start stop button MERCEDES-BENZ CLK500 CABRIOLET 2004 A209 Owner's Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2004, Model line: CLK500 CABRIOLET, Model: MERCEDES-BENZ CLK500 CABRIOLET 2004 A209Pages: 464, PDF Size: 5.69 MB
Page 26 of 464
26 At a glanceCenter consoleLower part
Item
Page
1
KEYLESS-GO* start/stop
button
33
2
Soft top switch
218
3
Storage compartment
251
4
Thumbwheel for setting
distance in Distronic*
236
5
Distance warning func-
tion* on/off switch
237
Item
Page
6
Program mode selector for
automatic transmission
163,
164
7
Gear selector lever for
automatic transmission
157
Page 32 of 464
32 Getting startedUnlockingUnlocking with KEYLESS-GO*
If you have the KEYLESS-GO function, your
vehicle checks whether the SmartKey with
KEYLESS-GO is valid when you pull the
door handle. If your SmartKey is valid, the
doors will unlock, and you can open them.
The function of the SmartKey overrules the
KEYLESS-GO function.
Pull the door handle.
The turn signal lamps flash once. The
locking knobs on the doors move up.
If the SmartKey is inside the vehicle, press-
ing the KEYLESS-GO start/stop button on
the gear selector lever corresponds to
turning the SmartKey to the various starter
switch positions.iTo unlock the vehicle, the SmartKey
with KEYLESS-GO must be outside the
vehicle, no further than approx. 3 feet
(1 meter) away from the door.
Warning!
G
When leaving the vehicle, always take the
SmartKey with KEYLESS-GO with you, and
lock the vehicle. Do not leave children unat-
tended in the vehicle, or with access to an
unlocked vehicle. Unsupervised use of vehi-
cle equipment may cause an accident
and/or serious personal injury.
Page 33 of 464
33 Getting started
Unlocking
1KEYLESS-GO start/stop button
The SmartKey with KEYLESS-GO must be
located in the vehicle.
Before you press the KEYLESS-GO
start/stop button, the vehicle’s on-board
electronics have status0 (as with
SmartKey removed).
M a k e s u r e t h e g e a r s e l e c t o r l e v e r i s s e t
toP.
Do not depress the brake pedal.Position 1
Press the KEYLESS-GO start/stop but-
ton once.
This supplies power to some electrical
consumers, such as seat adjustment.Ignition (or position 2)
Press the KEYLESS-GO start/stop but-
ton twice.
This supplies power to all electrical
consumers. All the lamps in the instru-
ment cluster come on.
More information can be found in the
“Controls in detail” section (
page 91).
For information on starting the engine us-
ing the KEYLESS-GO start/stop button,
see “Starting with KEYLESS-GO*”
(
page 44).
iIf you now press the KEYLESS-GO
start/stop button
once again, the ignition (position2)
is switched on.
twice, the power supply is again
switched off.
iIf you now press the KEYLESS-GO
start/stop button once, the power sup-
ply is again switched off.
Page 35 of 464
35 Getting started
Adjusting
Seat adjustment
The seat adjustment switches are located
in each door.
1Head restraint height
2Seat height
3Seat cushion tilt
4Seat fore and aft adjustment
5Backrest tilt
Turn the SmartKey in the starter switch
to position1 or2 (
page 31).
or
Press the KEYLESS GO* start/stop
button once or twice (
page 33).
or
Open the driver’s or passenger door.Seat fore and aft adjustment
Press the switch forward or backward
in the direction of arrow4.
Adjust seat to a comfortable seating
position that still allows you to reach
the accelerator / brake pedal safely.
The position should be as far to the rear
as possible, consistent with ability to
properly operate controls.
A child’s risk of serious or fatal injuries is
significantly increased if the child restraints
are not properly secured in the vehicle and
the child is not properly secured in the child
restraint.
iWhen moving the seat, make sure
there are no items in the footwell or be-
hind the seats. Otherwise you could
damage the seats.
The memory function (
page 116) lets
you store the setting for the seat posi-
tion together with the setting for the
steering wheel and the exterior rear
view mirrors.
Page 38 of 464
38 Getting startedAdjustingSteering wheel adjustment
The stalk for steering wheel adjustment is
located on the steering column (lower left).
1Adjusting steering column, in or out
2Adjusting steering column, up or down
Turn the SmartKey in the starter switch
to position1or2 (
page 31).
or
Press the KEYLESS GO* start/stop
button once or twice (
page 33).
or
Open the driver’s door.Adjusting steering column in or out
Move stalk forward or back in the direc-
tion of arrow 1 until a comfortable
steering wheel position is reached with
your arms slightly bent at the elbow.
Adjusting steering column up or down
Move stalk up or down in the direction
of arrow 2.
Make sure your legs can move freely
and all the displays (incl. malfunction
and indicator lamps) on the instrument
cluster are clearly visible.
Mirrors
Adjust the interior and exterior rear view
mirrors before driving so that you have a
good view of the road and traffic condi-
tions.
Interior rear view mirror
Manually adjust the interior rear view
mirror.
For more information, see “Rear view mir-
ror” (page 168)
iThe memory function (
page 116) lets
you store the setting for the steering
wheel together with the setting for the
seat position and exterior rear view
mirrors.
Warning!
G
In the case of an accident, liquid electrolyte
may escape the mirror housing if the mirror
glass breaks.
Electrolyte has an irritating effect. Do not al-
low the liquid to come into contact with
eyes, skin, clothing, or respiratory system.
In case it does, immediately flush affected
area with water, and seek medical help if
necessary.
Page 41 of 464
41 Getting started
Driving
The seat belt presenter for driver and pas-
senger makes it easier to put on the seat
belt.
1Seat belt presenter
The seat belt presenter slides out when the
corresponding door is closed and the
SmartKey in the starter switch or
KEYLESS-GO* start/stop button are in
position1 or2.
According to accident statistics, children
are safer when properly restrained in the
rear seating positions than in the front seat-
ing positions. Infants and small children
must ride in back seats and be seated in an
appropriate infant or child restraint system,
which is properly secured with the vehicle's
seat belt or lower anchors, fully in accor-
dance with the child seat manufacturer's
instructions.
A child’s risk of serious or fatal injuries is
significantly increased if the child restraints
are not properly secured in the vehicle and
the child is not properly secured in the child
restraint.Warning!
G
Never let more people ride in the vehicle
than there are seat belts available. Make
sure everyone riding in the vehicle is cor-
rectly restrained with a separate seat belt.
Warning!
G
Never ride in a moving vehicle with the seat
backrest reclined. Sitting in an excessively
reclined position can be dangerous. You
could slide under the seat belt in a collision.
If you slide under it, the belt would apply
force at the abdomen or neck. This could
cause serious or even fatal injuries. The seat
backrest and seat belt provide the best re-
straint when the wearer is in an upright po-
sition and the belt is properly positioned on
the body.Warning!
G
Read and observe the additional warning no-
tices printed in the “Safety and Security”
section (
page 62).
Page 44 of 464
44 Getting startedDrivingAutomatic transmissionGearshift pattern for automatic
transmissionPPark position with gear selector lever
lock
RReverse gear
NNeutral
DDrive position
For more information, see “Automatic
transmission” (
page 157).Starting with the SmartKey
Make sure the gear selector lever is set
toP.
Do not depress accelerator
Turn the SmartKey in the starter switch
to position3 (
page 31) and release it
again immediately ("touch-start").
The engine then starts automatically.
Depress the brake pedal.
The gear selector lever lock is released.
For information on turning off the engine
with the SmartKey, see (
page 54).Starting with KEYLESS-GO*
You can start your vehicle without the
SmartKey in the starter switch using the
KEYLESS-GO start/stop button on the
gear selector lever.
The SmartKey with KEYLESS-GO must be
located in the vehicle.
1KEYLESS-GO start/stop button
Page 45 of 464
45 Getting started
Driving
M a k e s u r e t h e g e a r s e l e c t o r l e v e r i s s e t
toP.
Do not depress accelerator
Depress the brake pedal during the
starting procedure.
The gear selector lever lock is released.
Press KEYLESS-GO start/stop
button1 once.
The engine starts automatically if the
SmartKey with KEYLESS-GO is in the
vehicle.
For information on turning off the engine
with KEYLESS-GO, see “Turning off the en-
gine with KEYLESS-GO*” (
page 55).Starting difficulties
If the engine does not start as described,
carry out the following steps:
If you are starting the engine with the
SmartKey, turn SmartKey in starter
switch to position0 and repeat starting
procedure.
If you are starting the engine with
KEYLESS-GO*: Close any doors that
may be open to allow for better detec-
tion of the SmartKey with
KEYLESS-GO*.
Or:
Start the engine with the SmartKey as
radio signals from another source may
be interfering with the SmartKey with
KEYLESS-GO*.
Repeat the starting procedure
(page 43). Remember that extended
starting attempts can drain the battery.
Get a jump start (
page 388).
If the engine does not start after several
starting attempts, there could be a mal-
function in the engine electronics or in the
fuel supply system.
Notify an authorized Mercedes-Benz
Center.
Page 50 of 464
50 Getting startedDrivingWiping with windshield washer fluid
Push combination switch in the direc-
tion of arrow1 past the resistance
point.
The windshield wipers operate with
washer fluid.
For information on filling up the washer
reservoir, see “Windshield washer system
and headlamp cleaning system*”
(
page 295).
!If anything blocks the windshield wip-
ers (leaves, snow, etc.), switch them off
immediately.
For safety reasons,
turn off the engine by turning
the SmartKey to position 0 and
withdraw SmartKey from starter
switch
or
turn off the engine by pressing
the KEYLESS-GO* start/stop
button and open the driver’s
door (with the driver’s door
open, starter switch is in posi-
tion 0, same as with SmartKey
removed from starter switch)
before attempting to remove any
blockage.
Remove blockage.
Turn the windshield wipers on
again.
If windshield wipers fail to function at
all in switch positionI,
set the combination switch to the
next highest wiper speed
have the windshield wipers
checked at the nearest authorized
Mercedes-Benz Center
Page 52 of 464
52 Getting startedParking and locking
Parking and lockingYou have now completed your first drive.
You have properly stopped and parked
your vehicle. End your drive as follows:Warning!
G
Wait until the vehicle is stationary before re-
moving the SmartKey from the starter
switch. The vehicle cannot be steered when
the SmartKey is removed.Warning!
G
With the engine not running, there is no
power assistance for the brake and steering
systems. In this case, it is important to keep
in mind that a considerably higher degree of
effort is necessary to brake and steer the ve-
hicle.
Warning!
G
Do not park this vehicle in areas where com-
bustible materials such as grass, hay or
leaves can come into contact with the hot
exhaust system, as these materials could be
ignited and cause a vehicle fire.
To reduce the risk of personal injury as a re-
sult of inadvertent vehicle movement, be-
fore turning off the engine and leaving the
vehicle always:
Keep right foot on brake pedal.
Firmly depress parking brake pedal.
Move the gear selector lever to
positionP.
Slowly release brake pedal.
When parked on an incline, turn front
wheel towards the road curb.
Turn the SmartKey to starter switch
position0 and remove, or press
start / stop button (vehicles with
KEYLESS-GO*).
Take the SmartKey or the SmartKey with
KEYLESS-GO* and lock vehicle when
leaving.