fold seats MERCEDES-BENZ ML350 1997 Complete Owner's Guide

AR91.12-P-1010GI
Remove and install bench
21.3.00

MODELS
163.136 /154 /172 as of 1.9.99,

163.113 /128 /157 /174 /175

40 % bench seat

P91.12-2126-06

1
Bolts, front of rear seat fastening

2
Bolts, rear of rear seat fastening

4
Seat frame covering


Remove, Install

1
Remove headrest

See Operating Instructions

2.1
Remove covering (4) on bottom of rear seat

On 40 % rear seat only.

AR91.12-P-1100GH
3.1
Disconnect plug to seat belt buckle cable

Only with side airbag in the rear (left and

right), code 293.

4.1
Remove electric lead attached to seat frame

with adhesive tape

Only with side airbag in the rear (left and

right), code 293.


Installation:
Replace adhesive tape.

5
Unscrew bolts (1) on front of rear seat

fastening


Installation:
Replace bolts and nuts with

locking agent applied.

Torx bit set

*000589011000


*BA91.12-P-1005-03A

6
Release backrest and tip forward

See Operating Instructions

7
Release seat bench and fold down

See Operating Instructions

8
Remove bolts (2) on rear of rear seat fastening


Installation:
Replace bolts and nuts with

locking agent applied.

Torx bit set

*000589011000


*BA91.12-P-1005-03A

9
Remove 40 % bench

10
Install in the reverse order


Rear seats

Number

Designation
Model

163 as of

09/99

BA91.12-P-1005-03A
Nuts for rear seat console on vehicle floor
NM
40

Copyright DaimlerChrysler AG 12.06.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1

AZ91.20-P-0001A
Retrofitting anchor rings for child seat restraint attachments
14.11.00

MODEL
163.113 /136 /154 /172 /174

P91.20-2039-06

2
Anchor mounting plate

3
Long spacer

4
Short spacer

5
Trim plate

6
Anchor ring

7
Long bolt

8
Short bolt

9
Trim cover

P91.20-2040-01

1
Template

12
Bolt location for

mounting plate

13
Rivet locations for

mounting plate
Hole in carpet,

Ø=57 mm

10
Center hole for

anchor ring, Ø=9.5

mm

11
Hole for rivet, Ø=4

mm

P91.20-2038-01


Removing

1
Remove compact spare tire

See Owner's Manual.

2
Fold 3rd row seats to storage position

Only with code (847). See Owner's Manual.

3
Remove footwell covers

See Owner's Manual.

4
Remove cargo anchor rings

Modifying

5
Place template (1) on top of load

compartment floor covering and secure with

cargo anchor bolts (arrows)

Turn template over for opposite side.

Template

*163589066300

6
Mark floor covering through center of bolt

location (12) for anchor mounting plate (2)

Only for those positions at which anchor

rings will be installed.

7
Remove template (1)

8
Remove load compartment floor covering

f

AR68.20-P-4810GH

9
Place floor covering faceup on suitable surface

10
Using hole saw, create Ø=57 mm hole for

anchor ring assembly


Only for those positions at which anchor

rings will be installed. Secure floor covering

appropriately to ensure hole is cut cleanly.

Use mark as a guide for center of hole.

11
Lower rear axle carrier

Only Model 163.174 for installation of 2nd

row center anchor ring.

f

AR35.10-P-0020-01GH

12
Place template (1) on floor pan and secure

with cargo anchor bolts

Copyright DaimlerChrysler AG 14.06.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1

AR91.12-P-1730GI
Remove and install locking mechanism for folding rear seat backrest
5.5.99

MODELS
163.136 /154 /172 as of 1.9.99,

163.113 /128 /157 /174 /175

P91.12-2133-06

1
Rear backrest release cable

2
Adjuster

3
Screws

4
Bolts

5
Rear backrest fitting


Remove/Install

1
Remove side covers at rear backrest

fitting (5)

2
Detach rear seat backrest release cable (1) at

adjuster (2)

Mark adjustment position on the thread.

Turn the adjuster counterclockwise until the

rear backrest release cable can be unhooked.

3
Unscrew bolts (3) from rear backrest fitting


With 60% rear seat:
Unscrew bolts (3) at
the same time in order to prevent the rear

backrest fitting from tipping.


*BA91.12-P-1006-03A

4
Unscrew bolts (4) from rear backrest fitting


*BA91.12-P-1007-03A

Torx bit set

*000589011000

5
Remove backrest fitting (5)

6
Install in the reverse order


Installation:
check unlocking function of

folding rear backrest.


Rear seats

Number

Designation
Model

163 as of

09/99

BA91.12-P-1006-03A
Bolt from backrest fitting to backrest
Nm
30

BA91.12-P-1007-03A
Screw for backrest fitting on seat frame
Nm
30

Copyright DaimlerChrysler AG 14.06.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1