fuse MERCEDES-BENZ ML350 1997 Complete Repair Manual

AD54.30-P-6000-01GH
Instrument cluster, testing electrical system IC
Model 163

t
A

Scope of test

Measuring instrument/

Test connection

Operation/

Requirement
Specified value
D
Possible cause/

Remedy

1.0Instrument cluster (A1)


Voltage supply,

terminal 30

3 w

(A.3)

A1

cL
11

(A.11)

Ignition:
OFF

Remove A1

Coupling "A" (18-pin)

disconnected

11
-
14 V
D
Fuse f13 in fuse and relay

box F1

D
Cables

Value in order
#
t
1.1

1.1
Voltage supply,

terminal 15

3 w

(A.3)

A1

cL
9

(A.9)

Ignition: ON
11
-
14 V

D
Fuse f22 in fuse and relay

box F1

D
Cables

Value in order
#
t
1.2

1.2
Voltage supply,

terminal 15R

3 w

(A.3)

A1

cL
7

(A.7)

Ignition: ON
11
-
14 V

D
Fuse f10 in fuse and relay

box F1

D
Cables

Value in order
#
D
A1

Copyright DaimlerChrysler AG 05.06.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1

AF54.30-P-8400A
Instrument cluster indicates: Oil sensor defective, oil level below min. or oil level

above max. with engine running and at operating temperature. No DTC stored.
19.5.98

MODEL
129.0, 163.1, 202.0, 208.3 /4, 210.0 /2 /6, 220.0 /1 with ENGINE 112

MODEL
129.0, 163.1, 202.0, 208.3 /4, 210.0 /2, 220.0 /1 with ENGINE 113

Damage code
Cause
Remedy

54 201 90
Oil low, connector defective or coding error
1
Shut off engine and wait 2 min. (key

position 0)

Instrument cluster indicates oil sensor

defective, oil level below min. or oil level

above max. with engine warm and running.

No DTC stored in DTC memory!

2
Check oil level with oil dipstick

3
Check oil level on instrument cluster:

- Key in steering wheel lock position 2,

engine not running

- Wait until - - - - - - appears on

instrument cluster

- When this is displayed press the reset

button for the tripodometer twice within

1 sec. (display appears only after

expiration of a waiting time (max. 30

min.) depending on engine oil

temperature)

Oil level is at bottom mark on oil dipstick

and instrument cluster indicates:
-1L
, -
1,5L
or -2L
#
4
Add quantity of oil indicated on

instrument cluster display and repeat

test.

Oil level at upper mark on dipstick and

instrument cluster indicates either oil level

okay or -1L
, -
1,5L
, -2L

#
5
Recode instrument cluster

AF54.30-P-8600A

Problem still present
#
6
Check cable to oil sensor, oil sensor
connectors, control module and fuse

box (see wiring diagram) for good contact

Copyright DaimlerChrysler AG 05.06.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1

MODEL 129, 163, 170, 202, 208, 210 as of 1.6.98,215, 220 with CODE (231a) Garage door opener
GARAGE DOOR OPENER DIAGNOSIS, FUNCTION CHECK - AD68.05-P-3000A
MODEL 129, 163, 170, 202, 208, 210 as of 1.6.98,215, 220 with CODE (231a) Garage door opener
GARAGE DOOR OPENER DIAGNOSIS, TROUBLE-SHOOTING - AD68.05-P-5000A
MODELS 129, 163, 170, 202, 208, 210 as of 1.6.98,215, 220 with CODE (231a) Garage door opener
Garage door opener locationModels 129, 202, 208, 210, 215, 220GF68.05-P-1100-01A
Model 170GF68.05-P-1100-01B
Model 163GF68.05-P-1100-01C
Electrical wiring diagramsModel 163PE68.00-P-1100D
Model 170PE68.00-P-1100C
Models 202, 208PE68.00-P-1100B
Model 210PE68.00-P-1100A
Model 220PE68.00-P-1100SA
Model 129, volume 2, FG 68
Connection and use of test equipment AD00.00-P-1000AZ
Diagnostic tools, garage door opener AD68.05-P-2000-01A
Compatibility test for garage door opener AD68.05-P-2000-02A
Garage door opener diagnosis, previous knowledge AD68.05-P-
2000A
Key to diagnostic symbols AD00.00-P-
2001A

Fuses in order
Battery voltage 11-14V
Ignition: ON

Function check
Scope of test Operation / requirement Specified value Possible
cause / remedy
1
Transmitting

push-button
The desired transmitting push-button is programmed.
The vehicle is inside the garage door range.
The garage door opener signal has a range of at least
85% of the range of the garage door hand transmitter or
15m.
Press programmed transmitting push-button.
Garage door is
activated.AD68.05-P-
5000A

Garage door opener
diagnosis, previous
knowledge
AD68.05-P-2000A

2001 Mercedes-Benz ML320
1998-2005 ACCESSORIES & BODY, CAB Interior Equipment - 163 Chassis
me
Saturday, October 02, 2010 3:35:21 PMPage 10 © 2006 Mitchell Repair Information Company, LLC.

Fuses in order.
Battery voltage
11-14 V
Ignition: ON

Troubleshooting
Complaint Possible cause Note Remedy
The garage door
cannot be
activated with the
garage door
opener installed
in the vehicle.
The garage door opener
has not been
programmed correctly.
GF68.05-P-0001A
The garage door is
defective
Check garage door: Activate
the garage door with the
hand transmitter. If the
garage door cannot be
opened and closed with the
hand transmitter, the garage
door has a mechanical or
electrical defect.

The garage door's
receiver and the garage
door opener installed in
the vehicle are not
compatible.
A list of compatible garage
doors is included in the
passenger car sales manualIf the used garage door is not
listed check compatibility
with compatibility tester.

Compatibility check of
electrical system for garage
door opener Models 129, 170,
202, 208, 210 as of 1.6.98, 163
as of 1.9.01, 215, 220 with
CODE (231a) garage door
opener Compatibility check for
garage door opener.
AD68.05-P-6000-02A
AD68.05
-P-2000-02A

Voltage supply to
garage door opener
interrupted.Model 208 as of 1.6.98, except
CODE (249a)
Automatic dimming inside
rearview mirror
AD68.05-P-6000-01A

Model 202 as of 1.6.98, Model
210 as of 1.6.98, except CODE
(249a)
Automatic dimming inside
rearview mirror
AD68.05-P-6000-01C
Model 202 as of 1.6.98, Model
208 as of 1.6.98, Model 210 as
of 1.6.98, with CODE (249a) AD68.05-P-6000-01G

2001 Mercedes-Benz ML320
1998-2005 ACCESSORIES & BODY, CAB Interior Equipment - 163 Chassis
me
Saturday, October 02, 2010 3:35:21 PMPage 11 © 2006 Mitchell Repair Information Company, LLC.

MODELS 129, 163, 170, 202, 208, 210 as of 1.6.98,215, 220 with CODE (231a) Garage door opener
TESTING & REPAIR
TESTING AND REPAIR WORK: PASSENGER CARS: INTERIOR EQUIPMENT - AR68.00-Z-9163AA
MODEL 163
Garage door opener diagnosis,
previous knowledge AD68.05-P-
2000A
Fuses in order.
Battery voltage 11-14 V

Checking
1Compatibility check of electrical
system for garage door openerModels 129, 170, 202, 208, 210 as of 1.6.98,
163 as of 1.9.01,
215, 220 with CODE (231a) garage door openerAD68.05-P-
6000-02A
2Voltage supply for test of electrical
system for garage door openerModel 208 as of 1.6.98, except CODE (249a)
Automatic dimming inside rearview mirrorAD68.05-P-
6000-01A
3Voltage supply for test of electrical
system for garage door openerModel 129 as of 1.6.98AD68.05-P-
6000-01B
4Voltage supply for test of electrical
system for garage door openerModels 202, 210 as of 1.6.98, except CODE
(249a) Automatic dimming inside rearview
mirrorAD68.05-P-
6000-01C
5Voltage supply for test of electrical
system for garage door openerModel 170 as of 1.6.98AD68.05-P-
6000-01D
6Voltage supply for test of electrical
system for garage door openerModel 163 as of 1.6.98AD68.05-P-
6000-01E
7Voltage supply for test of electrical
system for garage door openerModels 215, 220AD68.05-P-
6000-01F
8Voltage supply for test of electrical
system for garage door openerModels 202, 208, 210 as of 1.6.98, with CODE
(249a) Automatic dimming inside rearview
mirrorAD68.05-P-
6000-01G
Removing and installing
instrument panelMODEL 163.113 /128 /136 /154 /157 /172 /174 /175AR68.10-P-
1000GH
Remove/install center section of
instrument panelMODEL 163.113 /128 /136 /154 /157 /172 /174 /175AR68.10-P-
1030GH
Remove/install bottom section of
instrument panelMODELS 163.113 /128 /136 /154 /157 /172 /174 /175AR68.10-P-
1040GH
Removing and installing side air
nozzleMODELS 163.113 /128 /136 /154 /157 /172 /174 /175AR68.10-P-
1100GH
Remove/install instrument panel
carrierMODEL 163.113 /128 /136 /154 /157 /172 /174 /175AR68.10-P-
1111GH
Removing and installing center AR68.10-P-

2001 Mercedes-Benz ML320
1998-2005 ACCESSORIES & BODY, CAB Interior Equipment - 163 Chassis
me
Saturday, October 02, 2010 3:35:21 PMPage 13 © 2006 Mitchell Repair Information Company, LLC.

Fig. 59: Identifying Paneling In Footwell
REMOVING AND INSTALLING PANELING ON A-PILLAR - AR68.30-P-4050GH
MODELS 163.113 /128 /136 /154 /157 /172 /174 /175
Vehicle illustrated up to 31.8.98

Remove/install
1Remove front door sill molding cover (1)
2Unscrew screws from door sill molding on rocker panel Only two front screws.
3Pull off door seal (2) in the area of driver's side paneling (3) or
front passenger's side paneling (4)
4Unscrew screw (5) for engine hood release lever (6) on A-pillar Driver's side only.
5Unhook engine hood cable and remove engine hood release
lever (6) Driver's side only.
6.1Rotate locks (7) on the cover of the fuse and relay box (8) 1/4
revolution counterclockwise into the vertical position As of 09.99. Passenger
side only.
7.1Pull back cover of fuse and relay box (8) (arrow) and remove As of 09.99. Passenger
side only.
8.1Unscrew nut (9) As of 09.99. Passenger
side only.
9Unclip driver's side paneling (3) and front passenger's side
paneling (4) and remove Lift door sill molding
slightly to allow removal.
10Install in the reverse order

2001 Mercedes-Benz ML320
1998-2005 ACCESSORIES & BODY, CAB Interior Equipment - 163 Chassis
me
Saturday, October 02, 2010 3:35:22 PMPage 58 © 2006 Mitchell Repair Information Company, LLC.

GF77.20-P-2003GH
Opening pop-up roof, function
19.2.97

MODEL
163 with CODE (414a) Electric glass sliding/pop-up roof

Function prerequisites

D
Voltage not too low or too high

D
Switch-on conditions for convenience control fulfilled

D
Sliding/pop-up roof synchronized

Function

When
switch (SHD, S13/2)
is actuated continuously, circuit 30 is

switched through to the
sliding/pop-up roof (M12)
and the pop-up

roof opens.

The function "Open pop-up roof" is executed as long as

D
switch (SHD, S13/2)
is actuated and

D
the pop-up roof has not yet reached the end position and

D
lock-up is not recognized.


If the sliding/pop-up roof is desynchronized, it moves only in the pop-

up roof direction each time the
switch (SHD, S13/2)
is actuated. This
means that it is possible to move to the zero
position for synchronizing. After successful

synchronization
, the

sliding/pop-up roof can be controlled again without limitation.

Vehicles
up to 11.99:

The power for the
sliding/pop-up roof (M12)
is supplied via a

fuse directly to c. 30.

The power for the
switch (SR, S13/2)
is supplied via the

convenience relay (F1k14)
, which is actuated by the all-

activity module (AAM, N10).

Vehicles
as of 12.99:

The power for the
sliding/pop-up roof (M12)
is supplied via a

fuse directly to c. 30. The power for the
switch (SHD, S13/2) is

supplied via a lead to the
extended-activity module (EAM,

N10/1) , this power is switched through only when the switch-on

conditions for the convenience control are fulfilled and the EAM

is coded accordingly.


Closing sliding /pop-up roof, function

GF77.20-P-2002GH


Sliding /pop-up roof lock-up recognition,
function

GF77.20-P-3000GH


Sliding /pop-up roof position measurement,

function

GF77.20-P-3001GH


Synchronizing sliding /pop-up roof, function

GF77.20-P-3002GH


Convenience control

GF72.29-P-2002GH


All-activity module (AAM)
up to 11.99

GF54.21-P-4100GH

Extended-activity module, location/

purpose/design/function
as of 12.99

GF54.21-P-4107GK

Copyright DaimlerChrysler AG 04.08.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1

9
Detach return line (30f) and high-pressure

expansion hose (30i)

Connection fittings or banjo bolts

depending on the version. Seal off line

connections with plugs.


Installation:
Replace sealing rings.


Connection fitting, return line

*BA46.20-P-1001-01D

Connection fitting, high-pressure

expansion hose

*BA46.20-P-1002-01D

Banjo bolt, return line

*BA46.20-P-1004-01D

Banjo bolt, high-pressure expansion hose

*BA46.20-P-1005-01D

Plug

*129589009100

10
Detach nut (25d) and bolt from steering

coupling (25) and pull lower steering shaft

(80a) upwards out of steering coupling (25)

Do not use force as the corrugated tube is

sensitive to lateral forces. Enlarge clamping

groove a little with a screwdriver if necessary.


Installation:
Replace nut (25d).


Installation:
Turn rack-and-pinion

steering to center position and fit steering

coupling.

AR46.20-P-0600-01GH


*BA46.10-P-1001-01D

11
Detach rack-and-pinion steering (23) from

front axle carrier (1) by unscrewing bolts (23a)

The installed position of the shims (23h,

23i) on the right-hand side, between the

rubber mount and the front axle carrier, must

be observed as the shims are of different

thicknesses.


Installation:
Attach rack-and-pinion

steering to front axle carrier.

AR46.20-P-0600-03GH


Assessing condition of steering gear when

repairing accident vehicles

AH46.20-P-9409-01A

12
Check rubber mount (21) of rack-and-pinion

steering mounting for damage
Replace rubber mount if necessary:
#

Removing rubber mounts on rack-and-pinion

steering mounting

AR46.20-P-0600-02GH

13
Install in the reverse order

14
Fill and bleed power steering pump
Engines 112, 113

AR46.30-P-0010B
Engines 111, 612, 628
AR46.30-P-0010P

15
Check steering for function and leaks

There is a grease cushion under the cover
cap. A small amount of escaping grease is to

be regarded as normal and must not be

confused with leakage.

16.1
Check toe on front axle and adjust if necessary
When installing a new rack-and-pinion

steering, see:

#

Performing chassis alignment check

AR40.20-P-0200A


Steering shaft

Number

Designation
Model 163

BA46.10-P-1001-01D
Self-locking nut, steering coupling to steering shaft

and rack-and-pinion steering
Nm
28


Steering gear

Number

Designation
Model 163

BA46.20-P-1001-01D
Screwed connection fitting from return line

to rack-and-pinion steering
Nm
15

BA46.20-P-1002-01D
Screwed connection fitting from high-

pressure expansion hose to rack-and-pinion

steering
Nm
15

BA46.20-P-1003-01D
Bolted connection, rack-and-pinion steering

to front axle carrierNm
50

BA46.20-P-1004-01D
Banjo bolt, return line to rack-and-pinion

steering
Nm
30

BA46.20-P-1005-01D
Banjo bolt, high-pressure expansion hose to

rack-and-pinion steering
Nm
30

Copyright DaimlerChrysler AG 06.07.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 2

2001-04 STARTING & CHARGING SYSTEMS Starters - 163 Chassis
MODEL IDENTIFICATION
MODEL IDENTIFICATION
DESCRIPTION
Starter is a brush-type, series-wound el ectric motor with an overrunning clutch. Field frame contains field coils
and is enclosed by commutator/drive bushing end frame, which carries pole shoes. A splined armature shaft
carries drive assembly.
TROUBLE SHOOTING
BASIC TROUBLESHOOTING
If starter is noisy, the cause could be bent or damaged gear tooth chamfers on ring gear. This cannot be seen
with starter installed in ve hicle. Activate starter without switching ignition on. Me tallic noise should not be
heard. If noise is he ard, replace ring gear.
PRELIMINARY INSPECTION
Verify customer complaint by operating system. Visually inspect for obvious signs of mechanical and electrical
damage. Check generator belt tension and condition. Ensure that battery voltage is within specifications. Inspect
for blown fuses and damaged relays. For fuse and/or relay identification, see WIRING DIAGRAMS
.
WARNING:
Vehicles are equipped with air bag supplemental restraint system. Before
attempting any repairs involving steer ing column, instrument panel or
related components, see SERVICE PRECAUTIONS (or AIR BAG SAFETY
PRECAUTIONS) and DISABLING & ACTIVATING AIR BAG SYSTEM in
appropriate AIR BAG REST RAINT SYSTEMS article.
NOTE: When the battery is di sconnected, vehicle computer and memory system may
lose data. Driveability problems may exist until computer systems have
completed a relearn cycle. Radio will not operate until coded. Obtain code card
from customer.
NOTE: The following table identifies mo dels applicable to this article.
ModelChassisEngine Number
ML430 (2001)163.172113.942
ML320 (2001-03)163.154112.942
ML55 AMG (2001-03)163.174113.981
ML500 (2002-04)163.175113.965
ML350 (2003-04)163.157112.970

2001 Mercedes-Benz ML320
2001-04 STARTING & CHARGING SYSTEMS Starters - 163 Chassis

2001 Mercedes-Benz ML320
2001-04 STARTING & CHARGING SYSTEMS Starters - 163 Chassis
me
Saturday, October 02, 2010 3:19:47 PMPage 1 © 2006 Mitchell Repair Information Company, LLC.
me
Saturday, October 02, 2010 3:19:50 PMPage 1 © 2006 Mitchell Repair Information Company, LLC.