wheelbase MERCEDES-BENZ G-CLASS SUV 2008 Owner's Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2008, Model line: G-CLASS SUV, Model: MERCEDES-BENZ G-CLASS SUV 2008Pages: 293, PDF Size: 4.49 MB
Page 181 of 293

Trailer towing*
178 cialist workshop which has the necessary
specialist knowledge and tools to carry out
the work required.
Mercedes-Benz recommends that you use
a Mercedes-Benz Service Centre for this
purpose. In particular, work relevant to
safety or on safety-related systems must be
carried out at a qualified specialist work-
shop.
X Have the headlamps switched over at a
qualified specialist workshop, e. g. a
Mercedes-Benz Service Centre. G
Risk of accident
Have your headlamps switched back to
asymmetrical dipped beam if you are driv-
ing in a country in which traffic drives on
the same side of the road as in the country
in which your vehicle was registered. Oth-
erwise, you may dazzle the oncoming traffic
and could cause an accident. Trailer towing*
Notes on towing a trailer
G
Risk of accident
When reversing the vehicle towards the
trailer, make sure there is nobody between
the trailer and the vehicle.
Couple and uncouple the trailer carefully. If
you do not couple the trailer to the towing
vehicle correctly, the trailer could become
detached.
Make sure that the following values are not
exceeded:
R the permissible trailer drawbar nose-
weight
R the permissible trailer load
R the permissible rear axle load of the tow-
ing vehicle
R the maximum permissible gross vehicle
weight of both the towing vehicle and the
trailer
You will find the applicable permissible val-
ues, which must not be exceeded, in the
vehicle documents.
You will find the values approved by the
manufacturer on the vehicle identification plates and those for the towing vehicle in
the "Technical data" section.
You will find installation dimensions and loads
in the "Technical data" section
(Y page 274).
The maximum permissible trailer drawbar
noseweight on the ball coupling is:
R 140 kg (long-wheelbase station wagon)
R 115 kg (short-wheelbase station wagon
and cabriolet)
However, the actual noseweight must not
exceed the value given on the trailer coupling
and trailer identification plates. The lowest
weight applies.
! Use a drawbar noseweight as close as
possible to the maximum permissible nose-
weight. Do not use a noseweight of less
than 80 kg; otherwise, the trailer may come
loose.
Note that the payload and the rear axle load
are reduced by the actual payload.
i The height of the ball coupling changes
with the load of the vehicle. If necessary,
use a trailer with a height-adjustable draw-
bar. Operation
* optional
463_AKB; 1; 8, en-GB
wobuchh
,V ersion: 2.10.6
2008-07-17T15:19:41+02:00 - Seite 178 Dateiname: 6515_4091_02_buchblock.pdf; preflight
Page 191 of 293

Where will I find...?
188 Where will I find...?
Warning triangle, first-aid kit and
vehicle tool kit
G
Risk of injury
The jack is designed only to raise and hold
the vehicle for a short time while a wheel
is being changed.
You must use axle stands if you are carrying
out work on the vehicle.
Make sure that the jack is placed on a firm,
non-slip, level surface. Do not use wooden
blocks or similar objects as a jack underlay.
Otherwise, the jack will not be able to ach-
ieve its load-bearing capacity due to the
restricted height.
Do not start the engine at any time while a
wheel is being changed.
Do not lie under the vehicle when it is being
supported by the jack. If you do not raise
the vehicle as described, it could slip off the
jack (e.g. if the engine is started or a door
or the tailgate is opened or closed) and you
could be seriously injured.
i Check the expiry date of the first-aid kit
annually, and replace the contents when
necessary. i
When using the jack, you should also
observe the safety notes in the "Flat tyre"
section (Y page 243).
Long-wheelbase station wagon Warning triangle
The warning triangle is attached to the under-
side of the rear bench seat.
1
Warning triangle
2 Tabs
X Release tabs 2.
X Remove warning triangle 1. 1
Press-stud
2 Side reflectors
3 Leg
X To set up: fold feet1down and out to the
side.
X Pull side reflectors 2upwards to form a
triangle and lock them at the top using
upper press-stud 1. Practical advice
463_AKB; 1; 8, en-GB
wobuchh,
Version: 2.10.6 2008-07-17T15:19:41+02:00 - Seite 188Dateiname: 6515_4091_02_buchblock.pdf; preflight
Page 193 of 293

Where will I find...?
190
Short-wheelbase station wagon Warning triangle and vehicle tool kit
The warning triangle and vehicle tool kit are
located in the luggage compartment on the
left-hand side behind the side trim panel. 1
Cover
2 Warning triangle
3 Vehicle tool kit
X Vehicles with luggage nets*: fold the rear
bench seat forwards (Y page 142) for bet-
ter access.
X Open cover 1.
X Remove warning triangle 2or vehicle tool
kit 3.
X Set up the warning triangle (Y page 190).First-aid kit
The first-aid kit is located in the luggage com-
partment on the right-hand side behind the
side trim panel.
1
Cover
2 First-aid kit
X Vehicles with luggage net*: fold the rear
bench seat forwards (Y page 142) for bet-
ter access.
X Open cover 1.
X Remove first-aid kit 2.
i Short-wheelbase station wagon with
stowage compartments*: warning triangle
and vehicle tool kit are located in the left-
hand stowage compartment. The first-aid kit is located in the right-hand stowage
compartment.
Jack
The jack is located behind a cover in front of
the front-passenger seat. 1
Pins
2 Sleeves
3 Cover
X Slide the seat back (Y page 60).
X Pull pins 1out of sleeves 2.
X Pull sleeves 2out of cover 3.
X Remove cover 3. Practical advice
* optional
463_AKB; 1; 8, en-GB
wobuchh,
Version: 2.10.6 2008-07-17T15:19:41+02:00 - Seite 190Dateiname: 6515_4091_02_buchblock.pdf; preflight
Page 194 of 293

Where will I find...?
1911
Bar
2 Tab
3 Jack
X Pull bar 1upwards and detach from tab
2.
X Remove jack 3.
Cabriolet Warning triangle, first-aid kit and vehicle
tool kit
The warning triangle, first aid kit and vehicle
tool kit are located behind a cover in the tail-
gate. 1
Handle
2 Cover
X Open the tailgate (Y page 58).
X Fold out handle 1in the direction of the
arrow.
X Turn handle 1clockwise and fold up cover
2 in the direction of the arrow. 1
Warning triangle
2 First-aid kit
3 Vehicle tool kit
X Remove warning triangle 1, first-aid kit
2 or vehicle tool kit 3.
X Set up the warning triangle (Y page 188).
Jack
The jack is located behind a cover in front of
the front-passenger seat (as in the short-
wheelbase station wagon) (Y page 190). Practical advice
463_AKB; 1; 8, en-GB
wobuchh
, Version: 2.10.6 2008-07-17T15:19:41+02:00 - Seite 191 ZDateiname: 6515_4091_02_buchblock.pdf; preflight
Page 260 of 293

Fuses
257
To make it easier to change the fuse, you can
fold fuse box 5down slightly:
X Remove screws 6.
X Fold fuse box 5down. Fuse box on the transmission tunnel
Long-wheelbase Estate: you must remove the
stop clamps on the front-passenger seat in
order to reach the fuse box.
Removing the stop clamps G
Risk of injury
Do not drive if the stop clamps are not fitted
correctly. If you sit too closely to the airbag,
you risk serious or fatal injuries. Please
observe the instructions on occupant
safety in the "Safety" section. The stop clamps are at the front of the seat
rails. Stop clamp of the right seat rail, reverse image for
the left
1
Stop clamp
2 Distance
X Remove stop clamp 1with a screwdriver.
X When replacing the stop clamps, make sure
you maintain correct distance 2.Opening the fuse box 1
Screws
2 Cover
X Adjust the front-passenger seat to its fore-
most position.
X Remove screws 1.
X Remove cover 2(arrow). Practical advice
463_AKB; 1; 8, en-GB
wobuchh,
Version: 2.10.6 2008-07-17T15:19:41+02:00 - Seite 257 ZDateiname: 6515_4091_02_buchblock.pdf; preflight
Page 272 of 293

Vehicle dimensions
269Vehicle dimensions
Long wheelbase station wagon Short wheelbase station wagon
Vehicle length (ECE)
23 4,668 – 4,811 mm 4,218 – 4,361 mm
Vehicle width with mirrors fol-
ded out 23 2,007 mm 2,007 mm
Vehicle width with mirrors fol-
ded in 23 1,760 – 1,885 mm 1,760 – 1,810 mm
Vehicle height
23 1,927 – 1,977 mm 1,927 – 1,977 mm
Ground clearance
23 205 – 230 mm 205 – 230 mm
Wheelbase
2,850 mm 2,400 mm
Turning circle
13.2 – 13.3 mm 11.3 m
G 55 AMG Cabriolet
Vehicle length (ECE)
4,690 mm
4,263 – 4,406 mm
24 Vehicle width with mirrors fol-
ded out 2,005 mm
2,007 mm
24 Vehicle width with mirrors fol-
ded in 1,855 mm
1,760 – 1,810 mm
24 Vehicle height
1,965 mm
1,927 – 1,977 mm
24 23
Dimensions may vary according to vehicle equipment.
24 Dimensions may vary according to vehicle equipment. Te
chnical da ta
463_AKB; 1; 8, en-GB
wobuchh
,V ersion: 2.10.6
2008-07-17T15:19:41+02:00 - Seite 269 ZDateiname: 6515_4091_02_buchblock.pdf; preflight
Page 273 of 293

Vehicle dimensions
270 G 55 AMG Cabriolet
Ground clearance
200 mm
205 – 230 mm
24 Wheelbase
2,850 mm 2,400 mm
Turning circle
13.3 m 11.3 m
24
Dimensions may vary according to vehicle equipment. Te
chnical da ta
463_AKB; 1; 8, en-GB
wobuchh
,V ersion: 2.10.6
2008-07-17T15:19:41+02:00 - Seite 270 Dateiname: 6515_4091_02_buchblock.pdf; preflight
Page 274 of 293

Vehicle weights
271Vehicle weights
The unladen weight includes the driver (68 kg), luggage (7 kg) and all fluids (fuel tank 90% full). Items of optional equipment increase the
unladen weight and reduce the maximum pa yload. Specific weight specifications can be found on the vehicle identification plate
(Y page 261).
Long wheelbase station wagon G 500 G 320 CDI G 55 AMG
Unladen weight (in accordance with EC direc-
tive) 2,450 kg 2,445 kg 2,595 kg
Maximum permissible gross vehicle weight
3,200 kg 3,200 kg 3,200 kg
Maximum permissible front axle load
1,450 kg 1,450 kg 1,450 kg
Maximum permissible rear axle load
1,900 kg 1,900 kg 1,900 kg
Only when towing a trailer: permissible gross
weight of vehicle/trailer combination
6,700 kg 6,700 kg 6,700 kg
Maximum roof load
200 kg 200 kg 200 kg
Maximum permissible load 750 kg 755 kg 605 kgTechnical data
463_AKB; 1; 8, en-GB
wobuchh,
Version: 2.10.6 2008-07-17T15:19:41+02:00 - Seite 271 ZDateiname: 6515_4091_02_buchblock.pdf; preflight
Page 275 of 293

Vehicle weights
272
Short wheelbase station wagon G 500 G 320 CDI
Unladen weight (in accordance with EC direc-
tive) 2,315 kg 2,275 kg
Maximum permissible gross vehicle weight
2,850 kg 2,850 kg
Maximum permissible front axle load
1,400 kg 1,400 kg
Maximum permissible rear axle load
1,700 kg 1,700 kg
Only when towing a trailer: permissible gross
weight of vehicle/trailer combination 5,700 kg 5,700 kg
Only when towing a trailer: permissible rear
axle load 25 1,800 kg 1,800 kg
Maximum roof load
150 kg 150 kg
Maximum permissible load 535 kg 575 kg
Cabriolet
G 500 G 320 CDI
Unladen weight (in accordance with EC direc-
tive) 2,300 kg 2,260 kg
Maximum permissible gross vehicle weight
2,850 kg 2,850 kg
Maximum permissible front axle load
1,400 kg 1,400 kg
25
Drawbar noseweight is not included in the trailer load. Te
chnical da ta
463_AKB; 1; 8, en-GB
wobuchh
,V ersion: 2.10.6
2008-07-17T15:19:41+02:00 - Seite 272 Dateiname: 6515_4091_02_buchblock.pdf; preflight
Page 278 of 293

Trailer coupling*
275Trailer loads
Long-wheelbase station wagon Short-wheelbase station
wagon Cabriolet
Permissible trailer load, unbraked
750 kg 750 kg 750 kg
Permissible trailer load, braked
27 3,500 kg 2,850 kg 2,850 kg
Maximum drawbar noseweight
28 140 kg 115 kg 115 kg
27
At a minimum gradient-climbing capability of 12% from a standstill.
28 The drawbar noseweight is not included in the trailer load. Techni
cal data
* optional
463_AKB; 1; 8, en-GB
wobuchh
,V ersion: 2.10.6
2008-07-17T15:19:41+02:00 - Seite 275 ZDateiname: 6515_4091_02_buchblock.pdf; preflight