ignition MERCEDES-BENZ CLS 2014 Owners Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2014, Model line: CLS, Model: MERCEDES-BENZ CLS 2014Pages: 382, PDF Size: 4.7 MB
Page 331 of 382
It is better to have the vehicle transported
than to have it towed.
If the vehicle has suffered transmission
damage, have it transported onatransporter
or trailer.
The automatic transmission must be in
positionNwhen the vehicle is being towed.
The battery must be connected and charged.
Otherwise,you:
Rcannot turn the SmartKey to position2in
the ignition lock
Rcannot shift the automatic transmission to
positionN
iDeactivate the automatic locking feature
(Ypage 83). You could otherwisebelocked
out when pushing or towing the vehicle.
Installing/removing the towing eye
Installing the towing eye
GWARNING
The exhaust tail pipe may be very hot. There
isarisk of burns when removing the rear
cover.
Do not touch the exhaust pipe.Take particular
carewhen removingtherear cover.
Example:towing eye covers
Towing eye covers (AMG vehicles)
The mountings for the removable towing eyes
are located in the bumpers. They are at the
front and at the rear, behind the covers.
XRemove the towing eye from the vehicle
tool kit (Ypage 320).
XPull cover out of the bumper in the
direction of the arrow by inserting your
fingers into the recess.
XPress the mark on cover inwards in the
direction of the arrow.
Towing and tow-starting329
Breakdown assistance
Z
Page 332 of 382
XTake cover off the opening.
XScrew in and tighten the towing eye
clockwise to the stop.
Removing the towing eye
XUnscrew and remove the towing eye.
XPosition the top of cover in the bumper
and press it in at the bottom until it
engages.
XAttach cover to the bumper and press
until it engages.
XPlace the towing eye in the vehicle tool kit.
Towing the vehicle with the rear axle
raised
!The ignition must be switched off if you
are towing the vehicle with the rear axle
raised. Intervention by ESP®could
otherwise damage the brake system.
Only possible for vehicles without
4MATIC.
XSwitchonthe hazard warning lamps
(Ypage 120).
XTurn the SmartKey to position0in the
ignition lock and remove the SmartKey
from the ignition lock.
XWhen leaving the vehicle, take the
SmartKey or the KEYLESS-GO key with you.
When towing your vehicle with the rear axle
raised, it is importantthat you observe the
safety instructions (Ypage 328).
Towingavehicle with both axles on
theground
It is importantthat you observe the safety
instructions when towing away your vehicle
(Ypage 328).
The automatic transmission automatically
shifts to positionPwhen you open the driver's
or front-passenger door or when you remove
the SmartKey from the ignition lock. In order
to ensure that the automatic transmission
stays in positionNwhen towing the vehicle,
you must observe the following points:
XMake sure that the vehicle is stationary and
the SmartKey in the ignition lock is in
position0.
XTurn the SmartKey to position2in the
ignition lock.
On vehicles with KEYLESS-GO, use the
SmartKey instead of the Start/Stop button
(Ypage 147).
XDepress and hold the brake pedal.
XShift the automatic transmission to
positionN.
XRelease the brake pedal.
XRelease the parking brake.
XSwitch on the hazard warning lamps
(Ypage 120).
XLeave the SmartKey in position2in the
ignition lock.
iWhen towing with the hazard warning
lamps switched on, use the combination
switch as usualtosignalachange of
direction. In this case, only the indicator
lamps for the direction of travel flash. After
resetting the combination switch, the
hazard warning lamp starts flashing again.
Transporting the vehicle
!Only lash the vehicle down by the wheels
or wheel rims, not by parts of the vehicle
such as axle or steering components.
Otherwise, the vehicle could be damaged.
The towing eye can be used to pull the vehicle
ontoatrailer or transporter for transporting
purposes.
330Towing and tow-starting
Breakdown assistance
Page 333 of 382
XTurn the SmartKey to position2in the
ignition lock.
XShift the automatic transmission to
positionN.
As soon as the vehicle is loaded:
XPrevent the vehicle from rolling away by
applying the parking brake.
XShift the automatic transmission to
positionP.
XTurn the SmartKey to position0in the
ignition lock and remove the SmartKey
from the ignition lock.
XSecure the vehicle.
Notes on 4MATIC vehicles
!Vehicles with 4MATICmust not be towed
with either the frontorthe rear axle raised,
as doing so will damage the transmission.
If the vehicle has transmission damage or
damage to the front or rear axle, have it
transported onatransporter or trailer.
In the event of damage to the electrical
system
If the battery is defective, the automatic
transmission will be locked in positionP.To
shift the automatic transmission to position
N,you must provide power to the vehicle's
electrical system in the same way as when
jump-starting (Ypage 326).
Have the vehicle transported onatransporter
or trailer.
Tow-starting (emergency engine
starting)
!Vehicles with automatic transmission
must not be started by tow-starting. This
could otherwise damage the transmission.
You can find information on "Jump-starting"
at (Ypage 326).
Fuses
Important safety notes
GWARNING
If you manipulate or bridgeafaulty fuse or if
you replace it withafuse withahigher
amperage, the electric cables could be
overloaded. This could result inafire. There
isarisk of an accident and injury.
Always replace faulty fuses with the specified
new fuses having the correct amperage.
!Only use fuses that have been approved
for Mercedes-Benzvehicles and which
have the correct fuse ratingfor the system
concerned. Otherwise, componentsor
systems could be damaged.
The fuses in your vehicle serve to close down
faulty circuits. Ifafuse blows,all the
componentsonthecircuit and their functions
stop operating.
Blown fusesmust be replacedwith fuses of
the same rating, which you can recognize by
the color and value. The fuse ratings are listed
in the fuse allocation chart.
Ifanewly inserted fuse also blows, have the
cause traced and rectified ataqualified
specialist workshop, e.g. an authorized
Mercedes-BenzCenter.
Beforechangingafuse
XSecure the vehicle against rolling away
(Ypage 167).
XSwitchoff all electrical consumers.
XTurn the SmartKey to position0in the
ignition lock and remove it (Ypage 147).
or
XOn vehicles with KEYLESS-GO, make sure
the ignition is switched off (Ypage 147).
All indicator lamps in the instrument cluster
must be off.
Fuses331
Breakdown assistance
Z
Page 334 of 382
The fuses are located in various fuse boxes:
RFuse box in the engine compartment on the
left-hand side of the vehicle, when viewed
in the direction of travel
Rfuse box in the trunk on the right-hand side,
when viewed in the direction of travel
the fuse allocation chart is located in the
vehicle tool kit in the stowage compartment
under the trunk floor (Ypage 320).
Fuse box in the engine compartment
GWARNING
When the hood is open and the windshield
wipers are set in motion,you can be injured
by the wiper linkage. There isarisk of injury.
Always switch off the windshield wipers and
the ignition before opening the hood.
!Make sure that no moisture can enter the
fuse box when the cover is open.
!When closing the cover, make sure that it
is lying correctly on the fuse box. Moisture
seeping in or dirt could otherwise impair
the operation of the fuses.
XMake sure that the windshield wipers are
turned off.
XOpen the hood.
XUseadry cloth to remove any moisture
from the fuse box.
XTo open:remove lines from the guides.
XMove lines aside. Route the lines behind
connection $to do this.
XOpen clamp .
XRemove the fuse box cover forwards.
XTo close:check whether the rubber seal is
lying correctly in the cover.
XInsert the cover at the rear of the fuse box
into the retainer.
XFold down cover and close clamps .
XSecure lines in the guides.
XClose the hood.
Fuse box in the trunk
!Make sure that no moisture can enter the
fuse box when the cover is open.
!When closing the cover, make sure that it
is lying correctly on the fuse box. Moisture
seeping in or dirt could otherwise impair
the operation of the fuses.
XOpen the trunk lid.
XTo open:release cover at the top right
and left-hand sides withaflat object.
XOpen cover downwards in the direction
of the arrow.
332Fuses
Breakdown assistance
Page 344 of 382
Ryou adoptaverysporty driving style
(cornering at high speeds or driving with
high rates of acceleration).
Ryou are driving withaheavy load(in the
vehicleoronthe roof).
Restarting the tire pressure loss
warningsystem
Restart the tire pressure loss warning system
if you have:
Rchanged the tire pressure
Rchanged the wheels or tires
Rmounted new wheels or tires
XBefore restarting, make sure that the tire
pressures are set properly on all four tires
for the respective operating conditions.
The recommendedtire pressures can be
found on the Tire and Loading Information
placard on the B-pillar on the driver's side
or the tire pressure table on the fuel filler
flap.The tire pressure loss warning system
can only give reliablewarnings if you have
set the correct tire pressure. If an incorrect
tire pressure is set, these incorrectvalues
will be monitored.
XAlsoobservethenotesinthesectionontire
pressures (Ypage 338).
XMake sure that the SmartKey is in position
2in the ignition lock (Ypage 147).
XPress the \nor button on the
steeringwheel to selecttheServ.menu.
XPress the or button on the
steering wheel to select theTire
Pressuremenu.
XPress the button.
TheRun Flat Indicator Active
Press 'OK' to Restartmessage
appears in the multifunction display.
If you wish to confirm the restart:
XPress the button.
TheTire Pressure Now OK?message
appears in the multifunction display.
XPress the or button to select
Yes.
XPress the button.
TheRun Flat Indicator Restarted
message appears in the multifunction
display.
Afterateach-in period, the tire pressure
loss warning system will monitor the set
tire pressures of all four tires.
If you wish to cancel the restart:
XPress the button.
or
XWhen theTire Pressure Now OK?
message appears, press the
or button to selectCancel.
XPress the button.
The tire pressure values stored at the last
restart will continue to be monitored.
Tire pressuremonitor
General notes
Ifatire pressure monitor is installed, the
vehicle's wheels have sensors that monitor
the tire pressures in all four tires. The tire
pressure monitor warns you if the pressure
drops in one or more of the tires. The tire
pressure monitor only functions if the correct
sensors are installed on all wheels.
Information on tire pressures is displayed in
the multifunction display. Afterafew minutes
of driving, the current tire pressure of each
tire is shown in theServicemenu of the
multifunction display. For further information
on displaying this message, refer to the
"Checking the tire pressure electronically"
section (Ypage 344).
342Check
Wheels and tires
Page 346 of 382
The tire pressure monitor hasayellow
warning lamp in the instrument cluster for
indicatingapressure loss or malfunction.
Whether the warning lamp flashes or lights up
indicates whetheratire pressure is too low or
the tire pressure monitor is malfunctioning:
Rif the warning lamp is lit continuously, the
tire pressure on one or more tires is
significantly too low. The tire pressure
monitor is not malfunctioning.
Rif the warning lamp flashes for around a
minute and then remains lit constantly, the
tire pressure monitor is malfunctioning.
If the tire pressure monitor is malfunctioning,
it may take more than ten minutes for the tire
pressure warning lamp to inform you of the
malfunction by flashing for approximately one
minute and then remaining lit. When the
malfunction has been rectified, the tire
pressure warning lamp goes out afterafew
minutes of driving.
The tire pressure values indicated by the on-
board computer may differ from those
measured atagas station withapressure
gauge. The tire pressures shown by the on-
board computer refer to those measured at
sea level. At high altitudes, the tire pressure
values indicated byapressure gauge are
higher than those shown by the on-board
computer.Inthis case, do not reduce the tire
pressures.
The operation of the tire pressure monitor can
be affected by interference from radio
transmitting equipment (e.g. radio
headphones, two-way radios) that may be
being operated in or near the vehicle.
Checking the tire pressure
electronically
XMake sure that the SmartKey is in position
2(Ypage 147) in the ignition lock .
XPress the \nor button on the
steering wheel to select theServ.menu.
XPress the or button to select
Tire Pressure.
XPress the button.
The current tire pressure of each tire is
shown in the multifunction display.
If the vehicle was parked for longer than
20 minutes,theTirepressureswillbe
displayed after drivingafew
minutesmessage is shown.
Afterateach-in process, the tire pressure
monitor automatically detects new wheels or
new sensors. As long asaclear allocation of
the tire pressure value to the individual
wheels is not possible, theTire Pressure
Monitor Activedisplaymessage is shown
instead of the tire pressure display. The tire
pressures are already being monitored.
iIf an emergency spare wheel is mounted,
the system may continue to show the tire
pressure of the wheel that has been
removed forafew minutes. If this occurs,
note that the value displayed for the
position where the spare wheel is mounted
is not the same as the current tire pressure
of the emergency spare wheel.
Tire pressuremonitor warning
messages
If the tire pressure monitor detectsapressure
loss in one or more tires,awarning message
is shown in the multifunction displayand the
yellow tire pressure monitor warning lamp
comes on.
RIf theCorrect Tire Pressuremessage
appears in the multifunction display, the
tire pressure in at least one tire is too low
and must be corrected at the next
opportunity.
RIf theCheck Tire Pressuremessage
appears in the multifunction display, the
tire pressure in one or more tires has
dropped significantly and the tires must be
checked.
RIf theTire Malfunctionappears in the
multifunction display, the tire pressure in
344Check
Wheels and tires
Page 347 of 382
one or more tires has dropped suddenly
and the tires must be checked.
Observe the instructions and safety notes in
the display messages in the "Tires" section
(Ypage 258).
iIf the wheel positions on the vehicle are
rotated, the tire pressures may be
displayed for the wrong positions for a
short time. This is rectified afterafew
minutes of driving, and the tire pressures
are displayed for the correctpositions.
Restarting the tire pressuremonitor
When you restart the tire pressure monitor,
all existingwarning messages are deleted and
the warning lamps go out. The monitor uses
the currently set tire pressures as the
reference values for monitoring. In most
cases, the tire pressure monitor will
automatically detect the new reference
values after you have changed the tire
pressure. However, you can also define
reference values manually as described here.
The tire pressure monitor then monitors the
new tire pressure values.
XSet the tire pressure to the value
recommended for the corresponding
driving situation on the Tire and Loading
Information placard on the B-pillar on the
driver's side (Ypage 338).
Additional tire pressure values for different
loads can also be found on the tire pressure
table on the inside of the fuel filler flap
(Ypage 338).
XMake sure that the tire pressure is correct
on all four wheels.
XMake sure that the SmartKey is in position
2in the ignition lock.
XPress the \nor button on the
steeringwheel to select theServ.menu.
XPress the or button to select
Tire Pressure.
XPress the button.
The multifunction display shows the
current tire pressure for each tire or the
Tire pressures will be displayed
after drivingafew minutes
message.
XPress the button.
The multifunction display shows theUse
CurrentPressuresasNewReference
Valuesmessage.
If you wish to confirm the restart:
XPress the button.
TheTire Press. Monitor Restarted
message appears in the multifunction
display.
After driving forafew minutes, the system
checkswhether the current tire pressures
are within the specified range. The new tire
pressures are then accepted as reference
values and monitored.
If you wish to cancel the restart:
XPress the button.
The tire pressure values stored at the last
restart will continue to be monitored.
Loading the vehicle
Instruction labels for tires and loads
GWARNING
Overloaded tires can overheat, causing a
blowout. Overloaded tires can also impair the
steering and driving characteristics and lead
to brake failure. There isarisk of accident.
Observe the load rating of the tires. The load
rating must be at least half of the GAWR of
your vehicle. Never overload the tires by
exceeding the maximum load.
Two instruction labels on your vehicle show
the maximum possible load.
(1) The Tire and Loading Information placard
is on the B-pillar on the driver's side. The
Tire and Loading Information placard
shows the maximum permissible number
of occupantsand the maximum
permissible vehicle load. It also contains
Loading the vehicle345
Wheels and tires
Z
Page 360 of 382
to the tiresorchassiscomponents.
Components damagedinthiswaymayfail
unexpectedly.There isarisk of an accident.
Do not use power washers with circular jet
nozzles to clean the vehicle. Have damaged
tires or chassis components replaced
immediately.
Mountingawheel
Preparing the vehicle
XStop the vehicle on solid, non-slippery and
levelground.
XApply the parking brake.
XBring the front wheels into the straight-
ahead position.
XShift the transmission to positionP.
XVehicles with AIRMATIC:make sure that
"normal" levelisselected(Ypage 189).
XSwitch off theengine.
XVehicles without KEYLESS-GO:remove
theSmartKey from theignition lock.
XVehicles with KEYLESS-GO:open the
driver'sdoor.
The on-board electronics nowhave status
0.This is the same as the SmartKey having
been removed.
XVehicles with KEYLESS-GO:remove the
Start/Stop button from the ignition lock
(Ypage 147).
XIf included in the vehicle equipment,
remove the tire-change tool kit from the
vehicle (Ypage 320).
XSecure the vehicle to prevent it from rolling
away.
Securing the vehicle to prevent it from
rolling away
If your vehicle is equipped withawheel chock,
it can be found in the tire-change tool kit
(Ypage 320).
The folding wheel chock is an additional
safety measure to prevent the vehicle from
rolling away,for example when changing a
wheel.
XFold both plates upwards .
XFold out lower plate .
XGuidethe lugs on the lower plate fully into
the openings in base plate $.
Securing the vehicle on level ground
XOn level ground:place chocksorother
suitable items under the front and rear of
the wheel that is diagonallyopposite the
wheel you wish to change.
358Changingawheel
Wheels and tires
Page 371 of 382
!Do not operate the tire inflation
compressor for longer than eight minutes
atatime withoutabreak. It may otherwise
overheat.
The tire inflation compressor can be
operated againonce it hascooleddown.
XMount the collapsiblespare wheelas
described (Ypage 357).
The collapsible spare wheel must be
mounted before it is inflated.
XPull connector !and the air hose out of
the housing.
XRemove the cap from the valve on the
collapsible spare wheel.
XScrew union nut on the air hose ontothe
valve.
XMake sure on/off switch of the tire
inflation compressor is set to0.
XInsert connector !intothe cigarette
lighter socket or intoa12Vsocket in your
vehicle.
Observe the notes on the cigarettelighter
(Ypage 288). Observe the notes on
sockets(Ypage 289).
XTurn the SmartKey to position1in the
ignition lock (Ypage 147).
XPress on/offswitch on thetireinflation
compressor toI.
The tireinflationcompressor is switched
on. The tire is inflated. The tire pressure is
shown on pressure gauge $.
XInflate the tire to the specified tire
pressure.
The specified tire pressure is printed on the
yellow label of the emergencyspare wheel.
XWhen the specified tire pressure has been
reached, press on/offswitch on the
electric air pump to0.
The tireinflationcompressor is switched
off.
XTurn the SmartKey to position0in the
ignition lock.
XIf the tire pressure is higher than the
specified pressure, press pressure release
button until the correcttire pressure has
been reached.
XUnscrew union nut on the air hose from
the valve.
XScrew the valve cap ontothe collapsible
spare wheel valve again.
XStow plug !and the air hose in the lower
section of the blower housing.
XStow the tire inflation compressor in the
vehicle.
Emergency sparewheel369
Wheels and tires
Z
Page 376 of 382
Comply withall valid regulationswithrespect
to handling, storing,and disposingofservice
fluids.
Components and serviceproductsmust be
matched. You should thereforeonly use
products thathave been tested and approved
by Mercedes-Benz.
Information on tested and approved products
can be obtainedatanauthorized Mercedes-
BenzCenterorontheInternet at
http://bevo.mercedes-benz.com.
You can recognize service products approved
by Mercedes-Benzbythefollowing
inscription on thecontainers:
RMB-Freigabe (e.g. MB-Freigabe 229.51)
RMB Approval (e.g. MB Approval 229.51)
Other designationsorrecommendations
indicatealevel of qualityoraspecification in
accordance withanMBSheet number (e.g.
MB 229.5). Theyhave notnecessarily been
approved by Mercedes-Benz.
Fuel
Important safetynotes
GWARNING
Fuel is highly flammable. If you handle fuel
incorrectly, there isarisk of fire and
explosion.
You must avoid fire, open flames, creating
sparks and smoking. Switchoff the engine
and, if applicable, the auxiliary heating before
refueling.
GWARNING
Fuel is poisonous and hazardous to health.
There isarisk of injury.
You must make sure that fuel does not come
into contact with your skin,eyes or clothing
and that it is not swallowed. Do not inhale fuel
vapors. Keep fuel away from children.
If you or otherscome into contact with fuel,
observe the following:
RWash away fuel from skin immediately
using soap and water.
RIf fuel comes into contact with your eyes,
immediately rinse them thoroughly with
clean water. Seek medical assistance
without delay.
RIf fuel is swallowed, seek medical
assistancewithout delay. Do not induce
vomiting.
RImmediately change out of clothing which
has come into contact with fuel.
Tank capacity
ModelTotal
capacity
All models21.1USgal
(80.0l)
ModelOf which
reserve
All models (except for
AMG vehicles)
Approx.
2.4 US qt
(9.0 l)
All models (AMG vehicles)Approx.
3.7 US gal
(14.0l)
Gasoline
Fuel grade
!Do not use diesel to refuel vehicles with a
gasoline engine. Do not switch on the
ignition if you accidentally refuel with the
wrong fuel. Otherwise, the fuel will enter
the fuel system. Even small amounts of the
wrong fuel could result in damage to the
fuel system and the engine. Notifya
qualified specialist workshopand have the
fuel tank and fuel lines drained completely.
374Service products and filling capacities
Technical data