stop start MERCEDES-BENZ E320 2003 W211 Owner's Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2003, Model line: E320, Model: MERCEDES-BENZ E320 2003 W211Pages: 399, PDF Size: 4.53 MB
Page 26 of 399
26 At a glanceCenter consoleLower part
Item
Page
1
Ashtray
231
2
KEYLESS-GO* start/stop
button
33
3
Selector lever for automat-
ic transmission
43,
151
4
Parking assist (Parktronic
system)* deactivation
switch
212
5
Adaptive damping system
(ADS)* switch
209
Item
Page
6
Vehicle level control
switch*
209
7
Thumbwheel for setting
distance for Distronic*
204
8
Distance warning func-
tion* on/off switch
205
9
Program mode selector for
automatic transmission
155
Page 32 of 399
32 Getting startedUnlockingUnlocking with KEYLESS-GO*
Your vehicle comes supplied with two
SmartKeys with remote controls and a re-
movable mechanical key. The locking tabs
for the mechanical key portion of the two
keys are a different color to help distin-
guish each key unit.
The function of the SmartKey overrules the
KEYLESS-GO function.
If you have the KEYLESS-GO function, your
vehicle checks whether the SmartKey with
KEYLESS-GO is valid when you grasp the
door handle. If your key is valid, the doors
will unlock, and you can open them.
Grasp the door handle.
The turn signal lamps blink once. The
locking knobs on the doors move up.
Pressing the KEYLESS-GO start/stop but-
ton on the selector lever corresponds to
turning the key to the various starter
switch positions.
iTo unlock the vehicle, the SmartKey
with KEYLESS-GO must be outside the
vehicle, no further than approx. 3 feet
(1 meter) away from the door. Warning!
G
When leaving the vehicle always take the
key and the SmartKey with KEYLESS-GO
with you, and lock the vehicle. Do not leave
children unattended in the vehicle, or with
access to an unlocked vehicle. Unsuper-
vised use of vehicle equipment may cause
serious personal injury.
Page 33 of 399
33 Getting started
Unlocking
1KEYLESS-GO start/stop button
Before you press the KEYLESS-GO
start/stop button, the vehicle’s on-board
electronics have status 0 (as with key re-
moved).Make sure the gear selector lever is set
toP.
Do not depress the brake pedal.
Position 1
Press the KEYLESS-GO start/stop but-
ton once.
This supplies power to some electrical
consumers, such as seat adjustment.Ignition (or position 2)
Press the KEYLESS-GO start/stop but-
ton twice.
This supplies power to all electrical
consumers. All the lights in the instru-
ment cluster light up.
More information can be found in the
"Controls in detail" section (
page 89).
For information on starting the engine us-
ing the KEYLESS-GO start/stop button,
see "Starting with KEYLESS-GO"
(
page 44).
iIf you now press the KEYLESS-GO
start/stop button twice, the power
supply is again switched off.
iIf you now press the KEYLESS-GO
start/stop button once, the power sup-
ply is again switched off.
Page 35 of 399
35 Getting started
Adjusting
Seat adjustment
The seat adjustment switches are located
in each door.
1Seat fore and aft adjustment
2Seat height
3Seat cushion tilt
4Backrest tilt
5Head restraint height
Turn the key in the starter switch to
position1or2.
or
Press the KEYLESS GO* start/stop
button once or twice.
or
Open the driver’s or passenger door.
Seat height
Press the switch up or down in the di-
rection of arrow2.
Seat fore and aft adjustment
Press the switch forward or backward
in the direction of arrow1.
Adjust to a comfortable seating posi-
tion that still allows you to reach the
accelerator / brake pedal safely. The
position should be as far to the rear as
possible, consistent with ability to
properly operate controls.
Infants and small children must be seated in
an appropriate infant or child restraint sys-
tem, which is properly secured with the ve-
hicle’s seat belt, fully in accordance with the
child seat manufacturer’s instructions.
A child’s risk of serious or fatal injuries is
significantly increased if the child restraints
are not properly secured in the vehicle and
the child is not properly secured in the child
restraint.
iWhen moving the seat, be sure that
there are no items in the footwell or be-
hind the seats. Otherwise you could
damage the seats.
Page 38 of 399
38 Getting startedAdjustingSteering wheel adjustment
The stalk is located on the steering column
(lower left).
1Steering column stalk, adjusts length
2Steering column stalk, adjusts height
Turn the key in the starter switch to
position1or2.
or
Press the KEYLESS GO* start/stop
button once or twice.
or
Open the driver or passenger door.Steering column, lengthen or shorten
Move stalk forward or backward in the
direction of arrow 1 until a comfortable
steering wheel position is reached with
your arms slightly bent at the elbow.
Steering column, height
Move the stalk up or down in the direc-
tion of arrow 2. Make sure that your
legs can move freely and that all the
displays (including malfunction and in-
dicator lamps) on the instrument clus-
ter are clearly visible.
Mirrors
Adjust the inside and exterior rear view
mirrors before driving so that you have a
good view of the road and traffic condi-
tions.
Inside rear view mirror
Manually adjust the inside rear view
mirror.
More information can be found in the
"Controls in detail" section (
page 157).
Warning!
G
In the case of an accident liquid electrolyte
may escape the mirror housing if the mirror
glass breaks.
Electrolyte has an irritating effect. Do not al-
low the liquid to come into contact with
eyes, skin, clothing, or respiratory system.
In case it does, immediately flush affected
area with water, and seek medical help if
necessary.
Page 44 of 399
44 Getting startedDrivingStarting with the key
Turn the key in the starter switch to
position3 and hold until the engine
starts (
page 31).
Depress the brake pedal.
The selector lever lock is released.
For information on turning off the engine
with the key, see “Turning off the engine”
(
page 51).
Starting with KEYLESS-GO*
You can start your vehicle without a key
using the KEYLESS-GO start/stop button
on the gear selector lever.1KEYLESS-GO start/stop button
Depress the brake pedal during the
starting procedure. Do not depress ac-
celerator.
The selector lever lock is released.
Press KEYLESS-GO start/stop
button1 once.
The engine starts automatically.
For information on turning off the engine
with KEYLESS-GO, see “Turning off with
KEYLESS-GO*” (
page 53).Starting difficulties
If the engine does not start as described,
carry out the following steps:
If you are starting the engine with the
key, turn key in starter switch to
position0 and repeat starting proce-
dure.
If you are starting the engine with
KEYLESS-GO*: Close any doors that
may be open to allow for better detec-
tion of the SmartKey with
KEYLESS-GO*.
Or:
Start the engine with the key as radio
signals from another source may be in-
terfering with the SmartKey with
KEYLESS-GO*.
Repeat the starting procedure
(page 43). Remember that extended
starting attempts can drain the battery.
iYou can also use the "touch-start" func-
tion. Turn the key to position3 and re-
lease it again immediately. The engine
then starts automatically.
!Ensure that the brake pedal is de-
pressed when starting the engine.
Page 49 of 399
49 Getting started
Driving
The coolant temperature is over 248°F
(120°C)
The coolant is too hot and is no longer
cooling the engine.
Stop the vehicle as soon as possible
and turn off the engine. Allow engine
and coolant to cool.
Check the coolant level and add cool-
ant if necessary (
page 264).In case of accident
If the vehicle is leaking gasoline:
Do not start the engine under any cir-
cumstances.
Notify local fire and/or police authori-
ties.
If the extent of the damage cannot be de-
termined:
Notify an authorized Mercedes-Benz
Center.If no damage can be determined on the
major assemblies
fuel system
engine mount
Start the engine in the usual manner.
Page 50 of 399
50 Getting startedParking and locking
Parking and lockingYou have now completed your first drive.
You have properly stopped and parked
your vehicle. End your drive as follows.
Parking brake
1Parking brake
2Release handle
Step firmly on parking brake1.
When the engine is running, the indica-
tor lamp ; (USA only) or 3
(Canada only) in the instrument cluster
will be illuminated.
Warning!
G
Wait until the vehicle is stationary before re-
moving the key from the starter switch. The
vehicle cannot be steered when the key is
removed.Warning!
G
With the engine not running, there is no
power assistance for the brake and steering
systems. In this case, it is important to keep
in mind that a considerably higher degree of
effort is necessary to stop or steer the vehi-
cle.
Warning!
G
Do not park this vehicle in areas where com-
bustible materials such as grass, hay or
leaves can come into contact with the hot
exhaust system, as these materials could be
ignited and cause a vehicle fire.
To reduce the risk of personal injury as a re-
sult of vehicle movement, before turning off
the engine and leaving the vehicle always:
Keep right foot on brake pedal.
Firmly depress parking brake pedal.
Move the selector lever to positionP.
Slowly release brake pedal.
When parked on an incline, turn front
wheel towards the road curb.
Turn the key to starter switch position0
and remove, or press start- / stop button
(vehicles with KEYLESS-GO*).
Take the key or the SmartKey with KEY-
LESS-GO* (if so equipped) and lock ve-
hicle when leaving.
Page 53 of 399
53 Getting started
Parking and locking
Turning off with KEYLESS-GO*
Place the gear selector lever in P.
Press the KEYLESS-GO start/stop but-
ton until the engine shuts off.
With the driver's door closed, the start-
er switch is now in position1. With the
driver’s door opened, the starter switch
is set to position0, same as key re-
moved from starter switch
(page 31).
Press the seat belt release button
(page 41).1Lock button on the door handle
After exiting the vehicle, press lock
button1 on the door handle or on the
trunk lid.
The locking knobs on the doors move
down. The turn signal indicators light
up briefly
!If you hear a warning signal you have ei-
ther
forgotten to turn off the lights, or
not put the gear selector lever inP
before opening the driver’s door.
Turn off the lights or place the gear se-
lector lever inP.
Warning!
G
To prevent possible personal injury, always
keep hands and fingers away from the door
openings when closing the doors. Be espe-
cially careful when small children are
around.
Before closing doors, ensure that there is no
possibility of someone getting caught in a
door during closing.
Page 56 of 399
56 Safety and SecurityOccupant safety
Occupant safetyIn this section you will learn the most im-
portant facts about the restraint systems
of the vehicle.
The restraint systems are
Seat belts
Emergency tensioning device
Airbags
Child seats
Child seat recognition
As independent systems their protective
effects work in conjunction with each oth-
er.The 1 warning lamp in the instrument
cluster lights up for about 4 seconds when
you turn the key in the starter switch to
position1 or2 or press the KEYLESS-GO*
(if so equipped) start/stop button once or
twice. It goes out when you start the en-
gine. This shows that the restraint systems
are operational.
If the lamp does not come on at all or if it
fails to extinguish after approximately
4 seconds or if it comes on thereafter, a
malfunction in the system has been de-
tected.
More information can be found in the
"Practical hints" section (
page 290).
iFor information on infants and children
traveling with you in the vehicle and re-
straint systems for infants and chil-
dren, see “Children in the vehicle”
(page 65).
Warning!
G
In the event that the SRS malfunction indica-
tor lamp lights up during driving or does not
come at all, the SRS may not be operational.
For your safety, we strongly recommend
that you visit an authorized Mercedes-Benz
Center immediately to have the system
checked; otherwise the SRS may not be ac-
tivated when needed in an accident, which
could result in serious or fatal injury, or it
might deploy unexpectedly and unnecessar-
ily which could also result in injury.
Improper work on the restraint systems, in-
cluding incorrect installation and removal,
can lead to possible injury through an unin-
tended activation of the SRS.
In addition, through improper work there is
a risk of rendering the SRS inoperative or
causing unintended airbag deployment.
Work on the SRS must therefore only be per-
formed by an authorized Mercedes-Benz
Center.