stop start MERCEDES-BENZ G55AMG 2008 W463 Owner's Manual

45
Getting started
Adjusting
Adjusting steering wheel in or out
Move stalk forward or backward in
direction of arrow
1.
Adjusting steering wheel up or down
Move stalk up or down in direction of
arrow 2.
For information on “Heated steering
wheel”, see (
page 225).
Easy-entry/exit feature
This feature allows for easier entry into and
exit from the vehicle. When entering and
exiting the vehicle, the steering wheel is in
its uppermost position.
The easy-entry/exit feature can be
activated or deactivated in the
Convenience submenu of the control
system (
page 156). With the easy-entry/exit
feature activated,
the steering wheel will return to its last set
position when you:

close the driver’s door with the ignition
switched on
or

insert the SmartKey into the starter
switch with the driver’s door closed
With the easy-entry/exit feature activated,
the steering wheel tilts upwards when you:

remove the SmartKey from the starter
switch
or

open the driver’s door with the
SmartKey in starter switch position 0
or 1
Warning!G
You must make sure no one can become
trapped or injured by the moving steering
wheel when the easy-entry/exit feature is
activated.
To stop steering wheel movement, do one of
the following:

Move the steering wheel adjustment
stalk (
page 44).

Press one of the stored position buttons
or the memory button (
page 115).
Do not leave children unattended in the
vehicle, or with access to an unlocked
vehicle. Children could open the driver’s
door and unintentionally activate the
easy-entry/exit feature, which could result
in an accident and/or serious personal
injury.
iThe last set steering wheel position is stored
when

the ignition is switched off (page 39)

the position is stored into memory
(
page 115)
W463.boo Seite 45 Montag, 19. November 2007 8:41 08

55
Getting started
Driving
Remember that extended starting
attempts can drain the battery.
Get a jump start (page 397).
If the engine does not start after several
starting attempts, there could be a mal-
function in the engine electronics or in the
fuel supply system.
Contact an authorized Mercedes-Benz
Light Truck Center or call Roadside
Assistance.
Parking brake 1
Parking brake lever
2 Release buttonPull up slightly on parking brake
lever 1 and press release button 2.
Push parking brake lever 1 down to
its original position.
The brake warning lamp ;
(USA only) or 3 (Canada only) in
the instrument cluster goes out.
Driving off
Depress the brake pedal.
The gear selector lever lock is released.
Move the gear selector lever to drive
position D or reverse gear R.
Release the brake pedal.
Carefully depress the accelerator.
Warning!G
When leaving the vehicl e, always remove the
SmartKey from the starter switch, take it
with you, and lock the vehicle. Do not leave
children unattended in the vehicle, or with
access to an unlocked vehicle. Children
could release the parking brake, which
could result in an accident and/or serious
personal injury.
!In order to avoid damage to the transmis-
sion:

Wait for the gear selection process to com-
plete before setting the vehicle in motion.

Place the gear selector lever in park
position P or reverse gear R only when the
vehicle is stopped.
!If you hear a warning signal and the
message
Release parking brake appears in
the multifunction display when driving off, you
have forgotten to release the parking brake.
Release the parking brake (
page 55).
W463.boo Seite 55 Montag, 19. November 2007 8:41 08

58 Getting started
Driving
Windshield wipers
The combination switch is located on the
left of the steering column.
Combination switch
1Single wipe
Wiping with windshield washer fluid
2 Switching on windshield wipers
Switch on the ignition (page 39). Switching on windshield wipers
Turn the combination switch to the
desired position depending on the
intensity of the rain.
0
Windshield wipers off
I Intermittent wiping
II Normal wiper speed
III Fast wiper speed
!Do not operate the windshield wipers when
the windshield is dry. Dust that accumulates on
a windshield might scratch the glass and/or
damage the wiper blades when wiping occurs on
a dry windshield. If it is necessary to operate the
windshield wipers in dry weather conditions,
always operate the windshield wipers with
windshield washer fluid (
page 59).
!If anything blocks the windshield wipers
(leaves, snow, etc.), switch them off
immediately.

For safety reasons, stop the vehicle in a safe
location, turn off the engine and remove the
SmartKey from the starter switch before
attempting to remove any blockage.

Remove blockage.

Turn the windshield wipers on again.
If the windshield wipers fail to function at all with
the combination switch in position I,

set the combination switch to the next
higher wiper speed

have the windshield wipers checked at the
nearest authorized Mercedes-Benz Light
Truck Center.
W463.boo Seite 58 Montag, 19. November 2007 8:41 08

61
Getting started
Driving
Problems while driving
The engine runs erratically and misfires

An ignition cable may be damaged.

The engine electronics may not be
operating properly.

Unburned gasoline may have entered
the catalytic converter and damaged it.
Give very little gas.
Have the problem repaired at an
authorized Mercedes
-Benz Light Truck
Center as soon as possible. The coolant temperature is above
248°F (120°C)
The coolant is too hot and is no longer
cooling the engine.
Stop the vehicle in a safe location as
soon as possible and turn off the
engine. Allow engine and coolant to
cool off.
Check the coolant level and add
coolant if necessary (
page 274).
In case of accident
If the vehicle is leaking fuel:
Do not start the engine under any
circumstances.
Notify local fire and/or police
authorities.
If the extent of the damage cannot be
determined:
Contact an authoriz ed Mercedes-Benz
Light Truck Center or call Roadside
Assistance.
If no damage can be determined on the

major assemblies

fuel system

engine mount:
Start the engine in the usual manner.
iExcessive coolant temperatures trigger a
warning message in the multifunction display
(
page 346).
W463.boo Seite 61 Montag, 19. November 2007 8:41 08

62 Getting started
Parking and locking
You have now completed your first drive.
You have properly stopped and parked
your vehicle. End your drive as follows.Parking brake
Warning!G
With the engine not running, there is no
power assistance for the brake and the
steering system. In this case, it is important
to keep in mind that a considerably higher
degree of effort is necessary to brake and
steer the vehicle.
Warning!G
Do not park this vehicle in areas where
combustible materials such as grass, hay or
leaves can come into contact with the hot
exhaust system, as thes e materials could be
ignited and cause a vehicle fire.
To reduce the risk of personal injury or
damage to the vehicle drivetrain as a result
of vehicle movement, before turning off the
engine and leaving the vehicle always:

Keep right foot on brake pedal.

Pull the parking brake lever up as many
notches as possible.

Move the gear selector lever to park
position P.

Slowly release brake pedal.

When parked on an incline, turn front
wheels towards the road curb.

Turn the SmartKey in the starter switch
position 0 and remove.

Take the SmartKey with you and lock
vehicle when leaving.
Warning!G
Engaging the parking brake while the vehicle
is in motion can cause the rear wheels to
lock up. You could lose control of the vehicle
and cause an accident. In addition, the
vehicle’s brake lights do not light up when
the parking brake is engaged.
W463.boo Seite 62 Montag, 19. November 2007 8:41 08

64 Getting started
Parking and locking
Switching off headlamps
Turn the exterior lamp switch toM
(
page 56).
For more information, see “Lighting”
(
page 117).
Turning off engine
Move the gear selector lever to park
position P. Apply the parking brake (
page 62).
Turn SmartKey in the starter switch to
position
0.
Remove the SmartKey from the starter
switch.
The immobilizer is activated.
Releasing seat belts
Press seat belt release button
(
page 50).
Allow the retractor to completely
rewind the seat belt by guiding latch
plate.
Warning!G
Do not turn off the engine before the vehicle
has come to a complete stop. With the
engine not running, there is no power assis-
tance for the brake and steering systems. In
this case, it is important to keep in mind that
a considerably higher degree of effort is
necessary to brake and steer the vehicle.
iAlways set the parking brake in addition to
shifting to park position P (
page 164).
On slopes, turn the front wheels towards the
road curb.
iThe SmartKey can only be removed from the
starter switch with the gear selector lever in park
position P and the SmartKey in starter switch
position 0.
!M a k e s u r e t h e s e a t b e l t r e t r a c t s f u l l y s o t h a t
the seat belt and/or latch plate cannot get
caught or pinched in the door or in the seat
mechanism. This can damage the seat belt and
impair the effectiveness of the seat belt, and/or
cause damage to the door and/or door trim
panel. Such damage is not covered by the
Mercedes-Benz Limited Warranty.
Damaged seat belts must be replaced. Contact
an authorized Mercedes-Benz Light Truck
Center.
W463.boo Seite 64 Montag, 19. November 2007 8:41 08

117
Controls in detail
Lighting
 Lighting
For information on how to switch on the
headlamps and use the turn signals, see
“Switching on headlamps” (
page 56)
and see “Turn signals” (
page 57).
Exterior lamp switch
The exterior lamp switch is located on the
dashboard to the left of the steering wheel.
iIf you drive in countries where vehicles drive
on the other side of the road than the country in
which the vehicle is registered, you must have
the headlamps modified for symmetrical low
beams. Relevant information can be obtained at
any authorized Mercedes-Benz Light Truck
Center.
1‚Standing lamps, left
(turn left two stops)
2ˆStanding lamps, right
(turn left one stop)
3MOff
Daytime running lamp mode
(
page 119)
4UAutomatic headlamp mode
Daytime running lamp mode
(
page 119)
5CParking lamps (also tail lamps,
license plate lamps, side mark-
er lamps, instrument panel
lamps)
6BLow beam headlamps or high
beam headlamps
7‡Front fog lamps
8†Rear fog lamp
iIf you hear a warning signal you have forgot-
ten to switch off the low beam headlamps or the
parking lamps before opening the driver’s door.
In addition the message
Switch off lights
appears in the multifunction display.
Switch off the low beam headlamps or the park-
ing lamps.
If the message
Turn off lights or remove
key
appears in the multifunction display remove
the SmartKey from the starter switch or switch
off the automatic headlamp mode.
!Failure to switch off the exterior lamps when
leaving the vehicle may result in a discharged
battery.
W463.boo Seite 117 Montag, 19 . November 2007 8:41 08

164 Controls in detail
Automatic transmission
Gear selector lever positions
The current gear selector lever position
appears in the multifunction display.1 Current gear selector lever positionEffect
ìPark position
Gear selector lever position
when the vehicle is parked. Place
gear selector lever in park
position P only when vehicle is
stopped. The park position is not
intended to serve as a brake
when the vehicle is parked.
Rather, the driver should always
set the parking brake in addition
to placing the gear selector lever
in park position P to secure the
vehicle.
Effect
The SmartKey can only be
removed from the starter switch
with the gear selector lever in
park position P. With the
SmartKey removed, the gear
selector lever is locked in park
position P.
If the vehicle’s electrical system
is malfunctioning, the gear
selector lever could remain
locked in park position P
(
page 371).
íReverse gear
Place gear selector lever in
position R only when vehicle is
stopped.
W463.boo Seite 164 Montag, 19 . November 2007 8:41 08

169
Controls in detail
Automatic transmission
Canceling gear range limit
Press and hold the gear selector lever
in the
D+direction until
Dreappears in
the multifunction display (
page 164).
The transmission will shift from the
current gear range directly to gear
range D.
Shifting into optimal gear range
Press and hold the gear selector lever
in the D-direction.
The transmission will automatically
select the gear range suited for optimal
acceleration and deceleration. This will
involve shifting down one or more
gears. Emergency operation
(Limp-Home Mode)
If vehicle acceleration becomes less
responsive or sluggish or the transmission
no longer shifts, the transmission is most
likely operating in limp-home (emergency
operation) mode. In this mode only second
gear and reverse gear can be selected.
Stop the vehicle in a safe location.
Move the gear selector lever to park
position
P.
Turn off the engine.
Wait at least 10 seconds before
restarting.
Restart the engine.
Move the gear selector lever to
position D (for second gear) or
position R.
Have the transmission checked at an
authorized Mercedes -Benz Light Truck
Center as soon as possible.
W463.boo Seite 169 Montag, 19 . November 2007 8:41 08

246 Operation
Driving instructions
Power assistance
BrakesTo help prevent brake disk corrosion after
driving on wet road surfaces (particularly
salted roads), it is advisable to brake the
vehicle with considerable force prior to
parking. The heat generated serves to dry
the brakes.
If your brake system is normally only
subjected to moderate loads, you should
occasionally test the effectiveness of the
brakes by applying above-normal braking
pressure at higher speeds. This will also
enhance the grip of the brake pads.
Warning!G
With the engine not running, there is no
power assistance for the brake and steering
systems. In this case, it is important to keep
in mind that a considerably higher degree of
effort is necessary to brake and steer the
vehicle.
Warning!G
After driving in heavy
rain for some time
without applying the brakes or through
water deep enough to wet brake compo-
nents or salty road conditions, the first brak-
ing action may be somewhat reduced and
increased pedal pressure may be necessary
to obtain expected br aking effect. Maintain
a safe distance from vehicles in front.
Resting your foot on the brake pedal will
cause excessive and premature wear of the
brake pads.
It can also result in the brakes overheating,
thereby significantly reducing their effec-
tiveness. It may not be possible to stop the
vehicle in sufficient ti me to avoid an acci-
dent.
!Operational or performance test must only
be conducted on a two-axle dynamometer. If
such tests are necessary, contact an authorized
Mercedes-Benz Light Truck Center. You could
otherwise seriously damage the brake system or
the transfer case which is not covered by the
Mercedes-Benz Limited Warranty.
!Because the ESP® operates automatically,
the engine and ignition must be shut off
(SmartKey in starter switch position 0 or 1)
when testing the parking brake on a brake test
dynamometer and such testing should be no
longer than 10 seconds.
Active braking action through the ESP
® may
otherwise seriously damage the brake system
which is not covered by the Mercedes-Benz
Limited Warranty.
Warning!G
Make sure not to endanger any other road
users when carrying out these braking
maneuvers.
W463.boo Seite 246 Montag, 19 . November 2007 8:41 08