oil dipstick MERCEDES-BENZ ML320 1997 Complete Owner's Manual

AP18.00-P-0101-02Z
Extract engine oil

Commercially available tools
(see Workshop Equipment Manual)

Number

Designation
Make (e. g.)
Order number

WH58.30-Z-1007-16A
Engine oil extractor
Deutsche Tecalemit

Am Metallwerk 11

33659 Bielefeld

1.386950.2

P18.00-0019-01

Shown on Engine 104

1
Extract engine oil through the dipstick guide tube.

Perform only when engine is at normal operating temperature.

Copyright DaimlerChrysler AG 20.05.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1

AF54.30-P-8400A
Instrument cluster indicates: Oil sensor defective, oil level below min. or oil level

above max. with engine running and at operating temperature. No DTC stored.
19.5.98

MODEL
129.0, 163.1, 202.0, 208.3 /4, 210.0 /2 /6, 220.0 /1 with ENGINE 112

MODEL
129.0, 163.1, 202.0, 208.3 /4, 210.0 /2, 220.0 /1 with ENGINE 113

Damage code
Cause
Remedy

54 201 90
Oil low, connector defective or coding error
1
Shut off engine and wait 2 min. (key

position 0)

Instrument cluster indicates oil sensor

defective, oil level below min. or oil level

above max. with engine warm and running.

No DTC stored in DTC memory!

2
Check oil level with oil dipstick

3
Check oil level on instrument cluster:

- Key in steering wheel lock position 2,

engine not running

- Wait until - - - - - - appears on

instrument cluster

- When this is displayed press the reset

button for the tripodometer twice within

1 sec. (display appears only after

expiration of a waiting time (max. 30

min.) depending on engine oil

temperature)

Oil level is at bottom mark on oil dipstick

and instrument cluster indicates:
-1L
, -
1,5L
or -2L
#
4
Add quantity of oil indicated on

instrument cluster display and repeat

test.

Oil level at upper mark on dipstick and

instrument cluster indicates either oil level

okay or -1L
, -
1,5L
, -2L

#
5
Recode instrument cluster

AF54.30-P-8600A

Problem still present
#
6
Check cable to oil sensor, oil sensor
connectors, control module and fuse

box (see wiring diagram) for good contact

Copyright DaimlerChrysler AG 05.06.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1

1998-2005 SUSPENSION
Suspension - 163 Chassis
GENERAL INFORMATION
GENERAL NOTES ON WORKING ON VEHICLES WITH LEVEL CONTROL/ADS - AH32.00-P-0002-01A
All models with code 216b, 216c, 217a, 480
Fig. 1: Identifying Box Wrench (116 589 00 17 00)

The following instructions should be followed when disconnecting and connecting pressure lines:
Clean contaminated line connections before disconnecting them. Seal disconnected lines and hoses and
connections to components immediately with blind plugs.
Only use open box wrench and special tool when loosening and tightening pressure lines to avoid damage to the
line connections.
Check the component concerned and line connections for leaks after assembly work on the suspension
system.
NOTES ON CHECKING OIL LEVEL ON VEHICLES WITH LEVEL CONTROL/ADS - AH32.00-P-0003-01A
All models with SA Code 217a/ 480
Observe the following prerequisites when checking the oil level in the oil reservoir:
1. The vehicle must be standing on its wheels.
2. Check the oil level when the vehicle is ready to drive:
Vehicle ready for use with oil and coolant reservoirs filled.
Full fuel tank - compensate for any missing fuel by placing additional weight in trunk.
Spare wheel and vehicle tool kit in vehicle.
Unladen vehicle. Remove any luggage, fuel canisters etc. from the vehicle.
On vehicles with level control /ADS, the oil level in the oil reservoir may fall below the "min." mark
on the oil dipstick when the vehicle is loaded.

2001 Mercedes-Benz ML320
1998-2005 SUSPENSION Suspension - 163 Chassis

2001 Mercedes-Benz ML320
1998-2005 SUSPENSION Suspension - 163 Chassis
me
Saturday, October 02, 2010 3:37:35 PMPage 1 © 2006 Mitchell Repair Information Company, LLC.
me
Saturday, October 02, 2010 3:37:38 PMPage 1 © 2006 Mitchell Repair Information Company, LLC.