light MERCEDES-BENZ CLS 2014 Owners Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2014, Model line: CLS, Model: MERCEDES-BENZ CLS 2014Pages: 382, PDF Size: 4.7 MB
Page 291 of 382
AMG vehicles
Your attention must always be focused on the
traffic conditions. Only usethe cigarette
lighterwhen road and traffic conditions
permit.
XTurn the SmartKey to position2in the
ignition lock (Ypage 147).
XTo open:briefly press the trim on
cover .
The stowage compartmentopens.
XPress in cigarette lighter .
Cigarettelighter will pop out
automatically when the heatingelementis
red-hot.
12Vsockets
General notes
XTurn theSmartKey to position1in the
ignitionlock (Ypage 147).
The socketscan be used for accessories with
amaximum draw of 180W(15 A).
Accessories include such items as lamps or
chargers for mobile phones.
If you use the socketsfor long periods when
the engine is switched off, the battery may
discharge.
iAn emergencycut-out ensures that the
on-board voltage does not drop too low. If
the on-board voltage is too low, the power
to the socketsisautomatically cut. This
ensures that there is sufficient power to
start the engine.
Socket under the armrest
XOpen the stowage compartment under the
armrest (Ypage 280).
XLift up the cover of socket .
Socket in the front-compartment center
console
All vehicles (except AMG)
XTo open:slide cover forwards until it
engages.
XLift up the cover of socket .
XTo close:briefly press cover at the
front.
The cover moves back.
Features289
Stowage and features
Z
Page 293 of 382
Raservicesubscription is available
Rthestarter battery is sufficiently charged
iDetermining thelocationofthe vehicle on
amap is only possible if:
RGPS reception is available.
Rthe vehicle position can be forwarded to
the Customer AssistanceCenter.
The mbrace system
To adjust the volume duringacall, proceed
as follows:
XPress the or button on the
multifunction steering wheel.
or
XUse the volume controller of the audio
system/COMAND.
The system offers various services, e.g:
RAutomatic and manual emergency call
RRoadside Assistancecall
RMB Info call
USA only: you can find information and a
description of all available features under
"Owners Online" at http://www.mbusa.com.
System self-test
After you have switched on the ignition, the
system carries outaself-diagnosis.
Amalfunction in thesystem has been
detected if oneofthefollowingoccurs:
RThe indicator lamp in theSOS button does
notcomeonduringthesystem self-test.
RThe indicator lamp in the Roadside
Assistancebuttondoes not light up during
self-diagnosis of the system.
RThe indicator lamp in the MB Info call
button does not light up during self-
diagnosis of the system.
RThe indicator lamp in one or more of the
following buttonscontinues to light up red
after the system self-diagnosis:
-SOS button
- Roadside Assistance call button
- MB Info call button
Rafter the system self-diagnosis, the
InoperativeorService Not
Activatedmessage appears in the
multifunction display.
Ifamalfunction is indicated as outlined
above, the system may not operate as
expected. In the event of an emergency, help
will have to be summoned by other means.
Have the system checked at the nearest
authorized Mercedes-Benz Center or contact
the following service hotlines:
RUSA:Mercedes-Benz Customer Assistance
Center at
1-800-FOR-MERCedes (1-800-367-6372)
or 1-866-990-9007
RCanada:Customer Serviceat
1-888-923-8367
Emergency call
Important safety notes
!You must havealicense agreement to
activate the mbrace service. Make sure
that your system is activated and ready for
use. To register, press the MB Info call
button.Ifany of the steps mentioned are
not carried out, the system may not be
activated.
If you have questions about the activation,
contact one of the following telephone
hotlines:
RUSA:Mercedes-Benz Customer
Assistance Center at
1-800-FOR-MERCedes
(1-800-367-6372)or1-866-990-9007
RCanada:Customer Serviceat
1-888-923-8367
Features291
Stowage and features
Z
Page 301 of 382
Triggeringthe vehicle alarm
With thisfunction, youcan triggerthe
vehicle's panic alarm via text message. An
alarm sounds and the exterior lighting
flashes. Depending on the setting, the panic
alarm lasts five or ten seconds. Afterwards,
the alarm switches off.
Garage door opener
Important safety notes
GWARNING
When you operate or program the garage door
with the integrated garage door opener,
persons in the range of movement of the
garage door can become trapped or struck by
the garage door. There isarisk of injury.
When using the integrated garage door
opener, always make sure that nobody is
within the rangeofmovementofthe garage
door.
GWARNING
Combustion engines emit poisonous exhaust
gases such as carbonmonoxide. Inhaling
these exhaust gases leads to poisoning. There
isarisk of fatal injury. Therefore never leave
the engine runninginenclosed spaces
without sufficient ventilation.
The HomeLink®garage door opener
integrated in the rear-view mirror allows you
to operate up to three different door and gate
systems.
Use the integrated garage door opener only
on garage doors that:
Rhave safety stop and reverse features and
Rmeet current U.S. federal safety standards
When programmingagarage door opener,
park the vehicle outside the garage.
iCertain garage door drives are
incompatible with the integrated garage
door opener. If you have difficulty
programming the integrated garage door
opener, contact an authorized Mercedes-
Benz Center.
Alternatively, you can call the following
telephone assistance services:
RUSA:Mercedes-Benz Customer
Assistance Center at
1-800-FOR-MERCedes
RCanada:Customer Serviceat
1-800-387-0100
RHomeLink®hotline 1-800-355-3515
(free of charge)
More information on HomeLink®and/or
compatible products is also available
online at http://www.homelink.com.
iNotes on the declaration of conformity
(Ypage 25).
USA:FCC ID: CB2HMIHL4
Canada: IC: 279B-HMIHL4
Programming
Programming buttons
Observe the "Important safety notes"
(Ypage 299).
Integrated garage door opener in the rear-viewmirror
Garage door remote control is not part of
the integrated garage door opener.
XThe first time before programming, clear
the integrated garage door opener memory
(Ypage 301).
XTurn the SmartKey to position2in the
ignition lock.
Features299
Stowage and features
Z
Page 302 of 382
XPress and hold one of buttons to !on
the integrated garage door opener.
Afterashort time, indicator lamp lights
up yellow.
iIndicator lamp lights up yellow as soon
as button , $or !is programmed for
the first time. If the selected button has
already been programmed, indicator
lamp will only light up yellow after ten
seconds have elapsed.
XRelease button , $or !.Indicator
lamp flashes yellow.
XPoint garage door remotecontrol
towards buttons to !on the rear-view
mirror atadistanceof2to8inches (5 to
20 cm).
iThe required distancebetween remote
control and the integrated garage door
opener depends on the garage door drive
system. Several attempts might be
necessary. You should test every position
for at least 25 seconds before trying
another position.
XPress and hold button %on remotecontrol
until indicator lamp lights up green.
If indicator lamp lights up green or
flashes, then programming has been
successful.
XRelease button %on remote control for
the garage door drive system.
XIf indicator lamp lights up red: repeat
the programming procedure for the
corresponding button on the rear-view
mirror. When doing so, vary the distance
between remote control and the rear-
view mirror.
iIf the indicator lamp flashes green after
successful programming, the garage door
system is usingarolling code. After
programming, you must synchronize the
garage door opener integrated in the rear-
view mirror with the receiver of the garage
door system.
Synchronizing the rolling code
Observe the "Important safety notes"
(Ypage 299).
Your vehicle must be within reach of the
garage door or exterior gate drive. Make sure
that neither your vehicle nor any persons/
objectsare present within the sweep of the
door or gate.
XTurn the SmartKey to position2in the
ignition lock.
XPress the program button of the door or
gate drive (see the door or gate drive
operating instructions, e.g. under
"programming of additional remote
controls").
iUsually,you now have 30seconds to
initiate the next step.
XPress previously programmed button ,
$or !of the integrated garage door
opener until the door closes.
The rolling code synchronization is then
complete.
Notes on programming the remote
control
Canadianradio frequency laws require a
"break"(or interruption)ofthetransmission
signals after broadcastingforafew seconds.
Therefore, these signals may notlast long
enough for theintegratedgaragedoor
opener. The signal is notrecognized during
programming. Comparable with Canadian
law, some U.S.garage door openers also
featurea"break".
Proceedasfollows:
Rif you live in Canada
Rif you have difficulties programmingthe
garagedoor opener (regardless of where
you live)when usingtheprogramming
steps
300Features
Stowage and features
Page 303 of 382
XPress and hold one of buttons to !on
the integrated garage door opener.
Afterashort time, indicator lamp lights
up yellow.
XRelease the button.
Indicator lamp flashes yellow.
XPress button %of garage door remote
control for two seconds, then release it
for two seconds.
XPress button %again for two seconds.
XRepeat this sequence on button %of
remotecontrol until indicator lamp
lights up green.
If indicator lamp turnsred, repeat the
process.
XContinue with the other programming
steps (see above).
Problems when programming
If you are experiencing problems
programmingthe integrated garage door
opener on the rear-view mirror, take noteof
the following instructions:
RCheck the transmitter frequencyofgarage
door drive remotecontrol .This can
usually be found on the back of the remote
control.
The integrated garage door opener is
compatible with devices that have units
which operate in the frequency range of
280to433MHz.
RReplace the batteries in garage door
remote control .This increases the
likelihood that garage door remote control
will transmitastrongand precisesignal
to the integrated garage door openerinthe
rear-view mirror.
RWhen programming, hold remote control
at varying distances and angles from the
button that you are programming. Try
various angles atadistance between 2and
12 inches (5to 30 cm) or at the same angle
but at varying distances.
RIf another remote control for the same
garage door drive is available, repeat the
same programming steps with this remote
control. Before performing these steps,
make sure that new batteries have been
installed in garage door drive remote
control .
RNote that some remote controls only
transmit foralimited amount of time (the
indicator lamp on the remote control goes
out). Press button %on remote control
again before transmission ends.
RAlign the antennacable of the garage door
opener unit. This can improve signal
reception/transmission.
Opening/closing the garage door
After it has been programmed, the integrated
garage door opener performs the function of
the garage door system remote control.
Please also read the operating instructions
for the garage door system.
XTurn the SmartKey to position2in the
ignition lock.
XPress button , $or !which you have
programmed to operate the garage door.
Garage door system withafixed code:
indicator lamp lights up green.
Garage door system witharolling code:
indicator lamp flashes green.
iThe transmitter will transmitasignal as
long as the button is pressed. The
transmission is halted afteramaximum of
ten seconds and indicator lamp lights
up yellow. Press button , $or !again
if necessary.
Clearing the memory
XTurn the SmartKey to position2in the
ignition lock.
XPress buttons and !.
The indicator lamp lights up yellow.
XPress and hold buttons and !until the
indicator lamp turns green.
Features301
Stowage and features
Z
Page 309 of 382
!Make sure that the windshieldwipers are
not folded away fromthe windshield. You
could otherwise damage the windshield
wipers or the hood.
XMake sure that the windshield wipers are
turned off.
XPull release lever on the hood.
The hood is released.
XReach into the gap, pull hood catch
handle up and lift the hood.
If you lift the hood by approximately
15 inches(40cm),the hood is opened and
held open automatically by the gas-filled
strut.
Closing thehood
XLower the hood and let it fall fromaheight
of approximately8inches(20 cm).
XCheck that the hood has engaged properly.
If the hood can be raised slightly,itisnot
properly engaged. Open it again and close
it withalittle more force.
Engine oil
General notes
Depending on the driving style, the vehicle
consumesupto0.9 US qt (0.8 liters) of oil
overadistanceof600 miles(1,000 km). The
oil consumption may be higher than this when
the vehicle is new or if you frequently drive at
high enginespeeds.
Depending on the engine, the oil dipstickmay
be inadifferent location.
When checking theoil level:
Rpark thevehicle onalevelsurface.
Rtheengineshould be switched off for
approximately fiveminutesiftheengineis
at normal operatingtemperature.
Rif theengineisnotat normal operating
temperature, e.g.ifthe engine was only
started briefly, wait about 30 minutes
before carrying out the measurement.
Checking the oil level using the oil
dipstick
XPull oil dipstick out of the dipstick guide
tube.
XWipe off oil dipstick .
XSlowly slide oil dipstick into the guide
tube to the stop, and take it out again.
If the level is between MIN mark $and
MAX mark ,the oil level is correct.
XIf the oil level has dropped to MIN mark
$or below, add 1.1 US qt (1.0 liter) of
engine oil.
Engine compartment307
Maintenance and care
Z
Page 314 of 382
Do not remove the SmartKeyfromthe
ignition lock. Do not open the driver's
door or front-passengerdoor when the
engine is switched off. Otherwise, the
automatic transmission selects park
positionPautomatically and locks the
wheels. You can prevent this by shifting
the automatic transmission toN
beforehand.
RVehicles with KEYLESS-GO:
Do not open the driver's door or front-
passenger door when the engine is
switched off. Otherwise, the automatic
transmission selects park positionP
automatically and locks the wheels.
Observe the following to make sure that the
automatic transmission stays in positionN:
XMake sure the vehicle is stationary and the
ignition is switched off.
XTurn the SmartKey to position2in the
ignition lock (Ypage 147).
Use the SmartKey instead of the Start/
Stop button on vehicles with KEYLESS-GO.
XDepress and hold the brake pedal.
XShift the automatic transmission to
positionN.
XRelease the brake pedal.
XRelease the electric parking brake.
XSwitch off the ignition and leave the
SmartKey in the ignition lock.
You can wash the vehicle in an automatic car
wash from the very start.
If the vehicle is very dirty, pre-wash it before
cleaning it in an automatic car wash.
After using an automatic car wash, wipe off
wax from the windshield and the wiper
blades. This will prevent smears and reduce
wiping noises caused by residue on the
windshield.
Washing by hand
In some countries, washing by hand is only
allowedatspecially equipped washing bays.
Observe the legal requirements in all
countries concerned.
XDo not use hot water and do not wash the
vehicle in direct sunlight.
XUseasoft sponge to clean.
XUseamild cleaning agent, such asacar
shampoo approved by Mercedes-Benz.
XThoroughly hose down the vehicle with a
gentle jet of water.
XDo not point the water jet directly towards
the air inlet.
XUse plenty of water and rinse out the
sponge frequently.
XRinse the vehicle with clean water and dry
thoroughly withachamois.
XDo not let the cleaning agent dry on the
paintwork.
When using the vehicle in winter, remove all
traces of road salt deposits carefully and as
soon as possible.
Power washers
GWARNING
The water jet fromacircular jet nozzle (dirt
blasters) can cause invisible exterior damage
to the tires or chassis components.
Componentsdamaged in this way may fail
unexpectedly. There isarisk of an accident.
Do not use power washers with circular jet
nozzles to clean the vehicle. Have damaged
tires or chassis components replaced
immediately.
!Always maintainadistance of at least
11.8in(30 cm) between the vehicleand the
powerwasher nozzle. Information about
thecorrectdistanceisavailablefromthe
equipmentmanufacturer.
Movethepower washernozzle around
when cleaning your vehicle.
Do not aim directly at any of the following:
Rtires
Rdoor gaps, roof gaps, joints, etc.
Relectrical components
312Care
Maintenance and care
Page 315 of 382
Rbattery
Rconnectors
Rlights
Rseals
Rtrim
Rventilation slots
Damaged seals or electrical components
can lead to leaks or failures.
Cleaning the paintwork
!Do not affix:
Rstickers
Rfilms
Rmagnetic plates or similar items
to painted surfaces.You could otherwise
damage the paintwork.
Scratches, corrosive deposits, areas affected
by corrosion and damage caused by
inadequate care cannot always be completely
repaired. In such cases, visitaqualified
specialist workshop.
XRemove dirt immediately, where possible,
while avoiding rubbing too hard.
XSoak insect remains with insect remover
and rinse off the treated areas afterwards.
XSoak bird droppings with water and rinse
off the treated areas afterwards.
XRemove coolant, brake fluid, tree resin,
oils, fuels and greases by rubbing gently
withacloth soaked in petroleum ether or
lighter fluid.
XUse tar remover to remove tar stains.
XUse silicone remover to remove wax.
If water no longer forms "beads" on the paint
surface, use the paint care products
recommended and approved by Mercedes-
Benz.This is the case approximately every
three to five months, depending on the
climate conditionsand the care product used.
If dirt has penetrated the paint surface or if
the paint has become dull, the paint cleaner
recommended and approved by Mercedes-
Benz should be used.
Do not use these care products in the sun or
on the hood while the hood is hot.
XUseasuitable touch-up stick,e.g. MB
Touch-Up Stick, to repair slight damage to
the paintwork quickly and provisionally.
Mattefinish care
!Never polish the vehicle or the light alloy
wheels. Polishing causes the finish to
shine.
!The following may cause the paint to
become shiny and thus reduce the matte
effect:
RVigorous rubbing with unsuitable
materials.
RFrequent use of car washes.
RWashing the vehicle in direct sunlight.
!Never use paint cleaner, buffing or
polishing products, or gloss preserver, e.g.
wax. These products are only suitable for
high-gloss surfaces. Their use on vehicles
with matte finish leads to considerable
surface damage (shiny, spotted areas).
Always have paintwork repairs performed
ataqualified specialist workshop, e.g. an
authorized Mercedes-BenzCenter.
!Do not use wash programs withahot wax
treatment under any circumstances.
Observe these notes if your vehicle has a
clear mattefinish. This will help you to avoid
damage to the paintwork due to incorrect
treatment.
These notes also apply to light alloy wheels
withaclear mattefinish.
iThe vehicle should preferably be washed
by hand usingasoft sponge, car shampoo
and plenty of water.
iUse only insectremover and car shampoo
from the range of recommended and
approved Mercedes-Benz care products.
Care313
Maintenance and care
Z
Page 316 of 382
Cleaning thevehicle parts
Cleaning thewheels
!Do notuse acidic wheel cleaning products
to remove brake dust. This could damage
wheel bolts and brake components.
!Do not park the vehicle for an extended
period straight after cleaning it, particularly
after having cleaned the wheels with wheel
cleaner. Wheel cleaners could cause
increased corrosion of the brake discs and
brake pads/linings. For this reason, you
should drive forafew minutes after
cleaning. Braking heats the brake discs and
the brake pads/linings, thus drying them.
The vehicle can then be parked.
Cleaning the windows
GWARNING
You could become trapped by the windshield
wipers if they start moving while cleaning the
windshieldorwiper blades. There isarisk of
injury.
Always switch off the windshieldwipers and
the ignition before cleaning the windshieldor
wiper blades.
!Do not use dry cloths, abrasive products,
solvents or cleaning agents containing
solvents to clean the inside of the windows.
Do not touch the insides of the windows
with hard objects, e.g. an ice scraper or
ring. There is otherwisearisk of damaging
the windows.
!Cleanthe water drainage channels of the
windshield and the rear window at regular
intervals. Deposits such as leaves, petals
and pollen may under certain
circumstances prevent water from draining
away.This can lead to corrosion damage
and damage to electronic components.
XCleanthe inside and outside of the
windows withadamp cloth andacleaning
product that is recommended and
approved by Mercedes-Benz.
Cleaningwiper blades
GWARNING
You could become trapped by the windshield
wipers if they start moving while cleaning the
windshield or wiper blades. There isarisk of
injury.
Always switch off the windshield wipers and
the ignition before cleaning the windshield or
wiper blades.
!Do not pull the wiper blade. Otherwise,
the wiper blade could be damaged.
!Do not clean wiper blades too often and
do not rub them too hard. Otherwise, the
graphite coating could be damaged. This
could cause wiper noise.
!Hold the wiper arm securely when folding
back. The windshield could be damaged if
the wiper arm smacks against it suddenly.
XFold the windshield wiper arms away from
the windshield.
XCarefully clean the wiper blades with a
damp cloth.
XFold the windshield wiper arms back again
before switching on the ignition.
Cleaningthe exterior lighting
!Only use cleaning agents or cleaning
cloths which are suitable for plastic light
lenses. Unsuitable cleaning agents or
cleaning cloths could scratchordamage
the plastic light lenses.
XCleanthe plastic lenses of the exterior
lighting usingawet sponge andamild
cleaning agent, e.g. Mercedes-Benzcar
shampoo or cleaningcloths.
Mirror turn signals
!Only use cleaningagents or cleaning
clothsthatare suitable for plastic lenses.
Unsuitable cleaningagents or cleaning
clothscould scratch or damagetheplastic
lenses of themirror turnsignals.
314Care
Maintenance and care
Page 319 of 382
mostly made of anodized aluminum and
can lose their shine if chrome polish is
used.Useadamp, lint-free cloth instead
when cleaning the trim pieces.
If the chrome-plated trim pieces are very
dirty, you can useachrome polish. If you
are unsure as to whether the trim pieces
are chrome-plated or not, consult an
authorized Mercedes-Benz Center.
XWipe the wooden trim and trim pieces with
adamp, lint-free cloth, e.g.amicrofiber
cloth.
XHeavy soiling:use car care and cleaning
products recommended and approved by
Mercedes-Benz.
Cleaning the seat covers
General notes
!Do not use microfiber cloths to clean
genuine leather, artificial leather or
Alcantara® covers. If used often, these can
damage the cover.
iNote that regularcare is essential to
ensure that theappearanceand comfort of
thecoversisretainedovertime.
Genuineleather seat covers
Leather isanatural product.
It exhibits natural surface characteristics, for
example:
RDifferences in the texture
RSignsofstretchingand marking
RSlightnuances of color
Theseare characteristics of leather and not
material defects.
!To retain thenatural appearanceofthe
leather,observethefollowingcleaning
instructions:
RClean genuine leathercovers carefully
withadamp cloth and then wipe the
covers down withadry cloth.
RMake sure that the leather does not
become soaked. It may otherwise
become rough and cracked.
ROnly use leather care agents that have
been tested and approved by Mercedes-
Benz.You can obtain these from a
qualified specialist workshop.
Seat covers of other materials
!Observe the following when cleaning:
RClean artificial leather covers withacloth
moistened withasolution containing
1% detergent (e.g. dish washing liquid).
RClean cloth covers withamicrofiber
cloth moistened withasolution
containing 1% detergent (e.g. dish
washing liquid). Rub carefully and always
wipe entireseat sectionstoavoid leaving
visible lines. Leave the seat to dry
afterwards. Cleaning results depend on
the type of dirt and how long it has been
there.
RClean Alcantara® covers withadamp
cloth. Make sure that you wipe entire
seat sectionstoavoid leaving visible
lines.
Cleaning the seat belts
GWARNING
Seat belts can become severely weakened if
bleached or dyed. This could cause the seat
belts to tear or fail, for instance, in the event
of an accident.This poses an increased risk
of injury or fatal injury.
Never bleach or dye the seat belts.
!Do not clean the seat belts using chemical
cleaning agents. Do not dry the seat belts
Care317
Maintenance and care
Z