window MERCEDES-BENZ G500 2007 W463 Owner's Guide

193 Controls in detail
Power windows
Fully opening the windows
(Express-open)
Press switch2, 3, 4 or5 past the
resistance point and release.
The corresponding window opens
completely.
Stopping the windows during
Express-operation
Press or pull the respective switch
again.
The movement of the window stops.
Summer opening feature
If the weather is warm, you can ventilate
the vehicle before driving off by simulta-
neously opening the windows and the
tilt/sliding sunroof.Aim transmitter eye of the SmartKey at
the driver’s outside door handle.
The SmartKey must be in close
proximity to the driver’s outside door
handle.
Press and hold buttonΠon the
SmartKey until the windows and the
tilt/sliding sunroof have reached the
desired position.
Release buttonΠon the SmartKey
to interrupt the opening procedure.

194 Controls in detail
Power windows
Convenience closing feature
When locking the vehicle, you can close
the windows and the tilt/sliding sunroof
simultaneously.Aim transmitter eye of the SmartKey at
the driver’s outside door handle
(
page 193).
The SmartKey must be in close
proximity to the driver’s outside door
handle.
Press and hold button‹ on the
SmartKey until the windows and the
tilt/sliding sunroof are completely
closed.
Release button‹ on the SmartKey
to interrupt the closing procedure.
Warning!G
When closing the windows and the
tilt/sliding sunroof, make sure that there is
no danger of anyone being harmed by the
closing procedure.
If potential danger exists, proceed as
follows:

Release button‹ to stop the closing
procedure. To open, press and hold
buttonŒ. To continue the closing
procedure after making sure that there
is no danger of anyone being harmed by
the closing procedure, press and hold
button‹.

196 Controls in detail
Power tilt/sliding sunroof
Switch on the ignition (page 39).Opening and closing the tilt/sliding
sunroof
To open, close, raise, or lower the
tilt/sliding sunroof, move the sunroof
switch to the resistance point in the
required direction of arrows1 to4
(
page 195).
Release the sunroof switch when the
tilt/sliding sunroof has reached the
desired position.
Fully opening the tilt/sliding sunroof
(Express-open)
Move the sunroof switch past the
resistance point in direction of
arrow4 (
page 195) and release.
The tilt/sliding sunroof opens
completely.Stopping the tilt/sliding sunroof during
Express-operation
Move the sunroof switch in any
direction.
The movement of the tilt/sliding
sunroof stops.
!Please keep in mind that weather conditions
can sometime change rapidly. Make sure to
close the tilt/sliding sunroof when leaving the
vehicle. If water enters the vehicle interior,
vehicle electronics could be damaged which is
not covered by the Mercedes-Benz Limited
Warranty.
iWhen the tilt/sliding sunroof is open,
resonance noises may result in addition to the
usual wind noises. They are caused by minimal
pressure changes in the passenger compart-
ment. To reduce or eliminate these noises,
change the position of the tilt/sliding sunroof or
open a side window slightly.
iYou can also open or close the tilt/sliding
sunroof using the SmartKey, see “Summer open-
ing feature” (
page 193) and see “Convenience
closing feature” (
page 194).
Warning!G
The opening procedure of the tilt/sliding
sunroof can be immediately halted by
releasing the switch or, if the switch was
moved past the resistance point and
released, by moving the switch in any
direction.
The closing procedure of the tilt/sliding sun-
roof can be immediately halted by releasing
the switch.
The closing procedure of the tilt/sliding sun-
roof can be immediately reversed by moving
the switch in direction1 or4.

204 Controls in detail
Driving systems
The rear view camera is an optical parking
aid. It shows you the area behind the
vehicle in the COMAND system display
when reverse gearR is engaged, for
example during parallel parking.
To function properly, the camera lens must
be free of dirt, ice, snow, and slush. Clean
the camera lens regularly, being careful
not to scratch or damage the camera lens,
see “Cleaning the rear view camera lens”
(
page 319).The rear view camera is on the tailgate
above the rear window wiper.
1Rear view camera
Switching the rear view camera on
Switch on the ignition (page 39).
Switch on the COMAND system.
Refer to separate COMAND system
operating instructions.

there is a sudden change in tempera-
ture, e.g. if you drive into a heated
garage from the cold (lens condensa-
tion)

the camera lens is dirty or covered

the rear of your vehicle is damaged
In this case, have the position and
setting of the camera checked by a
qualified specialist workshop.
Mercedes-Benz recommends that you
contact a Mercedes-Benz Light Truck
Center for this purpose.
Do not use the rear view camera in these sit-
uations. Otherwise you could injure yourself
or others and/or damage property including
your vehicle while parking/maneuvering.


230 Controls in detail
Useful features
System self-check
Initially, after switching on the ignition,
malfunctions are detected and indicated
(the indicator lamps in the SOS button, the
Roadside Assistance button• and the
Information button¡ stay on longer
than 10 seconds or do not come on). The
message
Tele Aid inoperative appears
in the multifunction display.Emergency calls
An emergency call is initiated auto-
matically following an accident in which
the emergency tensioning devices (ETDs)
or air bags deploy.
An emergency call can also be initiated
manually by opening the cover next to the
interior rear view mirror labeled SOS, then
briefly pressing the button located under
the cover. See (
page 231) for
instructions on initiating an emergency call
manually.
Once the emergency call is in progress, the
indicator lamp on the SOS button will
begin to flash. The message
Connecting
call
appears in the multifunction display.
When the connection is established, the
message
Call connected appears in the
multifunction display. All information
relevant to the emergency, such as the
location of the vehicle (determined by the
GPS satellite location system), vehicle
model, identification number and color are
generated.
iWhen a Tele Aid call has been initiated,
the COMAND system audio is muted and the
selected mode (radio, CD etc.) pauses.
The optional cellular phone (if installed) inserted
in cradle switches off. If you must use this
phone, we recommend that you use it only with
the vehicle at a standstill in a safe location.
Remove the phone from the cradle and place the
call. The navigation system (if engaged) will con-
tinue to run. The display in the instrument cluster
is available for use, and spoken commands are
only available by pressing the RPT button on the
COMAND system. A pop-up window will appear
in the COMAND system display to indicate that a
Tele Aid call is in progress. After the Tele Aid call
has ended, the optional cellular phone inserted
in the cradle switches on again. A PIN entry
might be necessary.
Warning!G
If the indicator lamps on the SOS button, on
the Roadside Assistance button, and/or on
the Information button remain illuminated
continuously in red and/or the message
Tele Aid inoperative is displayed in the
multifunction display after the system
self-check, a malfunction in the system has
been detected.
If a malfunction is indicated as outlined
above, the system may not operate as
expected. Have the system checked at the
nearest Mercedes-Benz Light Truck Center
as soon as possible.

251 Operation
Driving instructions
Winter driving instructions
The most important rule for slippery or icy
roads is to drive sensibly and to avoid
abrupt acceleration, braking and steering
maneuvers. Do not use the cruise control
system under such conditions.
When the vehicle is in danger of skidding,
move the gear selector lever to neutral
positionN. Try to keep the vehicle under
control by corrective steering action.Road salts and chemicals can adversely
affect braking efficiency. Increased pedal
force may become necessary to produce
the normal brake effect.
Depressing the brake pedal periodically
when traveling at length on salt-strewn
roads can bring road-salt-impaired braking
efficiency back to normal.
If the vehicle is parked after being driven
on salt-treated roads, the braking
efficiency should be tested as soon as
possible after driving is resumed.
For more information, see “Winter driving”
(
page 309).
iFor information on driving with snow chains,
see “Snow chains” (
page 310).
Warning!G
On slippery road surfaces, never downshift
in order to obtain braking action. This could
result in drive wheel slip and reduced vehi-
cle control. Your vehicle’s ABS will not pre-
vent this type of control loss.
Do not engage the transfer case in position
LOW when driving on ice or packed snow.
At speeds below 18 mph (30 km/h) vehicle
steering is adversely affected by the LOW
RANGE – ABS (
page 90).
Warning!G
Make sure not to endanger any other road
users when carrying out these braking
maneuvers.
Warning!G
If the vehicle becomes stuck in snow, make
sure that snow is kept clear of the exhaust
pipe and from around the vehicle with the
engine running. Otherwise, deadly carbon
monoxide (CO) gases may enter vehicle
interior resulting in unconsciousness and
death.
To assure sufficient fresh air ventilation,
open a window slightly on the side of the
vehicle not facing the wind.
Warning!G
The outside temperature indicator is not
designed to serve as an ice-warning device
and is therefore unsuitable for that purpose.
Indicated temperatures just above the
freezing point do not guarantee that the
road surface is free of ice.

254 Operation
Driving instructions
Checklist before off-road driving
Engine oil level

Check the engine oil level with the
control system (
page 270). The
message
Engine oil level OK must
appear in the multifunction display.
Only then can the vehicle obtain a
trouble-free oil supply, even on steep
gradients.
!Observe the following during off-road
driving:

Keep doors, tailgate, windows, and
tilt/sliding sunroof closed.

Switch cruise control off.

Adjust vehicle speed to condition of terrain.
The more uneven, rutty, and steeper the
terrain, the lower the speed should be. Drive
through water slowly at an even speed,
avoiding a bow wave.

Be especially careful when driving in
unknown territory. It may be necessary to
get out of the vehicle and scout the path you
intend to take.

Watch out for obstacles, such as rocks,
holes, tree stumps, and ruts.

Avoid excessive engine speeds – drive at
moderate engine speeds (max. 3 000 rpm).

Before driving through water, determine its
depth.

Do not stop vehicle while immersed in water,
and do not shut off the engine.

In sandy soil, drive at a steady speed as
allowed by conditions. This helps overcome
the vehicle rolling resistance and reduces
the likelihood of the vehicle sinking into the
ground.

Do not initiate jumps with the vehicle. It
interrupts the forward momentum of the
vehicle.

Always drive on slopes with the engine
running and the vehicle in gear.

Inspect the vehicle for possible damage after
each off-road trip.
Warning!G
Do not reduce the tire inflation pressure
before driving through sand. However, if you
do so, remember to correct the tire inflation
pressure (
page 288) before continuing
your trip. Driving with reduced tire inflation
pressure increases the risk of losing control
of the vehicle and rolling over.
!If a engine oil level warning message
(
page 351) appears in the multifunction
display while driving, stop the vehicle in a safe
location or as soon at is safe to do so. Check the
engine oil level (
page 270).
The engine oil level warning messages should
not be ignored. Extended driving with the
message displayed could result in serious engine
damage that is not covered by the
Mercedes-Benz Limited Warranty.

263 Operation
Driving instructions
Emission control
Certain engine systems serve to keep the
toxic components of the exhaust gases
within permissible limits required by law.
These systems, of course, will function
properly only when maintained strictly
according to factory specifications. Any
adjustments on the engine should,
therefore, be carried out only by qualified
Mercedes-Benz Light Truck Center autho-
rized technicians.
Engine adjustments should not be altered
in any way. Moreover, the specified service
jobs must be carried out regularly
according to Mercedes-Benz servicing
requirements. For details refer to the
Maintenance Booklet.
Coolant temperature
During severe operating conditions,
e.g. stop-and-go traffic, the coolant tem-
perature may rise close to approximately
248°F (120°C).The engine should not be operated with
the coolant temperature above 248°F
(120°C). Doing so may cause serious
engine damage which is not covered by the
Mercedes-Benz Limited Warranty.
Warning!G
Inhalation of exhaust gas is hazardous to
your health. All exhaust gas contains carbon
monoxide (CO), and inhaling it can cause
unconsciousness and possible death.
Do not run the engine in confined areas
(such as a garage) which are not properly
ventilated. If you think that exhaust gas
fumes are entering the vehicle while driving,
have the cause determined and corrected
immediately. If you must drive under these
conditions, drive only with at least one
window fully open at all times.
iExcessive coolant temperatures trigger a
warning message in the multifunction display
(
page 348).
Warning!G

Driving when your engine is overheated
can cause some fluids, which may have
leaked into the engine compartment to
catch fire. You could be seriously
burned.

Steam from an overheated engine can
cause serious burns which can occur
just by opening the hood. Stay away
from the engine if you see or hear steam
coming from it.
Turn off the engine, get out of the vehicle
and do not stand near the vehicle until the
engine has cooled down.

266 Operation
At the gas station
G55AMG
1Coolant
2Brake fluidBrake fluid
Coolant
For normal replenishing, use water
(potable water quality).
For more information, see “Coolant level”
(
page 274) and see “Fuels, coolants, lu-
bricants, etc.” (
page 422).Engine oil level
For more information on engine oil, see
“Engine oil” (
page 269).
Windshield/rear window washer sys-
tem and headlamp cleaning system
For more information on refilling the
washer reservoir, see “Windshield/rear
window washer system and headlamp
cleaning system” (
page 275).
Vehicle lighting
Check function and cleanliness.
For information on replacing light bulbs,
see “Replacing bulbs” (
page 377).
For more information, see “Exterior lamp
switch” (
page 117).
Tire inflation pressure
For more information, see “Checking tire
inflation pressure” (
page 288).
!If you find that the brake fluid in the brake
fluid reservoir has fallen to the minimum mark or
below, have the brake system checked for brake
pad thickness and leaks immediately. Notify an
authorized Mercedes-Benz Light Truck Center
immediately. Do not add brake fluid as this will
not solve the problem.
For more information, see “Practical hints”
(
page 326) and see “Brake fluid”
(
page 425).

275 Operation
Engine compartment
Using a rag, turn cap1 slowly approx-
imately one half turn counterclockwise
to release any excess pressure.
Continue turning cap1 counterclock-
wise and remove it.
The coolant level is correct if the level

for cold coolant: reaches the top of
the mark (plastic bridge) visible
through the filling opening

for warm coolant: is approximately
0.6 in (1.5 cm) higher
Add coolant as required.
Replace cap1 on the filler neck.
Tighten cap1 clockwise until you
hear it click three times.
For more information on coolant, see
“Coolants” (
page 427).Windshield/rear window washer
system and headlamp cleaning system
The windshield washer reservoir is located
on the passenger side of the engine
compartment.
1CapFluid for the windshield/rear window
washer system and the headlamp cleaning
system is supplied from the windshield
washer reservoir. It has a capacity of
7.9 US qt (7.5 l).
During all seasons, add MB Windshield
Washer Concentrate “MB SummerFit” to
water. Premix the windshield washer fluid
in a suitable container.
Warning!G
Washer solvent/antifreeze is highly flamma-
ble. Do not spill washer solvent/antifreeze
on hot engine parts, because it may ignite
and burn. You could be seriously burned.