tow MERCEDES-BENZ E-CLASS COUPE 2009 Repair Manual

If
ap ressure of 1. 8bar is not reached
after fiv eminutes:
X Switch off and disconnect th eelectric air
pump and driv ethe vehicle forwards or
backwards approximately 10 m.
This distributes th eTIREFI Tmoree venly.
X Pump up th etyrea gain. G
Ris
kofa ccident
If ap ressur eof1.8bar is no tachieve dafter
fiv em inutes, th etyreist oobadly damaged.
Do no tdrivea ny further. Consult aqualified
specialist worksho pwhichh as th enecessary
specialist knowledge and tools to carry out
th ew ork required .Mercedes-Ben zrecom-
mends that you use aMercedes-Ben zService
Centr efor this purpose. In particular, work
relevan ttosafety or on safety-related sys-
tems must be carried out at aqualified spe-
cialist workshop.
When atyrep ressure of at leas t1.8bar
is reached:
X Press on/off switch 0088on th eelectric air
pump to 0.
The electric air pump is switched off.
X Remove th eTIREFI Tkit from th ewheel.
! Afte ruse, exces sTIREFI Tmay run out of
th ef ille rhose. This may caus estains.
Therefore, plac ethe fille rhoseint heplastic
whic hcontai nedt he TIREFI Tkit.
X Stow away th eTIREFI Tkit,t he electric air
pump and th ewarning triangle.
X Pul lawa yimm ediately.
X Stop after driving for approximately ten
minute sand check th etyrep ressur ewith
th ee lectric air pump. G
Ris
kofa ccident
If th etyrep ressur eisnowlower than 1. 3bar,
th et yreist oobadly damaged. Do no tdrive
any further. Consult aqualified specialist
worksho pwhichh as th enecessary specialist
knowledge and tools to carry out th ework required
.Mercedes-Ben zrecommends that
you use aMercedes-Ben zServic eCentr efor
this purpose. In particular, work relevan tto
safety or on safety-related systems must be
carried out at aqualified specialist workshop.
X If th etyrep ressur eisstill at least 1. 3bar,
correct it (see fuel fille rflap for values).
To increase th etyrep ressure: switch on
th ee lectric air pump.
To reduce th etyrep ressure: open pres-
sure release screw 0071on pressure
gauge 0072.
X Drive to th eneares tworksho pand have the
tyr ec hanged there.
X Hav ethe TIREFI Tkit replace dassoonas
possible at aqualified specialist workshop,
e.g. at aMercedes-Ben zServic eCentre. G
Ris
kofa ccident
Do no texcee dt he maximum spee dof
80 km/h.
The "max .80km/h" label must be affixe din
th ed river' sfieldofv ision.
The vehicle's handlin gcharacteristic smay be
affected. H
Environmental note
Hav ethe used TIREFI Tkit disposed of profes-
sionally, e.g. at aMercedes-Ben zService
Centre.
X Hav ethe TIREFI Tkit replace devery four
years at aqualified specialist workshop,
e.g. aMercedes-Ben zServic eCentre. 266
Flat tyrePractical advice
207_AKB
;2;3,en-GB
mkalafa ,V ersion: 2.11.8.1
2009-07-23T10:23:49+02:00
-Seite 266

When
atyre pressure of at leas t1.8 bar
is reached:
X Press on/off switch 008Aon the electric air
pump to 0.
The electric air pump is switched off.
X Remove the TIREFIT kit from the wheel.
! After use,e xcess TIREFIT may run out of
the filler hose. This may caus estains.
Therefore, place the filler hose in the plastic
which contained the TIREFIT kit.
X Stow away the TIREFIT kit, the electric air
pump and the warning triangle.
X Pull away immediately.
X Stop after driving for approximately ten
minutes and check the tyre pressure with
the electric air pump. G
Risk of accident
If the tyre pressure is now lower than 1.3 bar,
the tyre is too badly damaged. Do not drive
any further. Consult aqualified specialist
worksho pwhich has the necessary specialist
knowledge and tools to carry out the work
required .Mercedes-Benz recommends that
you use aMercedes-Benz Service Centre for
this purpose. In particular, work relevant to
safety or on safety-related systems must be
carrie dout at aqualified specialist workshop. X
If the tyre pressure is still at least 1.3 bar,
correct it (see fuel filler flap for values).
To increase the tyre pressure: switch on
the electric air pump. To reduce the tyre pressure:
press pres-
sure release button 0070next to pressure
gauge 0071.
X Drive to the neares tworksho pand have the
tyre changed there.
X Have the TIREFIT kit replaced as soon as
possible at aqualified specialist workshop,
e.g. at aMercedes-Benz Service Centre. G
Risk of accident
Do not exceed the maximu mspee dof
80 km/h.
The "max. 80 km/h" label must be affixe din
the driver's fiel dofvision.
The vehicle's handling characteristics may be
affected. H
Environmental note
Have the use dTIREFIT kit disposed of profes-
sionally ,e.g. at aMercedes-Benz Service
Centre.
X Have the TIREFIT kit replaced every four
years at aqualified specialist workshop,
e.g. aMercedes-Benz Service Centre. Changing
awheel and fitting the
spare wheel* G
Risk of accident
The whee ldimensions and tyre size of the
"Minispare" emergency spare wheel* may dif-
fer from those of the damaged wheel.
You rvehicle's handling characteristics will
change when a"Minispare" emergency spare
wheel* is fitted. Adapt you rstyle of driving
accordingly.
The "Minispare" emergency spare wheel*
may only be use dfor as hort time. Do not
exceed the maximu mspee dof80k m/h and
do not deactivate ESP ®
.
Never drive the vehicl ewith more than one
"Minispare" emergency spare wheel* fitted. 268
Flat tyrePractical advice
*o
ptional
207_AKB; 2; 3, en-GB
mkalafa,
Version: 2.11.8.1 2009-07-23T10:23:49+02:00-Seite 268

G
Risk of accident
Have the collapsible emergency spare
wheel *replaced with anew wheel as soon as
possible at aqualified specialist workshop
which has the necessary specialist knowledge
and tools to carry out the work required.
Mercedes-Benz recommends that you use a
Mercedes-Benz Service Centr efor this pur-
pose. In particular, work relevant to safety or
on safety-related systems must be carried out
at aq ualified specialist workshop.
Preparing the vehicle i
Vehicles without aspare wheel* are not
equipped with wheel-changing tools at the
factory. For more information on which
tools are required to perform awheel
change on your vehicle, e.g. wheel chock,
centring pin or wheel wrench, consult a
Mercedes-Benz Service Centre.
X Prepare the vehicle as described
(Y page 263).
X Ifat railer is coupled to the vehicle, uncou-
ple it.
X Brin gthe wheels into the straight-ahead
position.
X Remove the following items from the stow-
age well under the boot floor:
R
the "Minispare" emergency spare
wheel*
R the vehicle tool kit
R the folding wheel chock
R the jack
Use the folding wheel choc ktopreventthe
vehicle from rolling away. X
Fold both plates 0046upwards.
X Fold out lower plate 0047.
X Guide the lugs on the lower plate fully into
opening sinbase plate 008A. Securin
gthe vehicle on level ground
X On level ground: place the folding wheel
choc kora similar item under the wheel that
is diagonally opposite to the wheel you wish
to change. Securin
gthe vehicle on slight downhill gradients Flat tyre
269Practical advice
*optional
207_AKB
;2;3,en-GB
mkalafa, Version:2.11.8.1
2009-07-23T10:23:49+02:00
-Seite 269 Z

X
On downhill gradients: place the folding
wheel choc korasimilar item behind the
wheels of the fron tand rear axle. X
Using wheel wrench 0088,loosen the bolts on
the wheel you wish to change by about one
full turn .Donot unscrew the wheel bolts
completely.
Raising the vehicle G
Risk of injury
The jack is designed only to raise the vehicle
for ashort time while awheel is being
changed.
The vehicle must be placed on stands if you
inten dtow ork under it.
Make sure that the jack is placed on afirm,
non-slip, level surface. Do not use wooden
blocks or similar objects as ajack underlay.
The vehicle could otherwise slip off the jack
and seriously injure you.
Do not start the engine at any time while the
wheel is being changed.
Do not lie under the vehicle when it is being
supported by the jack .Ifyou do not raise the
vehicle as described, it could slip off the jack
(e.g. if the engine is started or adoor or the
boot lid is opened or closed) and seriously
injure you. G
Risk of accident
If you fail to position the jack correctly, the
vehicle may: R
slip off the jack
R injure you or others
R be damaged.
Thus, it is important to make sure that the jack
is positioned correctly in the respective jack-
ing points .Befor epositioning the jack,
remove any dirt that may have collected in the
jacking points.
The jacking point sfor the jack are located
behind the wheel housings of the fron twheels
and in fron tofthe wheel housings of the rear
wheels (arrows). Vehicles with AMG equipment:
the vehicle
has cover sfitted to protec tthe vehicle body
nexttot he jacking point sonthe outer sills. Vehicles with AMG equipment*
0046
Cover
X Vehicles with AMG equipment*: fold
cover 0046upwards. 270
Flat tyrePractical advice
*o
ptional
207_AKB; 2; 3, en-GB
mkalafa,
Version:2.11.8.1
2009-07-23T10:23:49+02:00
-Seite 270

X
Place the emergenc yspare wheel ontot he
centring pin and push it on. X
Tighten the wheel bolts until they are fin-
ger-tight.
X Unscrew the centring pin.
X Tighten the last wheel bolt until it is finger-
tight.
Lowering the vehicle X
Lower the vehicle. To do this, turn the crank
of the jack anti-clockwise until the vehicle
is once again standin gfirmly on the ground.
X Place the jack to one side. X
Tighten the wheel bolts evenly in across-
wise patter ninthe sequence indica-
ted (0046 to0086). The tightening torque is
130 Nm. G
Risk of accident
Have the tightening torque checked immedi-
ately after awheel is changed. The wheels
could work loose if they are not tightened to
at orque of 130 Nm.
X Turn the jack back to its initial position and
store it together with the rest of the vehicle
tool kit in the stowage well under the boot
floor.
Vehicles with the "Minispare" emergency
spare wheel*:
X Transport the faulty wheel in the boot.
i When you are driving with the "Minispare"
emergenc yspare wheel* fitted, the tyre
pressure loss warning system* cannot
function reliably. MOExtended run-flat system*
The MOExtended run-flat system may only be
used in conjunction with the activated tyre
pressure loss warning system.
! The maximum permissible distanc ewhich
can be driven in run-flat mode depends on
the load in the vehicle. It is 80 km if the
vehicle is partially laden and 30 km if fully
laden. 272
Flat tyrePractical advice
*o
ptional
207_AKB; 2; 3, en-GB
mkalafa,
Version: 2.11.8.1 2009-07-23T10:23:49+02:00-Seite 272

Towin
gand tow-starting Points to remember
G
Ris
kofa ccident
If yo uhavet he vehicl etowed ,you must us ea
rigid towing ba rif:
R the engine is not running.
R there is abrake system malfunction.
R there is amalfunctio ninthe powe rsupply
or the vehicle's electrical system.
The powe rsteerin gand the brake force boos-
ter do not work when the engine is not run-
ning .Greate rbraking force will the nbe
required and brake peda ltravel will be longer.
If necessary ,dep ress the brake peda lwithf ull
force.
Before towing away ,makes uret ha tthe steer-
ing can be moved and is not locked.
If yo utow or tow-start anothe rvehicle, its
weight must not exceed the maximum per-
missibl egross vehicl eweigh tofy ourvehicle. G
Ris
kofa ccident
The vehicl eisbraked when the HOLD function
or DISTRONI CPLUS* is activated .Therefore,
deactivate HOLD and DISTRONI CPLUSift he
vehicl eistobet owed.
It is better to have the vehicl etransported
tha ntoh aveitt owed.
When towing ,obs erve the lega lrequirements
in al lcountrie sconcerned.
! When towing ,pulla wa yslowly and
smoothly. If the tractiv epower is too high,
the vehicles could be damaged.
! Do not us ethe towing ey efor recovery,
as thi scould damage the vehicle. If in
doubt, recover the vehicl ewithac rane.
! Youm aytow the vehicl efor am aximum
of 50 km. Atowing spee dof50k m/h must
not be exceeded.
For towing distances ove r50km, the entire
vehicl emustbel ifted up and transported. !
On vehicles with KEYLESS-GO *, usethe
key instea dofthe Start/Stop button. Turn
the key to position 2in the ignition lock and
shift the automatic transmission to N.Then
tur nthe key back to 0and leav eitinthe
ignition lock.
! Onlysecur ethe tow cable or towing bar
to the towing eyes .You could otherwise
damage the vehicle.
R Vehicle swithana utomatic transmission*
must not be tow-started.
R If yo uaretowing the vehicl eoveral onger
distance, thi smustbed onew itht he rear
axl eraised.
R Th eign ition must be switched off if yo uare
towing the vehicl ewitht he rea raxler aised.
Otherwise, interventio nbyESP®
could
damage the brake system.
R If the vehicl ehassuffered transmission
damage ,onlyt ow it with the propeller shaft
disconnected.
R If the engine does not start, try jump-start-
ing it (Y page 276).
R If it is not possibl etojump-star tthe vehicle,
have it towed to the neares tqualified spe-
cialist workshop ,e.g.aM ercedes-Benz
Service Centre.
R Th ea utomatic transmission* must be in
position Nwhen the vehicl eisbeing towed.
R Before towing the vehicle, make sure that
the battery is connected and charged. Oth-
erwise:
-yo uc annot switch on the ignition.
- yo uc annot shift the transmission to posi-
tion Non vehicles with automatic trans-
mission*.
- yo uh avenos upport when braking.
i Switch off the automatic locking feature
befor ethe vehicl eistowed (Y page 120).
Otherwise, yo ucould be locked ou twhen
pushing or towing the vehicle. 278
Towin
gand tow-startingPractical advice
*optional
207_AKB; 2; 3, en-GB
mkalafa
,V ersion: 2.11.8.1
2009-07-23T10:23:49+02:00
-Seite 278

Fitting th
etowing eye
Vehicles with atraile rtow hitch*: if you
inten dtou se thevehicl efor towing, fol dout
th eb all couplin gand connec tthe towbar
(Y page 193) to this.
Opening th ecovers The mounting
sfor th eremovable towin geyes
are locate dinthebumpers .They are located
at th efront and rear behind covers. Coupé (example)
X
Press cover 0046inwards on th emarkin gin
th ed irection of th earrow.
X Tak ecover 0046 off th eopening but do not
remove it.
Securing th etowing eye X
Tak ethe towin geye and th ewheel wrench
from th evehicl etoolkit (Y page 207).
X Screw in th etow inge ye clockwise to the
stop.
X Inser tthe wheel wrench handle int othe
towin geye and tighten it. Towing th
evehicle
! You may to wthe vehicl efor am aximum
of 50 km .Atowings pee dof50k m/hm ust
no tbee xceeded.
Fo rtow ingd istances ove r50km,thee ntire
vehicl emust be lifted up and transported.
! The engin emust be switched off (key in
ignition loc kinposition 0or position 1)if
th ev ehicl eisb eingtow ed wit hthe front
axle raised or if th eparking brak eisbeing
tested on adynamometer. Otherwise,
intervention by ESP ®
could damag ethe
brak esystem.
Vehicles with manua ltra nsmission X
Turn th ekeyto position 2(Y page 65 )in
th ei gnition lock.
X Fully depress th eclutch pedal.
X Shift to neutral.
Vehicles with automatic transmission* X
Turn th ekeyto position 2(Y page 65 )in
th ei gnition lock.
X Shift th etransmission to position N. Tow-starting (emergency engine
starting)
Pleas enote:
R Vehicles wit hanautomatic transmission*
must no tbetow-started.
R The battery must be connected.
R The engin eand catalyti cconverter must be
cold.
R Avoid repeated and lengthy starting
attempts.
Vehicles with manua ltra nsmission X
Turn th ekeyto position 2(Y page 65 )in
th ei gnition lock.
X Fully depress th eclutch pedal. Towin
gand tow-starting
279Practical advice
*optional
207_AKB
;2;3,en-GB
mkalafa, Version:2.11.8.1
2009-07-23T10:23:49+02:00
-Seite 279 Z

X
Shift to neutral.
X Tow the vehicl eorletit roll.
X Shift to asuitabl egeara nd bring the clutch
peda lups lowly. Do not depress the accel-
erator pedal.
The engine is started. Removin
gthe towin geye
X Take the wheel wrench from the vehicle
tool kit (Y page 207).
X Insert the wheel wrench handl einto the
towing ey eand turn it anti-clockwise.
X Unscre wthe towing eye.
X Replace the cove rand press it unti lit
engages.
X Return the towing ey eand the wheel
wrench to the vehicl etool kit. Transporting the vehicle
The towing eyes or traile rcoupling *can be
used to pull the vehicle onto atraile rort rans-
porter if yo uwishtot ransport it.
! Only secure the vehicle by the wheel sor
wheel rims ,not by parts of the vehicle such
as axl eorsteering components. Otherwise,
the vehicle could be damaged.
Vehicles with manual transmission X
Shif tton eutral.
Vehicles with automati ctransmission* X
Turn the key to position 2(Y page 65) in
the ignition lock.
X Move the transmissio ntoposition N. Fuses
Note
sonc hanging fuses
The fuses in your vehicl eserv etoc lose down
faulty circuits. If afuseb lows ,allthe compo-
nents on the circuit and thei rfunctions will
fail.
Blown fuses mus tbereplaced with fuses of
the same rating, which yo ucan recognis eby
the colou rand value .The fus eratings are lis-
ted in the fus ealloc ation chart. AMercedes-
Benz Service Centre will be happy to advise
you. G
Ris
koff ire
Only us efuses that have bee napproved for
Mercedes-Benz vehicles and which have the
correct fus erating for the systems con-
cerned. Do not attempt to repai rorbridge
faulty fuses. Otherwise, acircuit overload
could cause afire .H ave the cause trace dand
rectifie dataq ualified specialist workshop,
e.g. aMercedes-Benz Service Centre.
If the newly inserted fus ealsob lows ,havet he
cause trace dand rectifie dataqualified spe-
cialist workshop, e.g. aMercedes-Benz
Service Centre.
! Only us efuses that have bee napproved
for Mercedes-Benz vehicles and which
have the correct fus erating for the system
concerned. Otherwise, components or sys-
tems could be damaged.
The fuses are locate dinvarious fus eboxes:
R fus eb ox on the driver' ssideoft he dash-
board*
R fus ebox in the engine compartment on the
driver' sside
R fus eb ox in the boo tonthe right-hand side
of the vehicle
Fus eallocatio nchart The fus
ealloc ation chart is locate dwitht he
vehicl etool kit (Y page 207) in the stowage 280
FusesPractical advice
*o
ptional
207_AKB; 2; 3, en-GB
mkalafa
,V ersion: 2.11.8.1
2009-07-23T10:23:49+02:00
-Seite 280

compartment under the luggage compart-
ment floor. Before changing
afuse
X Park the vehicle.
X Switch off al lelectrical consumers.
X Remove the key from the ignition lock. Fus
eboxunde rthe dashboard X
To open: openthe driver' sdoor.
X Pull ou tcover 0046slightl yatthe bottom
008A.
X Pull cover 0046outwards and remove it 0047.
X To close: clipinc over0046at the front.
X Fol dc over 0046inward suntilite ngages.
X Close the driver' sdoor. Fus
eboxin the engine compartment
X Make sure that the windscreen wiper sare
turne doff. G
Risk of injury
Make sure that the windscreen wiper sare
turne doff and the key is pulled ou tofthe igni-
tion lock before yo uopenthe cove rofthe fuse
box. Otherwise, the windscreen wiper sand
the wiper rod sabove the cove rcould be set
in motion. Thi scould lead to yo uorothers
being injured by the wiper rods. X
To open: openthe bonne t(Ypage 180). X
Remove moistur efrom the fus ebox using
ad ry cloth.
X Uncli plines 0047 from the lid.
X Move asid elines 0047.R oute the lines behind
connection 008Ato do this.
X Ope nclamps 0046and unhook the corre-
sponding wire straps at the bottom.
X Lift off the fus ebox cove rtowards the front
of the vehicle.
X To close: check whethe rthe rubber sea lis
positioned correctly in the lid.
X Inser tthe li dinto the bracket at the rea rof
the fus ebox.
X Press the li ddowna nd secure with
clamps 0046.
X Clip lines 0047onto the lid.
X Close the bonne t(Ypage 180). Fus
eboxin the boot
X To open: openthe boot. Fuses
281Practical advice
207_AKB; 2; 3, en-GB
mkalafa,V ersion: 2.11.8.1
2009-07-23T10:23:49+02:00
-Seite 281 Z

Note
sont he technica ldata ............. 284
Genuine Mercedes-Benz parts .........284
Vehicle electronics ...........................284
Vehicle identification plates ............286
Service products and capacities .....287
Vehicle data, E200 CGI BlueEFFI-
CIENCY ............................................... 291
Vehicle data, E250 CGI BlueEFFI-
CIENCY ............................................... 292
Vehicle data, E350 ........................... 292
Vehicle data, E350 CGI BlueEFFI-
CIENCY ............................................... 293
Vehicle data, E500 ........................... 293
Vehicle data, E220 CDI BlueEFFI-
CIENCY ............................................... 294
Vehicle data, E250 CDI BlueEFFI-
CIENCY ............................................... 295
Vehicle data, E350 CDI BlueEFFI-
CIENCY ............................................... 296
Boot lid opening dimensions ...........296
Tyres and wheels .............................. 296
Trailer tow hitch* .............................. 303
24-GHz radar sensor system (coun-
tryo verview) ..................................... 304 283Technical data
207_AKB
;2;3,en-GB
mkalafa, Version:2.11.8.1
2009-07-23T10:23:49+02:0
0-Seite 283