key MERCEDES-BENZ E-CLASS COUPE 2009 Owners Manual

0079
To lock
X Insert the hex-socket wrench into the roof
lock.
X Turn the hex-socket wrench anti-clockwise
0079 as far as possible.
X Have the soft-top mechanism repaired
immediately at aqualified specialist work-
shop, e.g. aMercedes-Benz Service
Centre.
i Press the soft-top compartment cover
again if the boot lid cannot be opened.
! Do not under any circumstances open the
boot lid with the emergenc ykey. You could
otherwise damage the boot lid and the soft-
top compartment cover. Boot
! The boot lid swings upwards when
opened. Therefore, make sure that there is
sufficient clearance above the boot lid.
If the boot can no longer be unlocked with the
key or KEYLESS GO*:
X Remove the emergenc ykey element from
the key (Y page 249). X
Insert the emergenc ykey element into the
boot lid lock as far as the stop.
X Turn the emergenc ykey element anti-
clockwise as far as it will go to position
004A and pull the boot lid handle.
The boot is unlocked.
X Turn the emergenc ykey element back and
remove it. Releasing the parking lock manually
(vehicles with automatic transmis-
sion*)
In the event of an electrical fault, it is possible
to release the selector lever lock manually to
move it out of position P,e.g. if you wish to
tow the vehicle away. X
Depress the parking brake firmly.
X Prise out selector lever gaiter 0046with aflat,
blunt object ,(e. g. ascrewdriver wrapped Locking/unlocking in an emergency
255Practical advice
*optional
207_AKB; 2; 3, en-GB
mkalafa,
Version: 2.11.8.1 2009-07-23T10:23:49+02:00-Seite 255 Z

X
Push the emergenc ykey into two
holes 0046between the head restraints until
cover 0047releases.
X Remove cover 0047. X
Turn handwheel 0046in the direction of the
fronts eat to lower the head restraints. AIRCAP*
-fitting/removing the wind
deflector (Cabriolet)
You will need a4mmhex-socket wrench to
fit and remove the AIRCAP draught stop. Removing the AIRCAP draught stop
X Turn the key to position 2in the ignition
lock.
X Open the soft top fully (Y page 160).
X Extendt he head restraints in the rear com-
partmen t(Y page 69). Bolts on the AIRCAP draught stop between the
head restraints in the rear compartment
X
Use the 4mmhex-socket wrench to turn
the bolts on both sides anti-clockwise by
about 90° and loosen them.
X Pull the bolts out of the mountings on the
head restraints. X
Pull the AIRCAP draught stop out of the
guide rails in the direction of the arrow.
Make sure that you pull the AIRCAP draught
stop forwards slightly when doing so. Fitting the AIRCAP draught stop
X Turn the key to position 2in the ignition
lock.
X Open the soft top fully (Y page 160).
X Extendt he head restraints in the rear com-
partmen t(Y page 69). 258
AIRCAP* -fitting/removing the wind deflector (Cabriolet)Practical advice
*o ptional
207_AKB; 2; 3, en-GB
mkalafa,
Version: 2.11.8.1 2009-07-23T10:23:49+02:00-Seite 258

X
Keeping the AIRCAP draught stop horizon-
tal, guide it into the slot betwee nthe head
restraints in the direction of the arrow with
both racks straight down.
X Push the AIRCAP draught stop down until
the bolts are at the same heigh tasthe
mountings on the head restraints.
X Insert the bolts into the mountings on both
sides.
X Turn the bolts firmly with the 4mmhex-
socket wrench until they engage.
The markings on the bolts are vertical. Changing batteries (key)
Notes
It is advisabletoh ave the batteries replaced
at aq ualified specialist workshop, e.g. at a
Mercedes-Benz Service Centre. G
Risk of poisoning
Batteries contain toxic and caustic substan-
ces. For this reason, keep batteries awayf rom
children.
If ab attery is swallowed, consult adoctor
immediately. H
Environmental note
Do not dispose of batteries with the house-
hold rubbish. They contain highl ytoxic sub-
stances.
Take discharged batteries to aqualified spe-
cialist workshop, e.g. aMercedes-Benz Service Centre, or to
aspecia lcollection point
for old batteries. Key
Checking the battery X
Press the 0037or0036 button.
The battery is working properl yifthe bat-
tery charge indicator lamp lights up briefly.
Removing/installing the battery You require
aCR20253Vc ell battery.
X Remove the emergency key element from
the key (Y page 249). X
Press the emergency key element into the
opening in the key in the direction of
arrow 0047until cover 0046of the battery tray
opens. Be sure that yourf ingers are not
stopping the cover from opening. Changing batteries (key)
259Practical advice
207_AKB; 2; 3, en-GB
mkalafa,V ersion: 2.11.8.1
2009-07-23T10:23:49+02:00
-Seite 259 Z

X
Remove th ecover of th ebattery tray.
X Repeatedly tap th ekeyagainst your palm
until battery 008Afallsout of th ekey.
X Inser tthe newb attery wit hthe positive
pole facin gupwards. Use alint-free cloth to
do so.
X Inser tthe fron ttab soft hebattery tray's
cover first and then press to close it.
X Chec kthe function of all ke ybuttons on the
vehicle. Changin
gbulbs Notes on changin
gbulbs
i If you need assistanc einchangin gthe
bulbs ,contac taqualified specialist work-
sho pwhichh as th eneces saryspecialist
knowledge and tools to carry out th ework
required. Mercedes-Ben zrecommends
that you use aMercedes-Ben zServi ce
Centr efor this purpose .Inparticular, work
relevan ttosafetyoro nsafety-related sys-
tems mus tbecarriedout at aqualified spe-
cialist workshop.
Bulb sand lamp sare an important aspect of
vehicl esafety. You mus tthe refor emakes ure
that these function correctl yatall times.
Hav ethe headlamp setting schecked regu-
larly. Only use th etypes of bulbs specified
here. If th enew bulb still does no tligh tup,
consult aqualified specialist workshop.
Do no ttou ch th eglasstub eofn ewbulbs with
your bare hands. Even minor contamination
can burn into th eglasssurfac eand reduce th
es ervic elife of th ebulbs .Always use alint-
free cloth or only touch th ebase of th ebulb
when fitting. G
Ris
kofi njury
Bulb sand lights can become ver yhot.F or this
reason ,allow them to cool down before
changin gthem. Otherwise ,you could burn
yourself when you touch them.
Kee pbulbs out of th ereac hofc hildren .Oth-
erwise, they could damage them, for example,
and injur ethemselves.
Never use abulb whic hhas been dropped.
Suc hab ulb may explod eand injur eyou.
Halogen bulbs are pressurised and could
explod ewhen you chang ethem, especially if
they are ver yhot.Y ou should therefor ewear
eye protection and gloves when you are
changin gthem. G
Ris
kofi njury
Xenon bulbs carry ahigh voltage. You could
get an electric shock and be seriously or even
fatally injured if you touch th eelectric con-
tacts on xeno nbulbs .Therefore ,never
remove th ecover from xeno nbulbs.
Do no tcha ng ex enon bulbs yourself ,but have
them replaced at aqualified specialist work-
sho pwhichh as th eneces saryspecialist
knowledge and tools to carry out th ework
required.
Mercedes-Ben zrecommends that you use a
Mercedes-Ben zServic eCentr efor this pur-
pose. In particular, wor krelevan ttosafetyor
on safety-related systems mus tbecarriedout
at aq ualified specialist workshop. 260
Changing bulbsPractical advice
207_AKB; 2; 3, en-GB
mkalafa,
Version: 2.11.8.1 2009-07-23T10:23:49+02:00-Seite 260

Replacing the wiper blades
G
Ris
kofa ccident
The windscreen will not longer be wiped prop-
erl yift he wiper blades are worn. Thi scould
prevent yo ufrom observing the traffic condi-
tions ,thereby causing an accident. Replace
the wiper blades twice ayear, ideall yinspring
and autumn. G
Ris
kofa ccident
The wiper arm scould star tmoving and cause
an injury if yo uleave the windscreen wipers
switched on.
Remove the key from the ignition lock before
replacing the wiper blades.
! To avoid damaging the windscreen wiper
blades, make sure that yo utouch only the
wiper arm of the windscreen wiper. To remove
X Remove the key from the ignition lock or
turn the key to position 0(KEYLESS-GO).
X Fol dthe wiper arm away from the wind-
screen unti litengages.
X Set the wiper blad eatright angle stothe
wiper arm. X
Remove the wiper blad efrom the retainer
on the wiper arm in the direction of the
arrow. Fitting
X Slide the new wiper blad einto the retainer
on the wiper arm in the opposite direction
to the arrow.
X Turn the wiper blad eparalle ltot he wiper
arm.
X Fol dthe wiper arm back onto the wind-
screen. Flat tyre
Flat tyre equipmen
tvariants
Your vehicl emay be equipped with:
R aT IREFIT kit (Y page 207)
R a" Minispare" emergency spare wheel*
(Y page 208)
R the MOExtended run-flat sys-
tem* (Y page 272) Preparing the vehicle
i Vehicl epreparation is not necessary on
vehicles with MOE tyres*.
X Stop the vehicl easfar away as possible
from traffic on solid ,non-slipper yand level
ground.
X Switch on the hazard warning lamps.
X Firmly depres sthe parking brake.
X Vehicles with manual transmission:
engage firs torreverse gear.
X Vehicles with automati ctransmis-
sion*: move the selector lever to P.
X All occupants mus tget ou tofthe vehicle.
Make sure that they are not endangered as
they get ou tofthe vehicle.
X Make sure that no one is nea rthe danger
are aw hilst awheel is being changed .Any-
one wh oisnot directl yassisting in the
wheel change should, for example, stand
behind the barrier.
X Switch off the engine. Flat tyre
263Practical advice
*optional
207_AKB; 2; 3, en-GB
mkalafa
,V ersion: 2.11.8.1
2009-07-23T10:23:49+02:00
-Seite 263 Z

X
Vehicles withou tKEYLESS GO*:remove
the key from the ignition lock.
X Vehicles with KEYLES SGO*: openthe
driver' sdoor.
The on-board electronics have status 0,
which is the same as the key having been
removed.
X Ge toutof the vehicle.
X Close the driver' sdoor.
X Place the warning triangl e(Ypage 206) at
as uitabl edistance. Observe lega lrequire-
ments. Usin
gthe TIREFI Tkit
Yo uc an us ethe TIREFIT kit to sea lsmall
punctures, particularly thos einthe tyre tread.
Yo uc an us eTIREFIT at outsid etemperatures
dow nto- 20†. G
Risk of accident
In the following case syoursafety is especially
endangered, as tyre sealant is insufficient if:
R there are cuts or puncture sinthe tyre
greater than 4mm.
R the wheel rim is damaged.
R youh aved riven at very low tyre pressures
or on aflatt yre.
Do not drive any further. Consul taqualified
specialist worksho pwhich ha sthe necessary
specialist knowledg eand tool stocarryo ut
the work required.
Mercedes-Benz recommend sthat yo uuse a
Mercedes-Benz Service Centre for this pur-
pose. In particular, work relevant to safety or
on safety-related systems mus tbec arrie dout
at aq uali fied specialist workshop.
X Do not remove any foreign objects which
have penetrated the tyre ,e.g. screw sor
nails.
X Remove the TIREFIT kit, the accompanying
"max. 80 km/h "sticke rand the electri cair
pump from the stowag ewellu nderneath the luggage compartment floor
(Y
page 207). X
Affix part 0046of the sticke rwithin the driv-
er's field of vision.
X Affix part 0047of the sticke rnearthe valve
on the wheel with the defectiv etyre. G
Risk of injury
TIREFIT mus tnot come into contact with your
skin, eyes or clothing.
R If TIREFIT come sinto contact with your
eyes or skin, immediatel yrinse thoroughly
with clean water.
R Change ou tofclothing which ha scome into
contact with TIREFIT immediately.
R If an allergi creaction occurs, consult adoc-
tor immediately.
Kee pTIREFIT away from children.
R If TIREFIT is swallowed, immediatel yrinse
your mouth ou tthoroughly and drink plenty
of water.
R Do not induce vomiting. Consul tadoctor
immediately.
R Do not inhale TIREFIT fumes.
i If TIREFIT leaks out, allow it to dry .Itcan
then be removed like alayer of film.
If yo uget TIREFIT on your clothing, have it
cleane dassoona spossible with perchloro-
ethylene. 264
Flat tyrePractical advice
*o
ptional
207_AKB
;2;3,en-GB
mkalafa ,V ersion: 2.11.8.1
2009-07-23T10:23:49+02:00
-Seite 264

G
Risk of injury
Compl ywitht he manufacturer' ssafety
instructions shown on the sticke ronthe elec-
tric ai rpum p.
You rvehicle may be equipped with one of two
different ai rpum ps. Version 1can be identi-
fie dbyt he flap, behind which the hos ewith
the pressure gaug eand cable are located;
version 2hasap ressure gaug eintegrate din
the electri cairpump.
Version 1 X
Ope nflap 0047on the electri cairpump.
X Pull connector 0086with cable and ai rpump
hose 0087outoft he housing.
X Screw ai rpum phose 0087onto flange 006Eof
TIREFIT sealant fille rbottle 0046.
X Place TIREFIT sealant fille rbottle 0046head
downwards into recess 008Aof the electric
ai rp um p. X
Remove the cap from valve 0070on the faulty
tyre. X
Make sure pressure release screw 0071on
pressure gauge 0072is fully closed.
X Screw fille rhose 006Fonto valve 0070.
X Inser tconnector 0086into the socke tofthe
cigarette lighter* (Y page 173) or into a
12 Vp ower socke t(Ypage 174) in your
vehicle.
X Vehicles without KEYLES SGO*: turn the
key to position 2(Y page 65) in the ignition
lock.
X Vehicles with KEYLES SGO*: press the
Start/Stop button twice (position
2 (Y page 66)).
X Press on/off switch 0088on the electri cair
pump to I.
The electri cairpump is switched on. The
tyre is inflated.
i First, TIREFIT is pumpe dinto the tyre .The
pressure can briefl yrisetoa round 5bar.
Do no tswitcho ff the electric pump dur-
ing this phase.
X Let the electri cpum prun for five minutes.
The tyre shoul dthen have apressure of at
leas t1.8 bar.
! Do not operate the electri cairpump for
longer than eight minutes at atime without
ab reak. It may otherwise overheat.
The ai rpum pcan be operate dagain once
it ha scooled down. Flat tyre
265Practical advice
*optional
207_AKB
;2;3,en-GB
mkalafa ,V ersion: 2.11.8.1
2009-07-23T10:23:49+02:00
-Seite 265 Z

Versio
n2 X
Pull connector 0088with cable and ai rpump
hose 0086outoft he housing.
X Screw ai rpum phose 0086onto flange 0087of
TIREFIT sealant fille rbottle 0046.
X Place TIREFIT sealant fille rbottle 0046 head
downwards into recess 0047of the electric
ai rp um p. X
Remove the cap from valve 006Eon the faulty
tyre.
X Screw fille rhose 006Fonto valve 006E.
X Insert connector 0088into the socke tofthe
cigarette lighter* (Y page 173) or into a
12 Vp ower socke t(Ypage 174) in your
vehicle.
X Vehicles withou tKEYLESS GO*:turn the
key to position 2(Y page 65) in the ignition
lock.
X Vehicles with KEYLES SGO*: press the
Start/Sto pbutton twice (position
2 (Y page 66)). X
Press on/of fswitch 008Aon the electri cair
pump to I.
The electri cairpump is switched on. The
tyr eisi nflated.
i First, TIREFIT is pumpe dinto the tyre. The
pressure can briefl yrisetoa round 5bar.
Do no tswitcho ff the electric pump dur-
in gt his phase.
X Let the electri cpum prun for fiv eminutes.
The tyr eshoul dthen have apressure of at
leas t1.8 bar.
! Do not operate the electri cairpump for
longer tha neight minutes at atime without
ab reak. It ma yotherwise overheat.
The ai rpum pcan be operated agai nonce
it ha scooled down.
If ap ressure of 1.8 bar is no treached
afte rfivem inutes:
X Switch off and disconnect the electri cair
pump and drive the vehicl eforwards or
backwards approximatel y10m.
Thi sd istributes the TIREFIT more evenly.
X Remove TIREFIT sealant fille rbottle 0046
from the electri cpum p.
X Pump up the tyr eagain. G
Ris
kofa ccident
If ap ressure of 1.8 ba risnot achieved after
fiv em inutes, the tyr eistoo badl ydam aged.
Do not drive any further .Consult aquali fied
specialist workshop which ha sthe necessary
specialist knowledge and tool stocarry out
the work required .Mercedes-Benz recom-
mend stha tyou useaM ercedes-Benz Service
Centre for thi spurpose. In particular, work
relevant to safety or on safety-relate dsys-
tems must be carrie doutataq uali fied spe-
cialist workshop. Flat tyre
267Practical advice
*optional
207_AKB; 2; 3, en-GB
mkalafa,
Version: 2.11.8.1 2009-07-23T10:23:49+02:00-Seite 267 Z

water
.Consult adoctor if
necessary. Wear eye protection.
Keep children away.
Observe this Owner's Man-
ual.
H
Environmenta
lnote
Do not dispos eofbatteries in th ehousehold
rubbish. Dispose of defectiv ebatteries in an
environmentally responsible manner .Take
them to aMercedes-Ben zServic eCentre or
to as pecial collection poin tfor old batteries. G
Risk of injury
For safet yreasons ,Mercedes-Ben zrecom-
mends that you only use batteries which have
been tested and approved for your vehicle by
Mercedes-Benz. These batteries provide
increase dimpac tprotection to prevent vehi-
cle occupant sfroms ufferin gacid burns
should th ebattery be damaged in th eevent
of an accident.
To prevent acid burns, observe th efollowing
safet ynotes when handling batteries:
R do not lean over th ebattery.
R do not place any metal object sonabattery.
Otherwise, you could cause ashor tcircuit
and th ebattery's gas mixtur ecould ignite.
R mak esure that you do not create an elec-
trostatic charge, e.g .bywearingsynthetic
clothin gorasar esult of frictio nonfabrics.
Therefore, you should not pull or slide the
battery over carpet sorother synthetic
materials. R
never touc hthe battery first. To discharge
ap ossible electrostatic charge, step out of
th ev ehicle firs tand touc hthe bodywork.
R do not wipe th ebattery using acloth. The
battery may explode as aresult of electro-
static charge or due to flyin gsparks.
! Before loosening th eterminal clamps of
th eb attery, switch off th eengine and
remove th ekey or, on vehicles with KEY-
LESS-GO*, mak esure that th eignitio nis
not switche don. In th einstrumen tcluster,
all of th eindicator lamps must be out. Oth-
erwise ,you may destroy electronic compo-
nents ,such as th ealternator.
i Mercedes-Ben zrecommend sthaty ou
have work involvin gthe battery, e.g.
removal, charging and replacement, car-
ried out at aqualified specialist workshop,
e.g .aM ercedes-Ben zServic eCentre.
Installation location of th ebattery Your vehicle is equipped with
abattery in the
engine compartment. It is located on th efront
bulkhead under th efilter box on th eright-
hand side of th evehicle when viewed in the
directio noftravel. 0046
Battery
0047 Positive terminal
008A Negative terminal
0088 Breather hose 274
BatteryPractical advice
*o
ptional
207_AKB; 2; 3, en-GB
mkalafa,
Version: 2.11.8.1 2009-07-23T10:23:49+02:00-Seite2 74

i
Remove th ekeyif you park th evehicle
and do no trequire any electrical consum-
ers .The vehicl ewill then use ver ylittle
energy, thus conservin gthe battery.
i If th ebattery is discharged, you mus tuse
th ee mergenc ykey elemen ttounlockthe
vehicle. Disconnecting th
ebattery G
Ris
kofa ccident
If th ebattery is disconnected:
R theb rak eboostin geffec twill no tbea vail-
able. Greate rbrakin gforce will then be
require dand brak epedal travel will be lon-
ger .Ifn eces sary, depress th ebrak epedal
wit hm aximum force.
R thet ransmission is locke dinposition Pon
vehicles wit hautomati ctransmission*
! Always disconnect th ebattery in the
order described below. Never mix up the
terminal clam pdisconnection/connection
order and never mix up th eterminal
clamps. You may otherwise damag ethe
vehicl eelectronics.
X Firmly depress th eparkin gbrak eand on
vehicles wit hautomatic transmission*,
shift th etransmission to position P.
X Switc hoff all electrical consumer s(e.g.
radio, blower, etc.).
X Turn th ekeyto0(Y page 65 )inthe ignition
lock and remove it or make sure tha tno
ignition positio nhasbeen selecte dwith
KEYLESS GO *.In the instrument cluster, all
of the indicator lampsm ust be out.
X Open the bonnet. X
Release clamps 0047on filter box 0046.
X Remove filter box 0046.
X Remove the negative terminal clamp from
the battery.
X Remove the cover from the positive termi-
nal clamp.
X Remove the positive terminal clamp from
the battery.
X Disconnect the breather hose. Removing the battery
X Disconnect the battery ( Ypage 275).
X Loosen the bolt which holds the battery in
place.
X Remove the battery. Charging and fitting the battery
G
Risk of injury
Battery acid is caustic. Avoid contact with the
skin, eyesorc lothing.
Charging the battery G
Risk of injury
Only charge the battery in awell-ventilated
area.Ast he battery is being charged, gases
can escape and generate minor explosions.
This could injure you and other persons or
cause damage to the paintwork or acid cor-
rosion on the vehicle. Battery
275Practical advice
*optional
207_AKB; 2; 3, en-GB
mkalafa
,V ersion: 2.11.8.1
2009-07-23T10:23:49+02:00
-Seite 275 Z