change wheel MERCEDES-BENZ E-CLASS COUPE 2017 Owner's Manual

The tyre pressure loss
warning sy stem does not
re place the need toregularly check the tyre
pressures.
Sy stem limitations
The tyre pressure loss warning sy stem does not
issue a warning:
R Ifth e tyre pressure is set incor rectl y.
R Ifth ere is a sudden pressure loss caused, for
ex ample, byafo re ign object penetrating the
tyre.
R Ifth e pressure loss in se veral tyres decrea‐
ses at the same rate.
The tyre pressure loss warning sy stem has a
limited or dela yed function:
R When thero ad sur face is poo r,e.g. snow or
gr ave l.
R When driving with snow chains.
R When driving in a very sporty driving style
with high cornering speeds or sudden accel‐
eration.
R When towing a very heavy or large trailer.
R When driving with a high load. Be sure
toalso obse rveth efo llowing fur ther
re lated subjects:
R Display messages about the tyres
(→ page 459)
R Notes on tyre pressure (→ page 389)
Re starting the ty repressure loss warning
sy stem
Re quirement:
R The recommended tyre pressure is cor rectly
set forth ere spective operating condition on
each of thefo ur wheels (→ page 389).
On-board co mputer:
, Service .
Tyre pressure
The Run Flat Indicator active Restart with OK
message is shown in the multifunction displa y.
Re start the tyre pressure loss warning sy stem in
th efo llowing situations:
R The tyre pressure has changed.
R The wheels or tyres ha vebeen changed or
newly fitted. #
Press atobegin the new start.
The Tyre pressure now OK? message is
shown in the multifunction displa y. #
Select Yes. #
Press atoconfirm there start.
The Run Flat Indicator restarted message is
shown in the multifunction displa y.
Af teryo u ha vedriven for a few minutes, the
tyre pressu reloss warning sy stem monitors
th e set tyre pressures of all the tyres.
Be sure toalso obse rveth efo llowing fur ther
re lated subjects:
R Notes on tyre pressure (→ page 389) Wheel
change Note
s on selecting, fitting and replacing
tyres Yo
u can ask for information rega rding permit ted
wheel/tyre combinations at a Mercedes-Benz
Service Cent re. 396
Wheels and tyres

*
NO
TERisk todriving saf ety from retrea‐
ded tyres Re
treaded tyres are nei ther tested nor rec‐
ommended byMercedes-Benz, since pr evi‐
ous damage cannot alw ays be de tected on
re treaded tyres.
Fo rth is reason driving saf ety cannot be guar‐
anteed. #
Do not use used tyres if you ha veno
information about their pr evious usage. *
NO
TEPossible damage towheels or
tyres when driving over obs tacles Lar
gewheels ha vea lo wer tyre section width.
The lo werth e tyre section width, the greater
is therisk of damage towheels or tyres when
driving over obs tacles. #
Avoid obs tacles or drive pa rticular ly
carefully. *
NO
TEDama getoelectronic component
parts from the use of tyre-fitting tools Ve
hicles with a tyre pressure monitoring
sy stem: electronic component parts are
located in the wheel. Tyre-fitting tools should
not be applied in the area of theva lve.
The tools could damage the electronic com‐
ponent parts. #
Have the tyres changed at a qualified
specialist workshop onl y. *
NO
TEDama getosummer tyres at low
ambient temp eratures Using summer tyres at
very low ambient
te mp eratures can cause crac kstoform,
th ereby damaging the tyres permanentl y. #
Attemp eratures below 7 °C use M+S-
tyres. Ac
cessory pa rts th at are not appr ovedfo ryo ur
ve hicle byMercedes-Benz or are not being used
cor rectly can impair the operating saf ety. Before pu
rchasing and using non-appr oved
accesso ries, visit a qualified specialist workshop
and enquire about:
R Suitability
R Legal stipulations
R Factory recommendations &
WARNING Risk of accident wi thhigh
per form ance tyres
The special tyre tread in combination with
th e optimised tyre compound, means that
th erisk of skidding or hydroplaning on wet
ro ads is inc reased.
In addition, the tyre grip is greatly reduced at
a low outside temp erature and tyre running
te mp erature. #
Switch on the ESP ®
and adapt your
driving style accordingly. #
Use M+S tyres at outside temp eratures
of less than 50 °F. 398
Wheels and tyres

may se
verely impair the driving characteris‐
tics.
The disk brakes or wheel suspension compo‐
nents may also be damaged. #
Rotate front and rear wheels on lyifthe
wheels and tyres are of the same
dimensions. Inter
changing the front and rear wheels if the
wheels or tyres ha vediffere nt dimensions can
re nder thege neral operating pe rmit in valid.
The wear pat tern s on the front and rear wheels
dif fer:
R Front wheels wear more on the shoulder of
th e tyre
R Rear wheels wear more in the cent reofthe
tyre
On vehicles with the same front and rear wheel
size, you can inter change the wheels every
5000 to10000 km, depending on thewe ar.
Ensure the direction of rotation is maintained for
th e wheels. It is imperative
toobser vethe instructions and
saf ety no tes on "Wheel change" when doing so. Note
s onstoring wheels R
Afterre moving wheels, store them in a cool,
dry and preferably dark place.
R Protect the tyres from conta ct withoil,
grease or fuel. Overview of
the ty re-change tool kit Apart from some countr
y-specific variants, vehi‐
cles are not equipped with a tyre-change tool kit.
Fo r more information on which tyre-changing
to ols are requ ired and appr ovedfo r per form ing a
wheel change on your vehicle, consult a qualified
specialist workshop.
Necessary tyre-changing tools may include, for
ex ample:
R Jack
R Chock
R Wheel spanner
R Cent ring pin %
The jack weighs appr oximately 3.4 kg.
The maximum load capacity of the jack can
be found on thest icke r af fixe dto the jac k.
The jack is maintenance-free. If there is a
malfunction, please conta ct aqualified spe‐
cialist workshop.
The tyre-change tool kit is located in tool bag
1. 1
Tool bag
To ol bag 1contains:
R Jack
R Gloves
R Wheel spanner 400
Wheels and tyres

R
Centring pin
R Folding wheel chock
R Ratchet for jack
Setting up thefo lding wheel chock Prepa
ring theve hicle for a wheel change Re
quirements:
R The requ ired tyre-change tool kit is available.
If yo ur vehicle is not equipped with the tyre-
ch ange tool kit, consult a qualified specialist
wo rkshop tofind out about suitable tools.
R The vehicle is not on a slope.
R The vehicle is on solid, non-slippery and le vel
ground. #
Apply the electric parking brake manually. #
Movethe front wheels tothest ra ight-ahead
position. #
Vehicles with manual transmission:
Engage firs t or reve rsege ar. #
Vehicles with automatic transmission:
Shift into position j. #
Vehicles with AIR BODY CONT ROL:Set the
normal vehicle le vel (→ page 196). #
Switch off the engine. #
Make sure that the engine cann otbe star ted. #
Place choc ks orother suitable items under
th e front and rear of the wheel that is diago‐
nally opposite the wheel you wish tochange. #
Remo vethe hub caps if necessary
(→ page 401). #
Raise theve hicle (→ page 402). Re
moving and fitting hub caps Re
quirement:
R The vehicle is prepared for a wheel change
(→ page 401).
Pla stic hub cap #
Toremo ve:turn the cent recover of the hub
cap anti-clockwise and remo vethe hub cap. #
Tofit: make sure that the cent recover of the
hub cap is turned anti-clockwise. #
Position the hub cap and turn the cent re
co ver clockwise until the hub cap engages
ph ysically and audibly. Wheels and tyres
401

Aluminium hub cap
#
Toremo ve:position soc ket2 on hub cap
1.
% The soc ket can be found in the tyre-change
to ol kit. #
Position wheel spanner 3on soc ket2. #
Using wheel spanner 3, turn hub cap1
anti-clo ckwise and remo veit. #
Tofit: position hub cap 1and turn until it is
comple tely flush with the wheel. #
Position soc ket2 on hub cap 1. #
Attach wheel spanner 3tosoc ket2 and
tighten the hub cap clockwise.
Specified tightening torq ue: 25 Nm. #
Raise theve hicle (→ page 402). Ra
ising theve hicle when changing a wheel Re
quirements:
R There are no persons in theve hicle.
R The vehicle is prepared for a wheel change
(→ page 401).
R The hub caps ha vebeen remo ved
( → page 401).
Impor tant no tes on using the jack:
R Only use theve hicle-specific jack that has
been tested and appr ovedby Mercedes-Benz
to raise theve hicle.
R The jack is only designed forra ising and
holding theve hicle for a short time while a
wheel is being changed and not for mainte‐
nance workunder theve hicle. R
The jack must be placed on a firm ,fl at and
non-slip sur face. If necessar y,use a lar ge,
load-bearing, non-slip underla y.
R The base of the jack must be positioned ver‐
tically under the jack support point. Ru
les of conduct when theve hicle is raised:
R Never place your hands or feet under the
ve hicle.
R Do not lie under theve hicle.
R Do not start the engine and do not release
th e electric parking brake.
R Do not open or close any doors or the boot
lid. 402
Wheels and tyres

#
Using the wheel spanner, loosen the wheel
bolts on the wheel you wish tochange by
about one full turn. Do not unscr ewthe
scr ews comple tely. Po
sition of jack support points &
WARNING Risk of inju ryfrom incor rect
positioning of the jack
If yo u do not position the jack cor rectly at
th e appropriate jacking point of theve hicle,
th e jack could tip with theve hicle raised. #
Only position the jack at the appropri‐
ate jacking point of theve hicle. The
base of the jack must be positioned ver‐
tically under the jacking point of the
ve hicle. *
NO
TEVehicle damage from the jack If
yo u do not position the jack cor rectly at
th e appropriate jack support point of the
ve hicle, the jack could tip over with theve hi‐
cle raised. #
The jack is designed exclusively for
jacking up theve hicle at the jack sup‐
port points. #
Take thera tchet ring spanner out of the tyre-
ch ange tool kit and place it on the he xagon
nut of the jack so that the letters AUF are
visible. Wheels and tyres
403

&
WARNING Risk of accident from losing a
wheel
Oiled, greased or damaged wheel bolt/wheel
nut thre ads or wheel hub/wheel mounting
bolt thre ads can cause the wheel bolts/
wheel nuts tocome loose.
As a result, you could lose a wheel while driv‐
ing. #
Never oil or grease theth re ads. #
Intheeve nt of damage totheth re ads,
con tact a qualified specialist workshop
immediatel y. #
Have the damaged wheel bolts or dam‐
aged hub thre ads replaced. #
Do not continue driving. #
Obser vethe information on thech oice of
tyres (→ page 396).
Fo r tyres with a specified direction of rotation,
an ar rowonthe side wall of the tyre indicates
th e cor rect di rection of rotation. Obse rvethe
direction of rotation when fitting. #
Slide the wheel tobe mounted onto the cen‐
tring pin and push it on. &
WARNING Risk of inju ryfrom tightening
wheel bolts andnuts
If yo u tighten the wheel bolts or wheel nuts
when theve hicle is raised, the jack could tip. #
Only tighten wheel bolts or wheel nuts
when theve hicle is on the ground. #
For saf etyre asons, Mercedes-Benz recom‐
mends that you on lyuse wheel bolts which
ha ve been appr oved for Mercedes-Benz vehi‐
cles, as well as forth e wheel in question. #
Tighten the wheel bolts until they are finger-
tight. #
Unscr ew the cent ring pin. #
Tighten the last wheel bolt until it is finger-
tight. #
Lowe rth eve hicle (→ page 405). Lo
weri ngtheve hicle af ter a wheel change Re
quirement:
R The new wheel has been fitted (→ page 404). #
Place thera tchet ring spanner onto the he xa‐
gon nut of the jack so that the letters "AB"
are visible. #
Tolowe r the vehicle: turnthera tchet ring
spanner of the jack anti-clockwise. #
Tighten the wheel bolts evenly in a crosswise
pattern in the sequence indicated (1 to5 ).
Specified tightening torq ue: 150 Nm. Wheels and tyres
405

Brake
forc e distribution
EBD (Elect ronic Brake forc e Distribu‐
tion) ..................................................... 174
Brakes ABS (Anti-lock Braking Sy stem) ........... 17 0
Ad aptive brake lights .......................... .180
BA S (Brake Assi stSystem) .................. 17 0
Driving tips .......................................... 14 4
EBD (Electronic Brake forc e Distribu‐
tion) ..................................................... 174
HOLD function .................................... .193
Limi ted braking ef fect (salt-trea ted
ro ads) .................................................. 14 4
New/replaced brake linings/brake
discs .................................................... 14 3
Ru nning-in no tes ..................................1 43
Brakes see Active Brake Assi st
Braking assistance see BAS (Brake Assi stSystem)
Breakdown ............................................... 369
Assis tance overview .............................. 16
To w- starting ........................................ 384
To wing away ........................................ 380 Tr
ansporting theve hicle ......................3 82
Wheel change ...................................... 401
Breakdown assistance call see Service call
Breakdown management see Service call
Bu rm ester ®
high-end 3D sur round
sound sy stem
Ad justing the balance/fader ............... 350
Ad justing the sound optimisation ........ 351
Ad justing treble, mid and bass ............ 350
Calling up the sound menu .................. 350
Information .......................................... 350
Setting the sound profile ..................... 351
Burmes ter®
sur round sound sy stem .....3 49
Ad justing the balance/fader ............... 350
Ad justing the sound focus ................... 350
Ad justing treble, mid and bass ............ 350
Calling up the sound menu .................. 349
Information .......................................... 349
Switching the sur round sound on/off
............................................................ .350
Buttons Steering wheel .................................... 235 C
CA module (TV) ........................................ 349
Calling up a menu ................................ 349
Inse rting .............................................. 348
Call list Making a call ...................................... .304
Options in the call list .......................... 304
Overview ............................................. 304
Calling up the sound menu
Burmes ter®
high-end 3D sur round
sound sy stem ...................................... 350
Burmes ter®
sur round sound sy stem ... 349
Calls ..........................................................3 00
Ac cepting ............................................ 300
Ac tivating functions du ring a call ......... 301
Calls wi thseveral participants ............ .301
Declining ............................................. 300
Ending a call ........................................ 300
Incoming call du ring an existing call .... 301
Making ................................................ 300
Vi ath eove rhead control panel
(Mercedes me connect) ....................... 314
Camera see 360° Camera Index
501

_Before
starting the engine, turn
th esteering wheel. .............................. 472
Blind Spot Assi stcur rently una vaila‐
ble See Owner's Manual ......................444
Blind Spot Assi stinope rative ............... 445
Blind Spot Assi stnot available when
to wing a trailer See Owner's Manual ...4 45
Brake immediate ly............................... 433
ÂChange key bat teries .................. 464
ØCheck AdBlue See Owne r’s
Manual ................................................ 457
JCheck brake fluid le vel................ 433
4Check eng. oil le v.when next
re fuelling ............................................. 454
jChe cktrailer hitch lo ck............... 467
hCheck tyre(s) ............................... 460
!Clean the fuel filter ...................... 457
Clutch overheated Avoid pulling away
fo r XX:XX mins ..................................... 470
É Compressor is cooling ................442?
Coolant Stop vehicle Switch
engine off ............................................ 451
Cruise contro l and Limiter inope ra‐
tive ...................................................... 449
Cruise cont rol inope rative ................... 449
Cruise cont rol off ................................ 449
! currently una vailable See Own‐
er's Manual ........................................ .425
÷cur rently una vailable See Own‐
er's Manual ........................................ .426
Depress clutch ful lyto start engine .....4 70
Dis tance Pilot available again ..............447
Dis tance Pilot cur rently una vailable
See Owner's Manual ...........................448
Dis tance Pilot inope rative ................... 448
È .................................................... 449
Ø Eng.start not possible in XXX
mi ........................................................ 458
ØEng. start not possible ................ 458 5Engine oil le
vel cannot be
measured ............................................ 456
4Engine oil le velRe duce oil le vel...4 55
4Engine oil le velSt op vehicle
Switch engine off ................................ 454
4Engine oil pressure Stop Switch
off engine ............................................ 456
6Example: Front left malfunction
Consult workshop ...............................4 37
b Example: Left dipped beam ........478
6 Example: Left windowbag mal‐
function Consult workshop ................. 437
Example: Parking Pilot Parking can‐
celled ................................................ .446
_Example: Rear left seat back‐
re st not lo cked .................................... 477
Fr ont-passenger airbag disabled See
Owner's Manual ..................................4 38
Fr ont-passenger airbag enabled See
Owner's Manual ..................................4 39506
Index

Emer
gency key
Locking a door ....................................... 67
Un locking a door .................................. .67
Emer gency key element
Inserting/removing ............................... 60
Emer gency operation mode
St arting vehicle ................................... 14 2
Emer gency spare wheel
No tes .................................................. 406
Re moving ............................................ 407
Emer gency spare wheel
see Spare wheel
see Wheel change
Energy consu mption
Ke y ........................................................ 59
Engine ECO start/ stop function ......................1 46
Engine number ..................................... 41 0
St arting (eme rgency operation
mode) .................................................. 14 2
St arting (mobile phone) ...................... .141
St arting (s tart/s top button) .................1 41
St arting assis tance .............................. 377
Switching off (s tart/s top button) ........ 16 0Engine bonnet
Function (active bonnet) ...................... 353
Opening/closing ................................. 354
Re setting (active bonnet) .................... 353
Engine data Displaying ............................................ 14 9
Engine electronics Notes .................................................. 408
Engine number ......................................... 41 0
Engine oil ................................................ .357
Ad ditives .............................................. 416
Checking the oil le vel using the oil
dipstick ............................................... 356
Checking the oil le vel using the on-
board computer ................................... 356
Filling capacity .....................................4 17
MB-F reigabe or MB-Appr oval .............. .417
To pping up ...........................................3 57
Entering characters
Fu nction/no tes ................................... 264
On theto uchpad ................................ .265
Using the controller ............................. 265
ERA-GLONASS test mode
St arting/ending .................................. .319 ESC (Electronic
Stability Control)
see ESP ®
(Electronic Stability Prog ram)
ESP ®
(Electronic Stability Prog ram) ...... 17 0
Crosswind Assist .................................. 174
Fu nction/no tes ................................... 17 0
Switching on/off .................................. 174
Tr ailer stabilisation .............................. .174
EU type appr oval number ....................... 41 0
Exterior lighting Care .................................................... 363
Exterior lighting see Lights F
Fa tigue warning
see ATTENTION ASSIST
Fa ult message
see Displ aymessa ge
Favo urites
Ad ding .................................................2 62
Calling up ............................................ 262
Deleting ............................................... 263
Moving ................................................ 263 Index
511