lock MERCEDES-BENZ CLS 2014 Repair Manual

The blueindicator lamp in the
instrument cluster lights up when the high-
beam headlamps are switched on.
XTo switch off the high-beam
headlamps:move the combination switch
back to its normal position.
The blueindicator lamp in the
instrument cluster goes out.
iVehicles with Adaptive Highbeam Assist:
when Adaptive Highbeam Assist is active,
it controls activation of the high-beam
headlamps (Ypage 121).
High-beam flasher
High-beam headlamps
Turn signal, right
$High-beam flasher
!Turn signal, left
XTo switch on:turn the SmartKey in the
ignition lock to position1or2,orstart the
engine.
XPull the combination switch in the direction
of arrow$.
Hazard warning lamps
XTo switch on the hazard warning lamps:
press button.
All turn signals flash. If you now switch on
aturn signal using the combination switch,
only the turn signal lamp on the
corresponding side of the vehicle will flash.
XTo switch off the hazard warning
lamps:press button.
The hazard warning lamps automatically
switch on if:
Ran air bag is deployed
Rthe vehicle decelerates rapidly from a
speed of more than 45 mph (70 km/h) and
comes toastandstill
The hazard warning lamps switch off
automatically if the vehicle reachesaspeed
of over6mph (10 km/h) again afterafull
brake application.
iThe hazard warning lamps still operate if
the ignition is switched off.
Headlampcleaning system
The headlamps are cleaned automatically if
the "Wipe with washer fluid" function is
operated five times (Ypage 125)while the
lightsare on and the engineisrunning. When
you switchoff the ignition, the automatic
headlamp cleaning systemisreset and
counting is resumed from 0.
120Exterior lighting
Lights and windshield wipers

Cornering lightfunction
The cornering light function improves the
illumination of the road overawideanglein
the direction you are turning, enabling better
visibility in tight bends, for example. It can
only be activated whenthe low-beam
headlamps are switched on.
Active:
Rif you are driving at speeds below 25 mph
(40 km/h)and switch on the turn signal or
turn the steering wheel
Rif you are driving at speeds between
25 mph(40km/h)and 45 mph(70km/h)
and turn the steering wheel
Not active:if you are driving at speeds above
25 mph (40 km/h) or switch off the turn
signalorturn the steering wheel to the
straight-ahead position.
The cornering lamp may remain lit forashort
time, but is automatically switched off after
no more than three minutes.
Active light function
The active light function isasystem that
moves the headlamps according to the
steering movements of the front wheels.In
this way, relevant areasremain illuminated
while driving. Thisallowsyou to identify
pedestrians, cyclists and animals.
Active:whenthe lights are switched on.
Adaptive Highbeam Assist
Important safety notes
GWARNING
Adaptive Highbeam Assist does not recognize
road users:
Rwho have no lights, e.g. pedestrians
Rwho have poor lighting, e.g. cyclists
Rwhose lighting is blocked, e.g. byabarrier
In very rare cases, Adaptive Highbeam Assist
may fail too recognize other road users that
have lights, or may recognize them too late.
In this or similar situations, the automatic
high-beam headlamps will not be deactivated
or activated regardless. There isarisk of an
accident.
Always carefully observe the traffic conditions
and switch off the high-beam headlamps in
good time.
Exterior lighting121
Lights and windshield wipers
Z

Interior lighting
Overview of interior lighting
Frontoverhead control panel
To switch therear interiorlighting
on/off
To switchthe automatic interior
lighting control on/off
$To switchthe right-handfront
reading lamp on/off
!\rTo switch the front interior lighting
on/off
To switch the left-hand front reading
lamp on/off
Rear-compartment overheadcontrol panel
To switch the right-hand reading
lamp on/off
To switch the left-hand reading lamp
on/off
Interior lighting control
General notes
In order to prevent the vehicle's battery from
discharging, the interior lighting functions are
automatically deactivated after some time
unless the SmartKey is in position2in the
ignitionlock.
The color and brightness of the ambient
lighting may be set using the on-board
computer (Ypage 231).
Automatic interior lighting control
Frontoverhead control panel
To switch the rear interior lighting
on/off
To switch the automatic interior
lighting control on/off
$To switch the right-hand reading
lamp on/off
!\rTo switch the front interior lighting
on/off
To switch the left-hand reading lamp
on/off
XTo activate/deactivate:press the
button.
When the automatic interior lighting
control is activated, the button is flush with
the overhead control panel.
Interior lighting123
Lights and windshiel dw ipers
Z

The interior lighting automatically switches
on if you:
Runlock the vehicle
Ropenadoor
Rremove the SmartKey from the ignition lock
The interior light is activated forashort while
when the SmartKey is removed from the
ignition lock. You can activatethis delayed
switch-off using the on-board computer
(Ypage 232).
Manualinterior lighting control
Frontoverhead control panel
To switch the rear interior lighting
on/off.
To switch the automatic interior
lighting control on/off
$To switch the right-hand reading
lamp on/off
!\rTo switch the frontinterior lighting
on/off
To switch the left-hand reading lamp
on/off
XTo switch the front interior lighting on/
off:press the\rbutton.
XTo switch the rear interior lighting on/
off:press thebutton.
XTo switch the reading lampson/off:
press thebutton.
Crash-responsive emergency lighting
The interior lighting is activated automatically
if the vehicle is involved in an accident.
XTo switch off the crash-responsive
emergency lighting:press the hazard
warning lamp button.
or
XLock and then unlock the vehicle using the
SmartKey.
Replacing bulbs
Important safety notes
Xenon bulbs
GDANGER
Xenon bulbs carryahigh voltage. You can get
an electric shock if you remove the cover of
the Xenon bulb and touch the electrical
contacts. There isarisk of fatal injury.
Never touch the parts or the electrical
contacts of the Xenon bulb. Always have work
on the Xenon bulbs carried out ataqualified
specialist workshop.
Bulbs and lamps are an importantaspect of
vehicle safety. You must therefore make sure
that these function correctly at all times.
Have the headlamp setting checked regularly.
LED lamps
You can neither replace Xenon bulbsnor LED
bulbs. Have LED bulbschanged ataqualified
specialist workshop.
Bulbs and lamps are an important aspect of
vehicle safety. You must therefore make sure
that these function correctly at all times.
Have the headlamp setting checked regularly.
Other bulbs
GWARNING
Bulbs, lamps and connectors can get very hot
when operating. If you changeabulb, you
124Replacing bulbs
Lights and windshield wipers

could burn yourselfonthese components.
There isarisk of injury.
Allow these components to cool down before
changingabulb.
There are bulbs other than Xenon and LED
bulbs that you cannot replace. Replace only
the bulbs listed (Ypage 125). Have the bulbs
that you cannot replace yourself changed at
aqualified specialist workshop.
If you require assistance changing bulbs,
consultaqualified specialist workshop.
Do not touch the glass tube of new bulbs with
your bare hands. Even minor contamination
can burn into the glass surface and reduce
the service life of the bulbs. Always usealint-
free cloth or only touch the base of the bulb
when installing.
Only use bulbs of the correct type.
If the new bulb still does not light up, consult
aqualified specialist workshop.
Bulbs and lamps are an important aspect of
vehicle safety. You must therefore make sure
that these function correctly at all times.
Have the headlamp settingchecked regularly.
Overview: changing bulbs/bulb types
You can change the following bulbs. The bulb
type can be found in the legend.
Tail lamp
Backup lamp:W16W
Changing the rear bulbs
Backup light
Lamp unit
XSwitch off the lights.
XOpen the trunk.
XReach up into the side paneling and pull
downwards until the lamp cluster is easily
accessible.
XPress the detent of connectorand pull
out connector.
XUseasuitable tool to loosen and remove
four nuts.
XRemove the entire lamp cluster.
XTurn bulb holder$counter-clockwise and
pull it out.
XPull out bulb.
XInsert the new bulb into bulb holder$.
XInsert bulb holder$into the lamp and turn
it clockwise.
XRe-insert the lamp cluster.
XTighten four nuts.
XPush in connectoruntil it engages.
XInsert the side paneling.
Windshield wipers
Switching the windshield wiperson/
off
!Do not operatethe windshield wipers
when the windshield is dry, as this could
damage the wiper blades. Moreover, dust
Windshield wipers125
Lights and windshield wipers
Z

Depending on the equipment level of your
vehicle, there aretwo variants of wiperblade;
these are installed and removed in different
ways. Based on the diagrams,checkwhich
system is installed in your vehicle.
Changing the wiper blades (version 1)
Removing the wiper blades
XRemove the SmartKey from the ignition
lock or turn it to position0(KEYLESS-GO).
XFold the wiper arm away from the
windshield until it engages.
XSet the wiper blade at right angles to the
wiper arm.
XRemove the wiper blade from the retaining
pin on the wiper arm in the direction of the
arrow.
Installing the wiper blades
XPush the new wiper blade onto the
retaining pin on the wiper arm in the
opposite direction to the arrow.
Make sure that the wiper blade slides fully
onto the retaining pin on the wiper arm.
XTurn the wiper blade parallel to the wiper
arm.
XFold the wiper arm back onto the
windshield.
Changing the wiper blades (version 2)
Removing the wiper blades
XRemove the SmartKey from the ignition
lock or turn it to position0(KEYLESS-GO).
XFold the wiper arm away from the
windshield until it engages.
XFirmly press release knoband pull the
wiper blade upwards from the wiper arm in
the direction of the arrow.
Installing the wiper blades
XPosition the new wiper blade in the retainer
on the wiper arm and slide it into place in
the opposite direction from the arrow.
The wiper blade audibly engages.
XMake sure that wiper blade is seated
correctly.
XFold the wiper arm back onto the
windshield.
Windshield wipers127
Lights and windshield wipers
Z

Problems with the windshield wipers
ProblemPossible causes/consequences andSolutions
The windshield wipers
are jammed.
Leaves or snow, for example, may be obstructing the windshield
wiper movement.The wiper motor has been deactivated.
XFor safety reasons, you should remove the SmartKey from the
ignition lock.
or
XSwitch off the engine using the Start/Stop button and open the
driver's door.
XRemove the cause of the obstruction.
XSwitch the windshield wipers back on.
The windshield wipers
fail completely.
The windshield wiper drive is malfunctioning.
XSelect another wiper speed on the combination switch.
XHave the windshield wipers checked ataqualified specialist
workshop.
128Windshield wipers
Lights and windshield wipers

Information aboutusing 3-zone
automatic climate control
Automatic climate control
The 3-zone automatic climate control is only
available on vehicles for Canada.
The following contains instructions and
recommendations to enable you to get the
most out of your automatic climate control.
RActivate climate control using the\rand
buttons. The indicatorlamps above
the\randbuttons light up.
RIn automatic mode, you can also use the
buttontosetaclimate mode
(FOCUS/MEDIUM/DIFFUSE). The
MEDIUM levelisrecommended.
RSet thetemperaturetof72‡(22 †).
ROnly use the"Windshield defrosting"
function briefly until thewindshield is clear
again.
ROnly use air-recirculation modebriefly, e.g.
if there are unpleasantoutside odorsor
when inatunnel. The windows could
otherwise fog up, since no fresh air is drawn
intothevehicleinair-recirculation mode.
RUse theZONEfunction to adopt the
temperature settingsonthedriver's side
for the front-passenger side and the rear
compartment as well. The indicatorlamp
above thebutton goes out.
RUse the residual heat function if you want
to heat or ventilate the vehicle interior
when the ignition is switched off. The
residual heat function can only be activated
or deactivated with the ignition switched
off.
RVehicles with COMAND Multimedia-
System:if you change the settings of the
climate control system, the climate status
displayappears for approximately three
seconds at the bottom of the screen in the
COMAND display. See also the separate
COMAND operating instructions. You will
see the current settings of the various
climate control functions.
ECO start/stop function
During automatic engine switch-off,the ECO
start/stop function only operates at a
reduced capacity. If you require the full
climate control output, you can switch off the
ECO start/stop function by pressing the ECO
button (Ypage 152).
Operating the climate control
systems
Switching climate control on/off
Points to observe before use
When the climate control is switched off, the
air supply and air circulation are also
switched off. The windows could fog up.
Therefore, switch off climate control only
briefly
iActivate climate control primarily using
the\rbutton (Ypage 137).
Activating/deactivating
XTurn the SmartKey to position2in the
ignition lock (Ypage 147).
XTo switch on:press the\rbutton on
the control panel for the climate control.
The indicator lamp in the\rbutton lights
up. Airflow and air distribution are set to
automatic mode.
or
XPress thebutton.
The indicator lamp in thebutton goes
out. The previously selected settings are
restored.
XTo switch off:press thebutton.
The indicator lamp in thebutton lights
up.
Operating the climate control systems135
Climat ec ontrol

Problems with the "Cooling with air dehumidification" function
ProblemPossible causes/consequences andSolutions
The indicator lamp in
thebutton
flashes three times or
remains off. The
"Cooling with air
dehumidification"
function cannot be
switched on.
Cooling with air dehumidification has been deactivated due to a
malfunction.
XVisitaqualified specialist workshop.
Setting climate control to automatic
Points to observe before use
In automatic mode, the set temperature is
maintained automatically ataconstant level.
The system automatically regulates the
temperature of the dispensed air, the airflow
and the air distribution.
The automatic mode functions optimally
when the "Cooling with air dehumidification"
function is activated. If necessary, cooling
with air dehumidification can be deactivated.
If you deactivate the "Cooling with air-
dehumidification" function, the air inside the
vehicle will not be cooled. The air inside the
vehicle will also not be dehumidified. The
windows can fog up more quickly. Therefore,
deactivate the cooling with air-
dehumidification function only briefly.
Activating/switching
XTurn the SmartKey to position2in the
ignition lock (Ypage 147).
XSet the desired temperature.
XTo activate:press the\rbutton.
The indicator lamp in the\rbutton lights
up. Automatic air distribution and airflow
are activated.
i3-zone automatic climate control: when
automatic mode is activated, you can
selectaclimate mode (Ypage 137).
XTo switch to manualmode:press the
button.
or
XPress theorbutton.
The indicator lamp in the\rbutton goes
out.
Adjusting the climate mode settings
The "Set climate mode" function is only
available with 3-zone automatic climate
control.
You can select the following climate mode
settings in automatic mode:
FOCUS high airflow that is set slightly
cooler
MEDIUM medium airflow, standard setting
DIFFUSE low airflow that is set slightly
warmer and with less draft
XTurn the SmartKey to position2in the
ignition lock (Ypage 147).
XPress the\rbutton.
XPress thebutton repeatedly until the
desired climate mode appears in the
display.
Operating the climate control systems137
Climate control

Setting the temperature
Dual-zone automatic climate control
Differenttemperatures can be set for the
driver's and front-passenger sides.
XTurn the SmartKey to position2in the
ignition lock (Ypage 147).
XTo increase/reduce:turn temperature
controlor%clockwise or counter-
clockwise (Ypage 131).
Only change the temperature settingin
small increments. Start at 72‡(22 †).
3-zone automatic climate control
Automatic climate control zones
You can select different temperature settings
for the driver's and front-passenger sides as
well as for the rear compartment.
XTurn the SmartKey to position2in the
ignition lock (Ypage 147).
XTo increase/reduce the temperature in
the front compartment:turn temperature
controlor%clockwise or counter-
clockwise (Ypage 134).
Only change the temperature settingin
small increments. Start at 72‡(22 †).
XTo increase/reduce the temperature in
the rear compartment using the front
control panel:press thebutton.
The indicator lamp in thebutton goes
out.
XTurn temperature controlclockwise or
counter-clockwise (Ypage 134).
Only change the temperature settingin
small increments. Start at 72‡(22 †).
The temperature settingfor the driver's
side is adopted for the rear compartment
and the front-passenger side.
XTo increase/reduce the temperature in
the rear compartment using the rear
control panel:press theor
button on the rear control panel.
Only change the temperature settingin
small increments. Start at 72‡(22 †).
Setting the air distribution
Air distribution settings
Directsair through the center and side
air vents
Directsair through the footwell air
vents
Directsair through the center, side and
footwell vents

Directsair through the defroster vents
Directsthe airflow through the
defroster, center and side air vents
(Canada only)
Directsair through the defroster and
footwell vents
Directsthe airflow through the
defroster, center and side air vents, as
well as the footwell air vents(Canada
only)
iRegardless of the air distribution setting,
airflow is always directed through the side
air vents. The side air ventscan only be
closed when the controls on the side air
ventsare turned downwards.
Setting the air distribution
XTurn the SmartKey to position2in the
ignition lock (Ypage 147).
XPress thebutton repeatedly until the
desired symbol appears in the display.
138Operating the climate control systems
Climate control