MERCEDES-BENZ E-CLASS SALOON 2021 Owners Manual

#
Position support 2of jack 4on jack sup-
port point 1. #
Turn ratchet 3clockwise until support 2
sits comple tely on jack support point 1and
th e base of the jack lies evenly on thegr ound. #
Turn ratchet 3until the tyre is raised a maxi-
mum of 3 cm from thegr ound. #
Loosen and remo vethe wheel (/ page 408). R
R
emo
emo ving a wheel
ving a wheel R R
eq eq uir
uir ements:
ements:
R The vehicle is raised (/ page 406).
* NO
NOTE
TEMercedes-AMG vehicles #
Obser vethe no tes in the Supplement.
Yo u could otherwise failto recognise
dangers. When
changing a wheel, avoid applying any force
to the brake discs, as this could impair the le vel of
comfort when braking.
* N
NOOTE
TE Damage tothre ading from dirt on
wheel bolts #
Do not place wheel bolts in sand or on a
dirty sur face. #
Unscr ewthe uppermost wheel bolt com-
ple tely. #
Screw cent ring pin 1into theth re ad ins tead
of the wheel bolt. #
Unscr ewthere maining wheel bolts com-
ple tely. #
Remo vethe wheel. F F
itting a ne
itting a ne w wheel
w wheel *
N NOOTE TE Mercedes-AMG vehicles #
Obser vethe no tes in the Supplement.
Yo u could otherwise failto recognise
dangers. 408 408
Wheels and tyres

&
W
W ARNI NG
ARNI NGRisk of accident from losing a
wheel
Oiled or greased wheel bolts can cause the
wheel bolts tocome loose, as too can dam-
aged wheel bolts or wheel hub thre ads. #
Never oil or grease theth re ads. #
Intheev ent of damage totheth re ads,
contact a quali/ed specialist workshop
immediatel y. #
Have the damaged wheel bolts or dam-
aged hub thre ads replaced. #
Do not continue driving. #
Obser vethe information on thech oice of tyres
(/ page 400).
Fo r tyres with a speci/ed direction of rotation, an
ar ro w on the side wall of the tyre indicates the
cor rect direction of rotation. Obser vethe direc-
tion of rotation when /tting. #
Slide the wheel tobe mounted onto the cen-
tring pin and push it on. &
W
WARNING
ARNING Risk of injury from tightening
wheel bolts and nuts
If yo u tighten the wheel bolts or wheel nuts
when theve hicle is raised, the jack could tip. #
Only tighten wheel bolts or wheel nuts
when theve hicle is on thegr ound. #
Be sure toobser vethe inst ructions and saf ety
no tes on "Changing a wheel" (/ page 400). #
For saf etyre asons, only use wheel bolts which
ha ve been appr oved byMercedes-Benz and
fo rth e wheel in question. #
Tighten the wheel bolts evenly in a diagonal
pattern in the order indicated until they are
/nger-tight. #
Unscr ewand remo vethe centring pin. #
Tighten the last wheel bolt until it is /n ger-
tight. #
Lowe rth eve hicle (/ page 409). Low Low
er
ering t
ing t he v
he vehicle
ehicle aTer
aTera wheel c
a wheel c hange
hange R
R
eq
eq uir
uir ements:
ements:
R The new wheel has been /tted (/ page 408). #
T
To low
o low er t
er the v
he v ehicle:
ehicle: placethera tchet onto
th e he xagon nut of the jack so that the letters
"AB" are visible and turn anti-clockwise. #
Tighten the wheel bolts evenly in a diagonal
pattern in the order indicated 1to5 with
an initial maximum forc e of 80 Nm. #
Tighten the wheel bolts evenly in a diagonal
pattern in the order indicated 1to5 with
th e speci/ed tightening torque of 150 Nm. Wheels and tyres
409
409

&
W
WARNI NG
ARNI NGRisk of accident due toincor-
re ct tightening torque
The wheels could come loose if the wheel
bolts or wheel nuts are not tightened tothe
prescribed torque. #
Ensure that the wheel bolts or wheel
nuts are tightened tothe prescribed
tightening torque. #
Ifyo u are not sure, do not mo vetheve hi-
cle. Con tact a quali/ed specialist work-
shop and ha vethe tightening torque
ch ecked immediatel y. #
Check the tyre pressure of the ne wly/tted
wheel and adjust it if necessar y.
% The following does not apply if the new wheel
is an emer gency spa rewheel. #
V
Vehicles wit
ehicles wit h tyr
h tyre pr
e pressur
essur e loss w
e loss w ar
arning sy
ning sy s-
s-
t
t em:
em: restart the tyre pressure loss warning
system (/ page 400). #
V
Vehicles wit
ehicles wit h a tyr
h a tyre pr
e pressur
essur e monit
e monit or
oring sy
ing sy s-
s-
t
t em:
em: restart the tyre pressure monitoring sys-
te m (/ page 399). Emerg
Emerg
ency spar
ency spar e wheel
e wheel N
No
ot
tes on t
es on t he emerg
he emerg ency spar
ency spar e wheel
e wheel &
W
WARNING
ARNING Risk of accident caused by
incor rect wheel and tyre dimensions
The wheel or tyre size and the tyre type of the
emer gency spa rewheel or spare wheel and
th e wheel tobe replaced may di.er. The emer-
ge ncy spa rewheel or spare wheel can signi/-
cantly impair driving characteristics of the
ve hicle.
To prev ent hazardous situations: #
Drive carefull y. #
Never /t more than one emer gency
spa rewheel or spare wheel that di.ers
in size. #
Only use an emer gency spa rewheel or
spare wheel brie0y. #
Do not deacti vate ESP ®
. #
Have the emer gency spa rewheel or
spare wheel of a di.erent size replaced
at the nearest quali/ed specialist work- shop. The new wheel must ha
vethe cor-
re ct dimensions. %
The emer gency spa rewheel is secured in the
emer gency spa rewheel bag in the boot.
Obser vethefo llowing no tes on /tting an emer-
ge ncy spa rewheel:
R The maximum permissible speed with an
emer gency spa rewheel /tted is 80 km/h.
R Do not /t the emer gency spa rewheel with
snow chains.
R Replace the emer gency spa rewheel aTer six
ye ars at the latest, rega rdless of wear.
R Check the tyre pressure of the emer gency
spa rewheel /tted. Cor rect the pressure as
necessar y.
% The speci/ed tyre pressure is stated on the
label of the emer gency spa rewheel. 410
410
Wheels and tyres

%
V
V ehicles wit
ehicles wit h a tyr
h a tyre pr
e pressur
essur e loss w
e loss w ar
arning
ning
syst
syst em:
em: if an emer gency spa rewheel is /tted,
th e tyre pressure loss warning system cannot
function reliabl y.Only restart the system
again when the emer gency spa rewheel has
been replaced with a new wheel.
V
V ehicles wit
ehicles wit h a tyr
h a tyre pr
e pressur
essur e monit
e monit or
oring sy
ing sy s-
s-
t
t em:
em: if an emer gency spa rewheel is /tted, the
tyre pressure monitoring system cannot func-
tion reliabl y.Fo r a few minutes aTer an emer-
ge ncy spa rewheel is /tted, the system may
still display the tyre pressure of there mo ved
wheel. Only restart the system again when the
emer gency spa rewheel has been replaced
with a new wheel.
Be sure toalso obser vethefo llowing fur ther rela-
te d subjects:
R Notes on tyre pressure (/ page 396)
R Tyre pressure table (/ page 397)
R Notes on /tting tyres (/ page 400)
R Fitting an emer gency spa rewheel
(/ page 405) Wheels and tyres
411 411

N
N
o
ot
tes on t
es on t ec
echnical data
hnical data
* NO
NOTE
TEMercedes-AMG vehicles #
Obser vethe no tes in the Supplement.
Yo u could otherwise failto recognise
dangers. The
tech nical data was de term ined in accordance
with EU Directives. The data stated only applies to
ve hicles with standard equipment. You can obtain
fur ther information from a Mercedes-Benz Service
Centre.
Onl Onl y f
y for cert
or cert ain countr
ain countr ies:
ies:you can /n dvehicle-
speci/c vehicle data in theCO C documents (CER-
TIFIC ATE OF CONFORMITY). These documents
are deli vered with your vehicle. On-boar
On-boar
d electr
d electronics
onics N
No
ot
tes on t
es on t am
amper
per ing wit
ing wit h t
h the engine electr
he engine electr onics
onics *
N
NOOTE
TE Prematu rewe arthro ugh improper
maintenance Improper maintenance may cause
vehicle
components towe ar more quickly and the
ve hicle's operating permit may be in validated. #
Always ha veworkon the engine elec-
tronics and related components car ried
out at a quali/ed specialist workshop. T
T
w
w o-wa
o-wa y r
y radios
adios N
No
ot
tes on
es on /tting
/tting tw
two-wa
o-wa y r
y radios
adios &
W
WARNING
ARNING Risk of accident due to
improper workon two-w ayradios
If two-w ayradios are manipulated or retro/t-
ted incor rectl y,the electromagnetic radiation
from the two-w ayradios can inter fere with the
ve hicle elect ronics and jeopardise the operat-
ing saf ety of theve hicle. #
You should ha veall workon electrical
and electronic components car ried out
at a quali/ed specialist workshop. &
W
WARNING
ARNING Risk of accident due to
improper operation of two-w ayradios
If yo u use two-w ayradios in theve hicle
improper ly,th eir electromagnetic radiation
can disrupt theve hicle's elect ronics. This is
th e case in thefo llowing situations, in particu-
lar:
R The two-w ayradio is not connected toan
ex terior aerial.
R The exterior aerial is /tted incor rectly or is
not a lo w-re0ection aerial.
This could jeopardise the operating saf ety of
th eve hicle. #
Have the lo w-re0ection exterior aerial /t-
ted at a quali/ed specialist workshop. #
When operating two-w ayradios in the
ve hicle, alw ays connect them tothe lo w-
re 0ection exterior aerial. 412
412
Te
ch nical data

*
N
N O
OTE
TE Inva lidation of the operating permit
due tofailure tocomply with the inst ruc-
tions for installation and use The operating permit may be in
validated if the
inst ructions for installation and use of two-w ay
ra dios are not obser ved. #
Only use appr oved frequency bands. #
Obser vethe maximum permissible out-
put po wer in these frequency bands. #
Only use appr oved aerial positions. 1
Front roof area
2 Rear roof area
3 Rear wings
4 Boot lid
On vehicles with a panoramic sliding sunroof, /t-
ting an aerial tothe front or rear roof area is not
permitted. On
there ar wings, it is recommended that you /t
th e aerial on the side of theve hicle closest tothe
cent reofthero ad.
Use Tech nical Speci/cation ISO/TS 21609 (Road
Ve hicles – "EMCs for installation of aTermar ket
ra dio frequency transmitting equipment") when
re tro/tting two- wayra dios. Comply with the legal
re qu irements for de tach able parts.
If yo ur vehicle has /ttings for two-w ayradio equip-
ment, use the po wer supply and aerial connectors
pr ov ided in the pre-ins tallation. Obser vethe man-
ufacturer's supplements when /tting.
T
T w
w o-wa
o-wa y r
y radio tr
adio tr ansmission output
ansmission output
The maximum transmission output (PEAK) at the
base of the aerial must not exceed theva lues in
th efo llowing table. Te
ch nical data
413
413

F
F
r
req
eq uency band and maximum tr
uency band and maximum tr ansmission out-
ansmission out-
put
put F
F
r
req
eq uency band
uency band Maximum tr
Maximum transmis-
ansmis-
sion output
sion output
Short wave
3 - 54 MHz 100 W
4 m frequency band
74 - 88 MHz 30 W
2 m frequency band
144 - 174 MHz 50 W
Te rrestrial Trunked
Ra dio (TETRA)
380 - 460 MHz 10 W
70 cm frequency band
420 - 450 MHz 35 W
Tw o-w ayradio
(2G/3G/4G) 10 W The
following can be used in theve hicle without
re strictions:
R two- wayra dios with a maximum transmission
output of up to100 mW
R RF transmitters with transmitter frequencies in
th e 380 - 410 MHz frequency band and a
maximum transmission output of up to2 W
(TETRA)
R mobile phones (2G/3G/4G)
There are no restrictions when positioning the
aerial on the outside of theve hicle forth efo llo w-
ing frequency bands:
R Terrestrial Trunked Radio (TETRA)
R 70 cm frequency band
R 2G/3G/4G R R
egulat
egulat or
ory r
y r adio
adio identi/cation
identi/cation and not
and notes
es R
R
egulat
egulat or
ory r
y r adio
adio identi/cation
identi/cation of small com
of small compo-
po-
nents
nents Manufacturer information about
radio-based vehi-
cle components can be found using thekey
phrase "Regulatory radio identi/cation" in the Dig- ital Operator's Manual in
theve hicle, on the inter-
net and in the app. R
R
egulat
egulat or
ory r
y r adio
adio identi/cation
identi/cation – Indonesia
– Indonesia Manufacturer information about
radio-based vehi-
cle components can be found using thekey
phrase "Regulatory radio identi/cation – Indone-
sia" in the Digital Operator's Manual in theve hi-
cle, on the internet and in the app.
% These are not small components. Information
about small components can be found using
th eke y phrase "Regulatory radio identi/cation
of small components". F F
urt
urt her
her com
com ponent-speci/c
ponent-speci/c inf
infor
ormation
mation Fu
rther component-speci/c information can be
fo und using theke y phrase "fur ther component-
speci/c information" in the Digital Owner's Man-
ual in theve hicle, on the internet and in the app. 414
414
Te
ch nical data

V
V
ehicle
ehicle identi/cation
identi/cation plat
plate, VIN and engine num-
e, VIN and engine num-
ber ov
ber overerview
view
V
V ehicle
ehicle identi/cation
identi/cation plate
plate Ve
hicle identi/cation plate (e xample:Kuwa it)
1 Vehicle manu facturer
2 Place of manufacture
3 Manu facturing date
4 Vehicle model
5 VIN Ve
hicle identi/cation plate (e xample: all other
countries)
1 Vehicle manu facturer
2 EUgeneral ope rating permit number (only for
cer tain countries)
3 VIN (vehicle identi/cation number)
4 Maximum permissible gross vehicle weight
(kg) Te
ch nical data
415
415

5
Maximum permissible gross weight of vehicle
combination (kg) (only for speci/c countries)
6 Maximum permissible front axle load (kg)
7 Maximum permissible rear axle load (kg)
8 Paint code
% The data shown in the illust ration is example
data. VIN belo
VIN belo
w t
w the fr
he fr ont r
ont r ight-hand seat
ight-hand seat 1
Imprinted VIN (vehicle identi/cation number)
2 Floor co vering VIN at t
VIN at t
he low
he lower edg
er edge of t
e of the windscr
he windscr een
een 1
VIN (vehicle identi/cation number) as label
The VIN as a label at the lo wer edge of the wind-
screen is only available in some countries.
Engine number
Engine number
The engine number is stamped into the crank-
case. Further information can be obtained at a
qu ali/ed specialist workshop. 416 416
Te
ch nical data

Oper
Oper
ating
ating 0uids
0uids N
No
ot
tes on oper
es on oper ating
ating0uids
0uids *
N
NOOTE
TE Mercedes-AMG vehicles #
Obser vethe no tes in the Supplement.
Yo u could otherwise failto recognise
dangers. &
W
W ARNING
ARNING Risk of injury from operating
0uids harmful toyour health
Operating 0uids may be poisonous and harm-
ful toyour health. #
Obser vethete xt on the original contain-
ers when using, storing or disposing of
operating 0uids. #
Always store operating 0uids sealed in
th eir original containers. #
Alwayske ep children away from operat-
ing 0uids. +
ENVIR
ENVIR
ONMENT
ONMENT AL NO
AL NOTE
TEPollution of the
environment due toirre sponsible disposal
of operating 0uids Incor
rect disposal of operating 0uids can
cause considerable damage tothe environ-
ment. #
Dispose of operating 0uids in an environ-
mentally responsible manner. Operating 0uids include
thefo llowing:
R fuels
R DeNOx agent AdBlue ®
forex haust gas aTer-
treatment
R lubricants
R coolant
R brake 0uid
R windscreen washer 0uid
R climate cont rol system refrigerant
Only use products appro vedby Mercedes-Benz.
Damage caused bythe use of products that ha ve
not been app rove d is not co veredby the
Mercedes-Benz warranty or goodwill gestu res. The operating 0uids appr
ovedby Mercedes-Benz
can be identi/ed bythefo llowing inscriptions on
th e container:
R MB-F reigabe (e.g. MB-F reigabe 229.51)
R MB-Appr oval (e.g. MB -Appr oval 229.51)
Fu rther information on appr oved operating 0uids:
R inthe Mercedes-Benz Speci/cations for Oper-
ating Fluids byentering the designation
- at https://be vo.mercedes-benz.com
- inthe Mercedes-Benz BeVo App
R Ataqu ali/ed specialist workshop &
W WARNING
ARNING Risk of /re or explosion from
fuel
Fu els are highly 0ammable. #
Fire , naked 0ames, smoking and creating
spar ksmust be avoided. #
Before and during refuelling, switch o.
th eve hicle and, if /tted, the stationary
heater. Te
ch nical data
417
417