MERCEDES-BENZ CLK350 2008 C209 Workshop Manual

50 Getting started
Driving
With a smooth motion, pull the belt out
of the seat belt presenter.
Place the shoulder portion of the belt
across the top of your shoulder and the
lap portion across your hips.
Push latch plate1 into buckle3 until
it clicks.
If necessary, tighten the lap portion to
a snug fit by pulling shoulder portion
up.
Proper use of seat belts

Do not twist the belt when fastening.

Adjust seat belt so that the shoulder
portion is located as close as possible
to the middle of the shoulder (it should
not touch the neck). Never pass the
shoulder portion of the belt under your
arm.

Position the lap belt as low as possible
on your hips (over hip joint) and not
across the abdomen.

Place the seat backrest in a position
that is as upright as possible.

Never use a seat belt for more than one
person at a time.

Do not fasten a seat belt around a
person and another object at the same
time.

W he n u sing a se at b el t to s ec ur e i nfa nt
restraints, toddler restraints or chil-
dren in booster seats, always follow the
child seat manufacturer’s instructions.

Check your seat belt periodically
during travel to make sure it is properly
positioned.

Make sure the seat belt is always fitted
snugly. Take special care of this when
wearing loose clothing.
Warning!G
Do not pass belts over sharp edges. They
could tear.
Do not allow the belt to get caught in the
door or in the seat adjustment mechanism.
This could damage the belt.
Never attempt to make modifications to
seat belts. This could impair the effective-
ness of the belts.
Do not bleach or dye seat belts as this may
severely weaken them. In a crash they may
not be able to provide adequate protection.
Damaged seat belts or belts that were highly
stressed in an accident must be replaced.
Contact an authorized Mercedes-Benz
Center.

51 Getting started
Driving
The seat belt presenter slides back:

right after you push the latch plate1
into buckle3 and hear it click.

after approximately 60 seconds if you
do not push latch plate 1 into
buckle3.

if your door is opened.

if you turn the SmartKey in the starter
switch to position 0.

if you release a front seat backrest and
fold it forward.
Starting the engine Automatic transmission
Gearshift pattern for automatic
transmission
PPark position with gear selector lever
lock
RReverse gear
NNeutral
DDrive position
For more information, see “Automatic
transmission” (
page 172).
Warning!G
The seat belt presenter must be retracted
while the vehicle is in motion. Only when the
seat belt presenter is retracted can the seat
belt be properly positioned on the body and
protect the occupant as intended.
Warning!G
Inhalation of exhaust gas is hazardous to
your health. All exhaust gas contains carbon
monoxide (CO), and inhaling it can cause
unconsciousness and possible death.
Do not run the engine in confined areas
(such as a garage) which are not properly
ventilated. If you think that exhaust gas
fumes are entering the vehicle while driving,
have the cause determined and corrected
immediately. If you must drive under these
conditions, drive with at least one window
fully open.

52 Getting started
Driving
Starting with the SmartKey
Make sure the gear selector lever is set
toP.
Do not depress accelerator.
Turn the SmartKey in the starter switch
to position3 (
page 38) and release it
again immediately (“touch-start”).
The engine then starts automatically.
For information on turning off the engine
with the SmartKey, see (
page 60).Starting with KEYLESS-GO*
You can start your vehicle without the
SmartKey in the starter switch using the
KEYLESS-GO start/stop button on the
gear selector lever.
The SmartKey with KEYLESS-GO must be
located in the vehicle.
Make sure the gear selector lever is set
toP.
Do not depress accelerator.
Depress the brake pedal during the
starting procedure.
The gear selector lever lock is released.
KEYLESS-GO start/stop button
1USA only
2Canada only
Press KEYLESS-GO start/stop button
once.
The engine starts if the SmartKey with
KEYLESS-GO is in the vehicle.
For information on turning off the engine
with KEYLESS-GO, see “Turning off the en-
gine with KEYLESS-GO*” (
page 60).
Warning!G
As long as the SmartKey with KEYLESS-GO
is in your vehicle, the vehicle can be started.
Therefore, never leave children unattended
in the vehicle, as they could otherwise acci-
dentally start the engine.
When leaving the vehicle, always take the
SmartKey with KEYLESS-GO with you and
lock the vehicle. Do not leave children unat-
tended in the vehicle, or with access to an
unlocked vehicle.

53 Getting started
Driving
Starting difficulties
If the SmartKey is left in starter switch
position0 for an extended period of time,
it can no longer be turned in the switch. In
this case, the steering is locked.
To unlock, remove SmartKey from
starter switch and reinsert.
If the engine does not start as described,
carry out the following steps:
If you are starting the engine with the
SmartKey, turn SmartKey in starter
switch to position0 and repeat starting
procedure.
If you are starting the engine with
KEYLESS-GO*: Close any doors that
may be open to allow for better detec-
tion of the SmartKey with
KEYLESS-GO*.
Or:
Start the engine with the SmartKey as
radio signals from another source may
be interfering with the SmartKey with
KEYLESS-GO*.
Repeat the starting procedure
(
page 51).
Remember that extended starting at-
tempts can drain the battery.
Get a jump start (page 467).
If the engine does not start after several
starting attempts, there could be a mal-
function in the engine electronics or in the
fuel supply system.
Contact an authorized Mercedes-Benz
Center or call Roadside Assistance.
Parking brake
1Release handle
2Parking brake pedal
Warning!G
When leaving the vehicle, always remove the
SmartKey or SmartKey with KEYLESS-GO*
from the starter switch, take it with you, and
lock the vehicle. Do not leave children unat-
tended in the vehicle, or with access to an
unlocked vehicle. Children could release the
parking brake, which could result in an acci-
dent and/or serious personal injury.


54 Getting started
Driving
Release the parking brake by pulling on
release handle1.
The indicator lamp; (USA only)
or3 (Canada only) in the clock
goes out.
Driving
Depress the brake pedal.
Move gear selector lever to
positionDorR.
Release the brake pedal.
Carefully depress the accelerator
pedal.
After a cold start, the automatic transmis-
sion shifts at a higher engine revolution.
This allows the catalytic converter to reach
its operating temperature earlier.
iWait for the gear selection process to com-
plete before setting the vehicle in motion.
!If you hear a warning signal and the mes-
sage
Release Parking Brake appears in the
multifunction display when driving off, you have
forgotten to release the parking brake.
Release the parking brake (
page 53).
iAt vehicle speeds of approximately 9 mph
(15 km/h), the automatic central locking system
engages and the locking knobs drop down.
The automatic door lock feature can be deacti-
vated (
page 166).
You can open a locked door from the inside.
Open door only when conditions are safe to do
so.
!Simultaneously depressing the accelerator
pedal and applying the brakes reduces engine
performance and causes premature brake and
drivetrain wear.
Warning!G
On slippery road surfaces, never downshift
in order to obtain braking action. This could
result in drive wheel slip and reduced vehi-
cle control. Your vehicle’s ABS will not pre-
vent this type of loss of control.
!Place the gear selector lever in
positionRorP only when the vehicle is stopped
in order to avoid damaging the transmission.
!Do not run cold engine at high engine
speeds. Running a cold engine at high engine
speeds may shorten the service life of the en-
gine.
CLK 63 AMG:
At low engine temperatures below +68°F
(+20°C), the engine’s maximum speed is
restricted in order to protect it from damage.
Avoid driving your vehicle at full speed when the
engine is cold to prevent premature engine wear
and/or diminished comfort.


55 Getting started
Driving
For more information on driving, see “Driv-
ing instructions” (
page 309).
Switching on headlamps
Low beam headlamps
Exterior lamp switch
Turn the exterior lamp switch to
positionB.
The low beam headlamps and the low
beam headlamp indicator lampB in
the instrument cluster comes on
(
page 28).High beam
Combination switch
1High beam
2High beam flasher
Push the combination switch in
direction of arrow1.
The high beam headlamps and the high
beam headlamp indicator lampA in
the instrument cluster comes on
(
page 28).
For more information on headlamps, see
“Lighting” (
page 129).
Warning!G
It is dangerous to shift the gear selector
lever out ofPorN if the engine speed is
higher than idle speed. If your foot is not
firmly on the brake pedal, the vehicle could
accelerate quickly forward or in reverse. You
could lose control of the vehicle and hit
someone or something. Only shift into gear
when the engine is idling normally and when
your right foot is firmly on the brake pedal.
1MOff
2BLow beam headlamps or high
beam headlamps.

56 Getting started
Driving
Turn signals
Combination switch
1Turn signals, right
2Turn signals, left
Press the combination switch in
direction of arrow1or2.
The corresponding turn signal indicator
lampLorK in the instrument
cluster flashes (
page 28).
The combination switch resets
automatically after major steering wheel
movements.
Windshield wipers
Combination switch
1Single wipe
Wiping with windshield washer fluid
2Switching on windshield wipers
Switch on the ignition (page 38).Switching on windshield wipers
Turn the combination switch to the de-
sired position depending on the
intensity of the rain.
0Windshield wipers off
IIntermittent wiping
IINormal wiper speed
IIIFast wiper speed
iTo signal minor directional changes such as
changing lanes, press the combination switch
only to the point of resistance and release. The
corresponding turn signals will flash three times.!Do not operate the windshield wipers when
the windshield is dry. Dust that accumulates on
a windshield might scratch the glass and/or
damage the wiper blades when wiping occurs on
a dry windshield. If it is necessary to operate the
windshield wipers in dry weather conditions, al-
ways operate the windshield wipers with wind-
shield washer fluid (
page 57).

57 Getting started
Driving
Intermittent wiping
Intermittent wiping interval is dependent
on wetness of windshield.
Turn the combination switch to
positionI.
After the initial wipe, pauses between
wipes are automatically controlled by the
rain sensor.Single wipe
Press the combination switch briefly in
direction of arrow1 (
page 56) to
the resistance point.
The windshield wipers wipe one time
without washer fluid.Wiping with windshield washer fluid
Press the combination switch in direc-
tion of arrow1 (
page 56) past the
resistance point.
The windshield wipers operate with
washer fluid.
For information on filling up the washer
reservoir, see “Windshield washer system
and headlamp cleaning system*”
(
page 330).
!Do not leave windshield wipers on an
intermittent setting when the vehicle is taken to
an automatic car wash or during windshield
cleaning. Windshield wipers will operate in the
presence of water sprayed on the windshield,
and windshield wipers may be damaged as a re-
sult.
!If you have set intermittent wiping, dirt on
the surface of the rain sensor or optical effects
may cause the windshield wipers to wipe in an
undesired fashion. This could then damage the
windshield wiper blades or scratch the windows.
You should therefore switch off the windshield
wipers when weather conditions are dry.
iIntermittent wiping is interrupted when the
vehicle is at a standstill and a door is opened.
This protects persons getting into or out of the
vehicle from being sprayed.
Intermittent wiping will be continued when

all doors are closed
and

the gear selector lever is in position D or R
or

the wiper setting is changed using the com-
bination switch.
iTo prevent smears on the windshield, or
noisy/chattering wiper blades, wipe with wind-
shield washer fluid every now and then even
when it is raining.


58 Getting started
Driving
Problems while driving
The engine runs erratically and misfires

An ignition cable may be damaged.

The engine electronics may not be op-
erating properly.

Unburned gasoline may have entered
the catalytic converter and damaged it.
Give very little gas.
Have the problem repaired at an autho-
rized Mercedes-Benz Center as soon as
possible.
The coolant temperature is
above 248°F (120°C)
The coolant is too hot and is no longer
cooling the engine.
Stop the vehicle in a safe location as
soon as possible and turn off the
engine. Allow engine and coolant to
cool off.
Check the coolant level and add
coolant if necessary (
page 328).
In case of accident
If the vehicle is leaking gasoline:
Do not start the engine under any
circumstances.
Notify local fire and/or police
authorities.
If the extent of the damage cannot be
determined:
Contact an authorized Mercedes-Benz
Center or call Roadside Assistance.
If no damage can be determined on the

major assemblies

fuel system

engine mount:
Start the engine in the usual manner.
!If anything blocks the windshield wipers
(leaves, snow, etc.), switch them off
immediately.

For safety reasons, stop the vehicle in a safe
location and,

remove SmartKey from starter switch
or

turn off the engine by pressing the
KEYLESS-GO* start/stop button and
open the driver’s door (with the driver’s
door open, starter switch is in position 0,
same as with SmartKey removed from
starter switch)
before attempting to remove any blockage.

Remove blockage.

Turn the windshield wipers on again.
If the windshield wipers fail to function at all with
the combination switch in positionI,

set the combination switch to the next high-
er wiper speed

have the windshield wipers checked at the
nearest authorized Mercedes-Benz Center.


59 Getting started
Parking and locking
Parking and locking
You have now completed your first drive.
You have properly stopped and parked
your vehicle. End your drive as follows.Parking brake
1Release handle
2Parking brake pedal
Step firmly on parking brake pedal2.
Warning!G
With the engine not running, there is no
power assistance for the brake and steering
systems. In this case, it is important to keep
in mind that a considerably higher degree of
effort is necessary to brake and steer the
vehicle.
Warning!G
Do not park this vehicle in areas where com-
bustible materials such as grass, hay or
leaves can come into contact with the hot
exhaust system, as these materials could be
ignited and cause a vehicle fire.
To reduce the risk of personal injury, or
damage to the vehicle or the vehicle
drivetrain, as a result of vehicle movement,
always do the following before turning off
the engine and leaving the vehicle:

Keep right foot firmly on brake pedal.

Firmly depress parking brake pedal.

Move the gear selector lever to
positionP.

Slowly release brake pedal.

When parked on an incline, always turn
the front wheels towards the road curb.

Turn the SmartKey or the SmartKey with
KEYLESS-GO* to starter switch
position0 and remove, or press
KEYLESS-GO* start/stop button.

Take the SmartKey or the SmartKey with
KEYLESS-GO* with you and lock the
vehicle when leaving.
Warning!G
Engaging the parking brake while the vehicle
is in motion can cause the rear wheels to
lock up. You could lose control of the vehicle
and cause an accident. In addition, the
vehicle’s brake lights do not light up when
the parking brake is engaged.