key MERCEDES-BENZ CLK-Class 2009 C208 Comand Manual

42 System settingsSystem settings
The respective tones are activated or
deactivated. You hear the tone when
you activate it.

Press the
Back
soft key.
The System settings menu will appear.
The setting is saved.

In the System settings menu, press the Display
soft key.
You can use the following functions:
set the display dimming characteristics

adjust the display brightness
Setting the display dimming
characteristics
Push the joystick to
G
or g
to
select an entry.
Day modeThe display is continuously set to
daylight design.Night modeThe display is continuously set to night-
time design.AutomaticThe display changes depending on the
ambient light sensor in the vehicle.

Press E
.
The setting is applied. The System
settings menu will appear.
Adjusting the display brightness 
Press the
Bright.
soft key.

Push the joystick to H or h
direction to adjust the brightness.
or
Press the
Bright
. soft key longer than
2 seconds.
The display brightness changes
gradually. When the slider reaches the
end of the left or right border, it starts
moving into the opposite direction.The display brightness changes
gradually. When the slider reaches the
end of the left or right border, it starts
moving into the opposite direction.
Selecting display settingsOption
Symbol
Display mode selected
_
Display mode not
selected
-
209_MY09_A_US.book Seite 42 Montag, 26. Mai 2008 6:12 18

43 System settings
System settings

Release the
Bright.
soft key
when
the desired brightness is reached.
Confirming the setting
Press the
Back
soft key.
or
Press E
.
The brightness setting is applied.

Press the
Scr.Off
soft key.
The screen is switched off.

Press any soft key or button.The screen is switched on again.

In the System settings menu, press the Reset
soft key.
The Reset inquiry menu will appear.
No

is highlighted.
If you do not wish to reset to the factory
settings
Press the
Back
soft key or press E
.
The System settings menu will appear.
Accepting the factory settings
Push the joystick to H or h
direction to select
Yes
.

Press E
.
The inquiry
Do you really want to
reset?
will appear.

Select
Yes
.
The message
All data has been
reset.
COMAND will now
restart. will appear.
Switching the screen off or onResetting all settings to the factory
settingsiAll your personal data, e.g. Last desti
-
nation entries or Radio main menu pre
-
set entries, will be deleted.
iThe factory settings are:Time - Central TimeLanguage - Instrument clusterVerification tone - OnNotification tone - OnDisplay setting - Automatic
209_MY09_A_US.book Seite 43 Montag, 26. Mai 2008 6:12 18

47 Audio
Audio operation

If an audio submenu is displayed, press
the
Back
soft key until the Audio menu
is displayed.
or
Press A again.

In the Audio menu, press the soft key
for the desired audio source.
Switching On
Press J.The system mutes the active audio
source and the
ß symbol is displayed in
the status bar. The soft keys on the left
side are greyed out in some submenus.
Switching off
Press J again.
iThe
CD
or the
MP3
soft key is
available, depending on the medium
inserted in the CD AUDIO slot.The
CD
soft key is available if a CD
changer is connected to the COMAND.
Selecting an audio sourceMuting
iCOMAND will also deactivate if you
Press A, B, g
, h

Change the volume at COMAND or
the multifunction steering wheel

Operate the joystick

Press any keypad button except
#

Press j or k at the
multifunction steering wheel if the
audio menu is selected

Press any soft key.
209_MY09_A_US.book Seite 47 Montag, 26. Mai 2008 6:12 18

48 AudioRadio operation

Radio operation

In the Audio menu, press the
Radio
soft
key.
The Radio main menu will appear. The
station last tuned to will begin to play.
Radio main menu1Soft key assignment2Main area3Status barSwitching back to the Audio menu
Press the
Back
soft key.
You can select between FM-, AM- and WB-
Band.AM Band
In the FM Radio main menu, press the FM/AM
soft key until “AM” is displayed in
the status bar.
The AM station last tuned to will begin to
play. The frequency will appear in the
display.Switching back to FM band
Press the
FM/AM
soft key.
The station last tuned to will begin to
play.
Switching to radio operation
iThe
Sound
soft key is available if
COMAND is equipped with a sound
amplifier.
Changing the Radio band
Frequency band
Frequency range
FMAM
87.7 - 107.9 MHz530 - 1710 kHz
209_MY09_A_US.book Seite 48 Montag, 26. Mai 2008 6:12 18

49 Audio
Radio operation
Weather Band WB
In the FM or AM Radio main menu,
press the
WB soft key.
An automatic scan is starting and the

COMAND plays and displays the
channel of the first strong WB station.
Switching back to FM or AM band
Press the
FM/AM
soft key.
or
Press the
WB soft key
The station last tuned to will begin to
play.
Switching back to the Audio menu
Press the
Back
soft key.
The Weather Band WB station will con
-
tinue to play.
You can use the following functions:
Automatic seek tuning
( page
49)

Manual tuning
( page
50)

Station selection via direct frequency
entry (FM, AM)
( page
50)

Preset station selection via number
keypad
( page
51)

Automatic station scan (FM, AM) ( page
51)

Station selection from the FM/AM
preset menu
( page
54)

Station selection from the FM/AM
Autostore presets
( page
54)
Automatic seek tuningVia memory presetsFM and AM bands
Press g or h.
or
Push the joystick to g
or G.
The radio will tune to the frequency
assigned to the next memory location.
If none has been set by you, the radio
will not change the station.
iWith the number keys 1 - 7 it is pos
-
sible to choose a channel.The message
No channel
will appear if
the system could not detect a channel.
Selecting a station
iMemory
must be activated in the Audio
search function menu, which appears
in the multifunction display.
Access this menu from the Settings...
menu via the Vehicle
submenu
( page
30)
. For additional
information refer to separate
Operator’s Manual instructions.
209_MY09_A_US.book Seite 49 Montag, 26. Mai 2008 6:12 18

50 AudioRadio operationVia frequency
Press g or h.
or
Push the joystick to g
or G.
The radio will tune to the next
receivable station (FM, AM) or channel
(WB) of descending/ascending
frequency depending on the direction
of seek.
WB direct channel selection
Press a number key 1 through 7.
Manual tuning (FM, AM)
Activate the desired wave band ( page
48)
.

Press g or h longer than 2 se
-
conds.The function rapidly scans the
frequencies.

Press g or h repeatedly to
change the frequency step by step.
or
Push the joystick to H or h.Each
push of the joystick
will change
the frequency by one step.
FM BandThe frequency displayed will change in in
-
crements of 0.2 MHz.
AM BandTuning will take place in increments of
10
kHz.
Station selection via direct frequency
entry (FM, AM)E.g.: 102.7 MHz in the FM band
Activate the desired wave band ( page
48)
.

Press *.An input line will appear.

Enter the desired frequency with the
number keys within 8 seconds, e.g.
1027 for 102.7 MHz.
iFrequenc.
must be activated in the
Audio search function menu, which
appears in the multifunction display.
Access this menu from the Settings...
menu via the Vehicle
submenu
( page
30)
. For additional
information refer to separate
Operator’s Manual instructions.
iThe selected channel is not shown in
the status line.
209_MY09_A_US.book Seite 50 Montag, 26. Mai 2008 6:12 18

51 Audio
Radio operation
The station you have selected will
begin to play.
FM, AM bandEntries outside the frequency range are
not accepted. The message
Please
observe frequency range 87.7 - 107.9
MHz
will appear briefly.
Preset station selection via number
keypadFM- and AM-Bands
Press one of the number keys, such as
2 briefly.The radio will tune to the frequency as
-
signed to that memory location. If none
has been set by you, the radio will not
change the station.
Automatic station scan (FM, AM)The stations on the same band (FM, AM)
can be scanned one after the other for 8
seconds each.Start scan function
Activate the desired wave band ( page
48)
.

Press the
Scan
soft key.
Frequency band
Frequency range
FMAM
87.7 - 107.9 MHz530 - 1710 kHz
iIf you do not make another entry within
8 seconds, the function will be canceled
and you will continue listening to the
station last tuned to.
iFM and AM presets are independent
and can only be accessed while in the
corresponding band.Saving stations for FM and AM ( page
52)
.
iIn the AM band, two search runs take
place. During the first run, stations with
good reception are played. During the
second run, stations with weaker
reception are played.
209_MY09_A_US.book Seite 51 Montag, 26. Mai 2008 6:12 18

52 AudioRadio operation
The scan function will begin.
End scan function and play a station
Press the
Scan
soft key again if you
hear the desired station.
orThe scan function stops automatically
when the first station received has been
scanned twice.
You can use the following functions:
Saving stations manually (FM, AM)

Saving stations automatically FM, AM ( page
53)

Selecting a station from the FM/AM
preset menu
( page
54)

Selecting a station from the FM/AM
Auto presets
( page
54)
Saving stations manually (FM, AM) In the Radio main menu
Activate the desired wave band ( page
48)
.

Press one of the number keys, e.g. 2,
longer than 2 seconds.You will hear a verification beep if the
beep tones option was activated in the
system settings
( page
41)
.
The radio saves the current station at
the memory preset selected. The me
-
mory preset selected will appear in the
status bar, e.g.
FM2
.
On the memory list
Activate the desired wave band ( page
48)
.

Press the
Presets
soft key.
The memory Preset menu will appear.
Memory functions
iThere are 10
presets available (1 -
9, 0).
An existing entry is overwritten in the
memory list when a new input is given.
209_MY09_A_US.book Seite 52 Montag, 26. Mai 2008 6:12 18

53 Audio
Radio operation

Push the joystick to H, h or g,
G to highlight the desired memory
preset.

Press
E
longer than 2
seconds.
You will hear a verification beep if the
beep tones option was activated in the
system settings
( page
41)
.
The current station will be saved at the
memory preset selected.
You will see the Radio main menu
automatically after 8 seconds

if you press the
Back
soft key.
Saving stations automatically (FM, AM)
Activate the desired wave band ( page
48)
.

Press the
Autost.
soft key
.
The autostore preset menu will appear.

Press E to start
Begin new search
.
The autostore function is active. The
message
Autostore being reloaded

will appear. The radio stores the 10
stations with the strongest signal. The
station frequencies available will
appear in the memory list.
iThere are 2 presets for each of the FM
and AM waveband
standard FM/AM presets (saving
stations manually) and

Auto presets (saving stations
automatically).
The standard FM/AM presets are not
affected by the Auto presets. This is a
second option for storing a station ran
-
ge you are currently receiving.
209_MY09_A_US.book Seite 53 Montag, 26. Mai 2008 6:12 18

54 AudioRadio operationSelecting a station from the preset
menu (FM, AM)
Activate the FM or AM memory ( page
52)
.
You can use one of the following two ways
to select a station from the FM/AM
presets
Press the corresponding number key,
e.g. 3, to select the desired station.
or

Push the joystick to H, h or g,
G to highlight a memory preset in the
FM/AM preset list
( page
52)
.

Press E.In both cases, you will see the main
radio menu
automatically after 8 seconds

if you press the
Back
soft key.
The Radio main menu indicating the
memory preset number.
Selecting a station from the FM/AM
autostore presets
Activate the FM or AM autostore preset
menu
( page
53)
.
You can use one of the following two ways
to select a station from the FM/AM
autostore presets
Press the corresponding number key,
e.g. 3, to select the desired station.
or

Push the joystick to H, h or g,
G to highlight a memory position.

Press E.In both cases, you will see the main
radio menu
automatically after 8 seconds

if you press the
Back
soft key.
iThere are max. 10
presets available (1
- 9, 0).
The autostore function assigns the sta
-
tions to the memory locations in the or
-
der of their reception quality. The
strongest station is available on

preset 1. The number of available

stations depends on the stations avai
-
lable in the area the vehicle is operated
in.
209_MY09_A_US.book Seite 54 Montag, 26. Mai 2008 6:12 18