey
in the ignition lock.
Electric parking brake
General notes
G WARNING
If yo ul eave children unsupervised in the vehi-
cle ,t he yc ould se titinm otion by ,f or example:R
release the parking brake. R
shift the automatic transmission ou toft he
parking position P .R
start the engine.
In addition, the ym ay operate vehicl ee quip-
ment and become trapped .T here is ar is ko f
an accident and injury.
When leaving the vehicle, always take the
SmartKe yw it hy ou and lock the vehicle. Never
leav ec hildren unsupervised in the vehicle. The functio noft he electric parking brake is
dependent on the on-board voltage. If the on-
boar dv oltag eisl ow or there is am al functio ni n
the system, it ma yn ot be possibl etoa pply the
release dp ar king brake. X
If thi sist he case, onl yp ar kt he vehicl eo n
level ground and secur eittop revent it rolling
away. X
Shift the automatic transmission to position
] .
It ma yn ot be possibl etor elease an applied
parking brake if the on-board voltag eisl ow or
there is am al functio nint he system. Contact a
qualified specialis tw or kshop.
The electric parking brake performs af un ction
tes tatr egular intervals whil et he engine is
switched off .T he sound st ha tc an be he ar dw hile
thi siso ccurring ar en ormal.
Applyin gorr eleasing manually
X
To engage: push handle C .
When the electric parking brake is applied,
the red I (USA only) or $ (Canada
only) indicator lamp lights up in the instru-
ment cluster.
Th ee le ctric parking brake can also be applied
when the SmartKe yisr emoved.X
To release: pull handle C .
The red I (USA only) or $ (Canada
only) indicator lamp in the instrument cluster
goes out.
Th ee le ctric parking brake can onl yb e
released: R
if the SmartKe yisinp osit ion G or H in
the ignition lock ( Y
page 122 )o rR
if the ignition wa ss wi tched on using the
Start/Stop button142
Parking
Driving an dp arking

Sport mode
The firmer settin goft he suspension tuning in
Sport mode ensures even better contact with
the road. Select this mode when employing a
sporty driving style, e.g. on winding country
roads. X
Press button C .
Indicator lamp D lights up. You have selected
Sport mode.
The AMG Suspension System SPORT
mes-
sage appears in the multifunction display.
Comfort mode In Comfort mode, the driving characteristics of
your vehicle are more comfortable. Select this
mode if you favor am ore comfortable driving
style, but also when driving fast on straight
roads, e.g. highways. X
Press button C again so that indicator
lamp D goes out.
You have selected Comfort mode.
The AMG
Suspension System COMFORT mes-
sage appears in the multifunction display.
4MATIC
! Never tow the vehicle with one axle raised.
This may damage the differential. Damage of
this sort is not covered by the Mercedes-Benz
Limited Warranty. All wheels must remain
either on the ground or be fully raised.
Observe the instructions for towing the vehi-
cle with all wheels in full contact with the
ground.
4MATIC, together with ESP ®
,i mproves the trac-
tion of your vehicle whenever ad rive wheel
spins due to insufficient grip. If you fail to adapt your driving style, 4MATIC can
neither reduce the risk of accident nor override
the laws of physics. 4MATIC cannot take
account of road, weather and traffic conditions.
4MATIC is only an aid. You are responsible for
the distance to the vehicle in front ,f or vehicle
speed, for braking in good time and for staying in
your lane.
If ad rive wheel spins due to insufficient grip: R
Only depress the accelerator pedal as far as
necessary when pulling away. R
Accelerate less when driving.
i In wintry driving conditions, the maximum
effect of 4MATIC can only be achieved if you
use winter tires (M+S tires), with snow chains
if necessary.
DYNAMIC BODY CONTROL
General notes DYNAMI CB ODY CONTROL offers improved
driving comfort and continuously controls the
calibration of the dampers. The
damping characteristics adapt to the current
operating and driving situation.
The damping is tuned individually to each wheel
and depends on: R
your driving style, e.g. sporty R
the road surface conditions R
the drive program selected
The drive program can be set using the
DYNAMI CS ELECT button ( Y
page 128).
Selecting Comfort mode In the Comfort drive program, the driving char-
acteristic sofy our vehicle are more comforta-
ble. Therefore, select this drive program if you
prefer am ore comfortable driving style. Also
select the Comfort drive program when driving
fast on straight roads, e.g. on straight stretches
of highway. X
Press DYNAMI CS ELECT button ( Y
page 128)
as many times as necessary until the Com-
fort drive program is selected.160
Driving systems
Driving and parking

becomes .W hen the minimum distance is
reached, you hear ac ontinuous warning tone.
Deactivating or activating Parking
Assist PARKTRONIC
C
Indicator lampD
Deactivates or activates Parkin gA ssist
PARKTRONIC If indicator lamp C is lit, Parkin gA ssist
PARKTRONI Ci sd eactivated.
i Parkin gA ssist PARKTRONI Cisa utomati-
cally activated when you turn the SmartKey to
position 2 in the ignition lock.
Problems with Parking Assist PARKTRONIC Problem
Possible causes/consequences and P Solutions
Only the red segments in
the Parkin gA ssist
PARKTRONI Cw arning
displays are lit. You also
hear aw arning ton ef or
approximately two sec-
onds.
Parkin gA ssist
PARKTRONI Ci st hen
deactivated and the indi-
cator lamp on the
PARKTRONI Cb utton
lights up. Parkin gA ssist PARKTRONI Ch as malfunctioned and has been deacti-
vated. X
If problems persist ,h ave Parkin gA ssist PARKTRONI Cc hecked at a
qualified specialist workshop.
Only the red segments in
the Parkin gA ssist
PARKTRONI Cw arning
displays are lit. Parking
Assist PARKTRONI Ci s
then deactivated. The Parkin gA ssist PARKTRONI Cs ensor sa re dirty or ther eisi nter-
ference. X
Clean the Parkin gA ssist PARKTRONI Cs ensor s( Y
page 265).X
Switc ht he ignition back on.
The problem may be caused by an external source of radio or ultra-
sound waves. X
Check to see if Parkin gA ssist PARKTRONI Cw orks at ad ifferent
location. Driving systems 163
Driving and parking Z

Any unauthorized modification to thi sd ev ice
could voi dt he user’ sa ut hority to operate the
equipment.
Radar sensors The rada rs ensors for Blind Spo tA ssist ar ei nte-
grated into the rea rb um per. Make sure tha tt he
bumpers ar ef re ef rom dirt, ice or slush. The
sensors must not be covered ,f or exampl eb y
cycle racks or overhanging loads. Following a
severe impact or in the event of damage to the
bumpers, have the functio noft he rada rs ensors
checked at aq uali fied specialist workshop.
Blind Spo tA ssist ma ynol on ge rw or kp roperly.
Monitorin gr ang eoft he sensorsIn particular, the detection of obstacle sc an be
impaired if: R
ther eisd ir tont he sensors or anything else
covering the sensors R
ther eisp oo rv isibility ,e .g .d ue to fog ,h eavy
rain or snow R
an arrow vehicl et raveling in front, e.g .a
motorbike or bicycle R
the roa dh as ver yw id el an esR
the roa dh as narrow lanesR
yo ua re not driving in the middl eoft he laneR
ther ea re barriers or othe rr oa db ou ndaries
Vehicles in the monitoring range ar et hen not
indicated.
Blind Spo tA ssist monitors the area up to 10 ft
(3 m) behind your vehicl ea nd directl yn ext to it.
If the lanes ar en arrow ,v ehicles driving in the
lane beyond the lane next to your vehicl em a y be
indicated ,e specially if the vehicles ar en ot driv-
ing in the middl eoft hei rl an e. Thi sm ay be the
cas eift he vehicles ar ed riving on the inne rs id e
of thei rl an e.
Due to the nature of the system: R
warning sm ay be issued in error when driving
close to crash barriers or similar solid lane
borders. R
warning sm ay be interrupte dw he ny ou are
driving alongsid ep ar ticularly long vehicles,
such as trucks, for ap rolonge dt ime. Warning display
C
Warning display
Blind Spo tA ssist is not active at speed sb elow
approximatel y20m ph (30 km/h). Vehicles in
the monitoring range ar et hen not indicated.
Whe nB lind Spo tA ssist is activated ,i ndicator
lamp C in the exterio rm irrors lights up yellow
at speed sofupto20m ph (30 km/h). At speeds
above 20 mph (30 km/h), the indicator lamp
goe so ut and Blind Spo tA ssist is operational.
If av ehicl eisd et ecte dw it hi nt he blind spot
monitoring range at speed sa bo ve 20 mph
(30 km/h), warning lamp C on the correspond-
ing side lights up red .T hi sw ar ning is always
emitted when av ehicl ee nters the blind spot
monitoring range from behind or from the side.
Whe ny ou overtake av ehicle, the warning only
occurs if the difference in speed is less than
7m ph (12 km/h).
The yellow indicator lamp goe so ut if reverse
gear is engaged .Int hi se vent, Blind Spo tA ssist
is no longe ra ctive.
The brightness of the indicator/warning lamps
is adjusted automaticall ya ccording to the ambi-
ent light.
Collisio nw ar ning
If av ehicl eisd et ecte dint he monitoring range of
Blind Spo tA ssist and yo us wi tch on the corre-
sponding turn signal, ad ouble warning tone
sounds. Re dw ar ning lamp C flashes. If the turn
signa lr emains on, vehi cles detecte da re i ndica-
ted by the flashing of red warning lamp C .
There ar enof ur the rw ar ning tones.Driving systems 173
Driving an dp arking Z

R
Distance Pilo tD ISTRONICR
ASSYST PLU Ss ervic ei nterva ld isplay
Switchin gt he additional speedometer
on/off If the additional speedomete riss wi tched on,
the spee diss hown in the status ba rint he mul-
tifunctio nd isplay instea doft he outside tem-
perature.
The spee dd isplay is invers etot he speedome-
ter. X
Press the Y or e button on the steering
whee ltos elect the Sett. menu.X
Press the d or c button to select the
Instrumen tC luster submenu.X
Press v to confirm.X
Press the d or c button to select the
Speedometer [km/h] or Speedometer
[mph] function.
Yo uw il ls ee the selecte ds etting: On or Off .X
Press the v button to save the setting.
Selecting permanent display The Permanent Display: functio na llow sy ou
to choose whether the multifunctio nd isplay
always shows the outside temperatur eort he
speed.
The spee dd isplay is invers etot he speedome-
ter. X
Press the Y or e button on the steering
whee ltos elect the Sett. menu.X
Press the d or c button to select the
Instr. Cluster submenu.X
Press v to confirm.X
Press the d or c button to select the
Permanent Display: function.
The current setting, Outsid eT emperature
or Speedometer [km/h] / Speedometer
[mph] ,a ppears .X
Press the v button to save the setting.
Lights
Switchin gt he daytime runnin gl amps on/
off
Thi sf un ctio ni sn ot availabl einC an ada.X
Press the Y or e button on the steering
whee ltos elect the Sett. menu.X
Press the d or c button to select the
Light submenu. X
Press v to confirm. X
Press the d or c button to select the
Daytim eR unnin gL ights function.
If the Daytime Running Lights functio nh as
been switched on, the multifunctio nd isplay
shows the cone of light and the