brake MERCEDES-BENZ CLS 2014 Owners Manual

Securing the vehicle on slight downhillgradients
XOn light downhill gradients:place
chocks or othersuitableitemsinfront of
the wheelsofthe front and rearaxle.
Raisingthe vehicle
GWARNING
If youdonot positionthe jack correctly at the
appropriate jackingpoint of the vehicle, the
jack could tip over with the vehicle raised.
There isarisk of injury.
Only position the jack at the appropriate
jackingpoint of the vehicle. The base of the
jack must be positioned vertically, directly
under the jackingpoint of the vehicle.
!The jack is designed exclusively for
jackingupthe vehicle at the jackingpoints.
Otherwise, your vehicle could be damaged.
The following must be observed when raising
the vehicle:
Rto raise the vehicle, only use the vehicle-
specific jack that has been tested and
approved by Mercedes-Benz. If used
incorrectly, the jack could tip over with the
vehicle raised.
Rthe jack is designed only to raise and hold
the vehicle forashort time whileawheel
is being changed. It is not suited for
performing maintenancework under the
vehicle.
Ravoid changing the wheel on uphill and
downhill slopes.
Rbefore raising the vehicle, secure it from
rolling away by applying the parking brake
and insertingwheel chocks. Never
disengage the parking brake while the
vehicle is raised.
Rthe jack must be placed onafirm, flat and
non-slip surface. Onaloose surface, a
large, load-bearing underlay must be used.
Onaslippery surface,anon-slip underlay
must be used, e.g. rubber mats.
Rdo not use wooden blocks or similar
objectsasajack underlay.Otherwise, the
jackwill not be able to achieveits load-
bearingcapacity due to the restricted
height.
Rmakesure that the distancebetween the
underside of the tires and the grounddoes
not exceed 1.2in(3cm).
Rnever place your hands and feet under the
raised vehicle.
Rnever lie under the raised vehicle.
Rnever start the engine when the vehicle is
raised.
Rnever open or closeadoor or the trunk lid
when the vehicle is raised.
Rmakesure that no persons are present in
the vehicle when the vehicle is raised.
XUsinglug wrench,loosen the boltson
the wheel you wish to change by about one
full turn. Do not unscrew the bolts
completely.
Changingawheel359
Wheels and tires
Z

XPosition jack$at jacking point.
Example
XMake sure the foot of the jack is directly
beneath the jacking point.
XTurn crank!clockwise until jack$sits
completely on jacking pointand the
base of the jack lies evenly on the ground.
XTurn crank!until the tire is raised a
maximum of 1.2 in (3 cm) off the ground.
Removingawheel
!AMG vehicles:during removaland
repositioning of the wheel, the wheel rim
can strike the ceramic-brake disc and
damage it. Therefore, take precautions and
getasecond persontoassist you.
Alternatively, you can useasecond
alignment bolt.
!Do not place wheel bolts in sand or on a
dirty surface. The bolt and wheel hub
threads could otherwise be damaged when
you screw them in.
XUnscrew the uppermost wheel bolt
completely.
XScrew alignment boltinto the thread
instead of the wheel bolt.
XUnscrew the remaining wheel bolts fully.
XRemove the wheel.
Mountinganew wheel
GWARNING
Oiled or greased wheel boltsordamaged
wheel bolts/hub threads can cause thewheel
boltstocomeloose.Asaresult, you could
loseawheel while driving. There isarisk of
accident.
Never oil or grease wheel bolts. In the event
of damage to the threads, contactaqualified
specialist workshop immediately.Have the
damagedwheel boltsorhub threads
replaced/renewed. Do notcontinue driving.
360Changingawheel
Wheels and tires

GWARNING
If you tighten the wheelbolts or wheelnuts
when the vehicleisraised, the jack couldtip
over. There isarisk of injury.
Only tighten the wheelbolts or wheelnuts
when the vehicleisonthe ground.
Always pay attention to the instructions and
safety notes in the "Changingawheel"
section (Ypage357).
Only use wheelbolts that have been designed
for the wheeland the vehicle. For safety
reasons, Mercedes-Benz recommends that
you only use wheelbolts which have been
approved for Mercedes-Benz vehicles and the
respective wheel.
!AMG vehicle with ceramic brake
discs:during removaland repositioning of
the wheel, the wheelrim can strike the
ceramic-brake disc and damage it.
Therefore, take precautions and have a
second personassist you. Alternatively,
you can useasecond alignment bolt.
!To prevent damage to the paintwork, hold
the wheel securely against the wheel hub
while screwing in the first wheel bolt.
Positioningawheel (example: vehicle with anemergency spare wheel)
XCleanthe wheel and wheel hub contact
surfaces.
XSlide the wheel to be mounted onto the
alignment bolt and push it on.
XTighten the wheel bolts until they are
finger-tight.
XUnscrew the alignment bolt.
XTighten the last wheel bolt until it is finger-
tight.
XVehicles withacollapsible spare
wheel:inflate thecollapsible spare wheel
(Ypage 368).
Only then lower thevehicle.
Lowering thevehicle
GWARNING
The wheels could work loose if thewheel nuts
and boltsare not tightenedtothe specified
tightening torque. There isarisk of accident.
Have the tightening torque immediately
checked ataqualified specialist workshop
afterawheel is changed.
!Vehicles withacollapsible spare
wheel:before lowering thevehicle, inflate
thecollapsible spare wheel with thetire
inflationcompressor. The wheel rim could
otherwise be damaged.
Tighteningthe wheel nuts (example: vehicle withan emergencyspare wheel)
XTurn the crank of the jack counter-
clockwise until the vehicle is once again
standingfirmly on the ground.
XPlace the jack to one side.
XTighten the wheel bolts evenly in a
crosswise pattern in the sequence
indicated (to). The specified
tightening torque is96 lb-ft(130 Nm).
XTurn the jack back to its initial position.
Changingawheel361
Wheels and tires
Z

Example: vehicleidentification plate (Canada only)
VIN
$Paint code
iThe data shown on the vehicle
identificationplate is used only as an
example. This data is differentfor every
vehicle and can deviate from the data
shown here. You can find the data
applicabletoyour vehicle on the vehicle
identification plate.
VIN
XSlide the right-hand front seat to its
rearmost position.
XFold floor coveringupwards.
You will see VIN.
The VIN can also be found in the following
locations:
Ron the lower edge of the windshield
(Ypage 373)
Ron the vehicle identification plate
(Ypage 372)
Engine number
Emission control information plate,
including the certification of both federal
and Californian emissions standards
Engine number (stamped into the
crankcase)
$VIN (on the lower edge of the windshield)
Service products and filling
capacities
Important safety notes
GWARNING
Serviceproducts may be poisonous and
hazardous to health. There isarisk of injury.
Comply with instructions on the use, storage
and disposal of service products on the labels
of the respective original containers. Always
store service products sealed in their original
containers. Always keep service products out
of the reach of children.
HEnvironmental note
Dispose of service products in an
environmentally responsible manner.
Serviceproducts include the following:
RFuels
RLubricants (e.g. engine oil, transmission oil)
RCoolant
RBrake fluid
RWindshield washer fluid
RClimate control system refrigerant
Service products and filling capacities373
Technical data
Z

The engine oils are matched to the
performance of Mercedes-Benz engines and
service intervals. You should therefore only
use engine oils and oil filters that are
approved for vehicles with maintenance
systems.
Foralist of approved engine oils and oil filters,
consult an authorized Mercedes-Benz
Center. Or visit the website
http://bevo.mercedes-benz.com.
The table shows which engine oils have been
approved for your vehicle.
ModelEngine
model
MB
Approval
CLS 550
CLS 550 4MATIC
278229.5
CLS 63 AMG
CLS 63 AMG
4MATIC
157229.5
Use only SAE 0W-40orSAE 5W-40 engine oils
for AMG vehicles.
iMB approval is indicated on the oil
containers.
Fillingcapacities
The following values refer to an oil change
including the oil filter.
ModelCapacity
All models (except
for AMG vehicles)
8.5 US qt (8.0 l)
All models (AMG
vehicles)
With external oil
cooler: 9.0 US qt
(8.5 l)
Additives
!Do not use any additives in the engine oil.
This coulddamage the engine.
Engine oil viscosity
Viscosity describes the flow characteristics
ofafluid. If an engine oil hasahigh viscosity,
this means that it is thick;alow viscosity
means that it is thin.
Select an engine oil with an SAE classification
(viscosity) suitable for the prevailing outside
temperatures. The table showsyou which
SAE classifications are to be used. The low-
temperature characteristics of engine oils
can deteriorate significantly, e.g. asaresult
of aging, soot and fuel deposits. It is therefore
strongly recommendedthat you carry out
regular oil changes using an approved engine
oil with the appropriate SAE classification.
Brake fluid
GWARNING
The brake fluidconstantly absorbs moisture
from the air. This lowers the boiling point of
the brake fluid. If the boiling point of the brake
fluidistoo low,vaporpocketsmay form in the
brake system when the brakes are applied
hard. This would impair braking efficiency.
There isarisk of an accident.
You should have the brake fluid renewed at
the specified intervals.
Comply with the important safety notes for
service products when handling brake fluid
(Ypage 373).
The brake fluid change intervals can be found
in the Maintenance Booklet.
376Service products and filling capacities
Technical data

Only use brake fluid approved by Mercedes-
Benz according to MB Approval 331.0.
Information aboutapproved brake fluid can
be obtainedatany qualified specialist
workshop or on the Internet at
http://bevo.mercedes-benz.com.
iHave the brake fluid regularly replaced at
aqualified specialist workshop and the
replacementconfirmed in the Maintenance
Booklet.
Coolant
Important safety notes
GWARNING
If antifreezecomes into contact with hot
components in the engine compartment, it
may ignite. There isarisk of fire and injury.
Let the engine cool down before you add
antifreeze. Make sure that antifreezeisnot
spilled next to the filler neck.Thoroughly
clean the antifreeze from components before
startingthe engine.
!Only add coolant that has been premixed
with the desired antifreezeprotection. You
couldotherwise damage the engine.
Further information on coolants can be
found in the Mercedes-Benz Specifications
for Service Products, MB Specifications for
Service Products 310.1, e.g. on the
Internet at
http://bevo.mercedes-benz.com.Or
contactaqualified specialist workshop.
!Always useasuitable coolant mixture,
even in countries where high temperatures
prevail.
Otherwise, the engine cooling system is not
sufficiently protected from corrosionand
overheating.
Comply with the important safety precautions
for service products when handling coolant
(Ypage373).
The coolant isamixture of water and
antifreeze/corrosion inhibitor. It performs
the following tasks:
Rcorrosionprotection
Rantifreeze protection
Rraising the boiling point
If the coolant has antifreeze protection down
to -35‡(-37†),the boiling point of the
coolant during operationisapproximately
266‡(130 †).
The antifreeze/corrosion inhibitor
concentration in the engine cooling system
should:
Rbe at least 50%. This will protect the engine
cooling system against freezing down to
approximately -35‡(-37 †).
Rnot exceed 55% (antifreeze protection
down to -49‡[-45 †]). Otherwise, heat
will not be dissipated as effectively.
If the vehicle has lost coolant, add equal
amounts of water and antifreeze/corrosion
inhibitor.
Mercedes-Benz recommends an antifreeze/
corrosion inhibitor concentrate in
accordance with MB Specifications for
Service Products 310.1.
The coolant is checked with every
maintenance interval ataqualified specialist
workshop.
iWhen the vehicle is first delivered, it is
filled withacoolant mixture that ensures
adequate antifreeze and corrosion
protection.
Filling capacities
ModelCapacity
All models (except
for AMG vehicles)
Approx. 13.0 US qt
(12.3 l)
All models (AMG
vehicles)
Approx. 11.5 US qt
(10.9 l)
iUse MB 325.0 or MB 326.0 corrosion
inhibitor/antifreeze.
Service products and filling capacities377
Technical data
Z