spare tire MERCEDES-BENZ ML350 2006 W163 User Guide
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2006, Model line: ML350, Model: MERCEDES-BENZ ML350 2006 W163Pages: 539, PDF Size: 3.77 MB
Page 371 of 539
370 OperationWinter driving
Block heater (Canada only)
The engine is equipped with a block
heater.
The electrical cable may be installed at an
authorized Mercedes-Benz Light Truck
Center.Snow chains
Snow chains should only be driven on
snow-covered roads at speeds not to
exceed 30 mph (50 km/h). Remove chains
as soon as possible when driving on roads
without snow.Please observe the following guidelines
when using snow chains:
Use of snow chains is not permissible
with all wheel/tire combinations.
Snow chains should only be used on
the rear wheels. Follow the manufac-
turer’s mounting instructions.
Only use snow chains that are
approved by Mercedes-Benz. Your
authorized Mercedes-Benz Light Truck
C e n t e r w i l l b e g l a d t o a d v i s e y o u o n t h i s
subject.
Use of snow chains may be prohibited
depending on location. Always check
local and state laws before installing
snow chains.
Warning!
G
If you use your spare tire when winter tires
are fitted on the other wheels, be aware that
the difference in tire characteristics may
very well impair turning stability and that
overall driving stability may be reduced.
Adapt your driving style accordingly.
Have the spare tire replaced with a winter
tire at the nearest authorized
Mercedes-Benz Light Truck Center.
iWhen driving with snow chains, you
may wish to deactivate the ESP
®
(
page 97) before setting the vehicle
in motion. This will improve the
vehicle’s traction.
!Even on vehicles with all-wheel-drive
use snow chains on rear tires only.
The use of snow chains is not permissi-
ble with the spare wheel.
Page 393 of 539
392 Practical hintsWhat to do if …Warning!
G
Each tire, including the spare (if provided),
should be checked monthly when cold and
inflated to the inflation pressure recom-
mended by the vehicle manufacturer on the
vehicle placard or the tire inflation pressure
label. (If your vehicle has tires of a different
size than the size indicated on the vehicle
placard or the tire inflation pressure label,
you should consult the appropriate section
of this owner’s manual to determine the
proper tire inflation pressure). When the low
tire pressure telltale is illuminated, one or
more of your tires is significantly under-in-
flated. You should stop and check your tires
as soon as possible, and inflate them to the
proper pressure. Driving on a significantly
under-inflated tire causes the tire to over-
heat and can lead to tire failure. Under-infla-
tion also reduces fuel efficiency and tire
tread life, and may affect the vehicle’s han-
dling and stopping ability.
Your vehicle has also been equipped with a
TPMS malfunction telltale to indicate when
the system is not operating properly. When
the malfunction telltale is illuminated, the
system may not be able to detect or signal
low tire pressure as intended. TPMS mal-
functions may occur for a variety of reasons,
including the installation of incompatible
replacement tires on the vehicle. Always
check the TPMS malfunction telltale after
replacing one or more tires on your vehicle
to ensure that the replacement tires are
compatible with the TPMS.
Page 407 of 539
406 Practical hintsWhat to do if …Display message
Possible cause
Possible solution
Tire pressure display
appears after driving
several minutes
The tire inflation pressure is being checked.
Drive the vehicle for a few minutes.
Tire pressure monitor
inoperative
The Advanced TPMS* is malfunctioning.
Have the Advanced TPMS* checked by an autho-
rized Mercedes-Benz Light Truck Center.
Tire pres. monitor
inoperative
No wheel sensors
There are wheels without wheel sensors
mounted (e.g. winter tires).
Have the Advanced TPMS* checked by an autho-
rized Mercedes-Benz Light Truck Center.
Have the wheel sensors install by an authorized
Mercedes-Benz Light Truck Center.
Tire pres. monitor
Wheel sensor missing
One or more sensors defect (e.g. battery in
one or more wheel sensor is empty).
One or more wheels without wheel sensors
mounted (e.g. spare tire).
Have the Advanced TPMS* checked by an autho-
rized Mercedes-Benz Light Truck Center.
Have the wheel sensors install by an authorized
Mercedes-Benz Light Truck Center.
The tire pressure for the respective tire is not shown
in the multifunction display.
Tire pres. monitor
temporarily
unavailable
The Advanced TPMS* is unable to monitor
the tire pressure due to
a nearby radio interference source.
excessive wheel sensor temperatures.
As soon as the causes of the malfunction have been
removed, the Advanced TPMS* automatically be-
comes active again after a few minutes driving.
Page 435 of 539
434 Practical hintsWhere will I find ...?
Loosen retaining screw3 by turning it
counterclockwise.
Remove Minispare wheel1.
Use the Minispare wheel only temporarily,
while observing the following restrictions:
Do not exceed vehicle speed of
50 mph (80 km/h).
Drive to the nearest repair facility to
have the flat tire repaired or replaced
as appropriate.
Do not operate vehicle with more than
one Minispare wheel mounted.iPlease comply with the instructions for
“Mounting the spare wheel”
(page 457).
Page 457 of 539
456 Practical hintsFlat tire
Preparing the vehicle
Park the vehicle as far as possible from
moving traffic on a hard surface.
Turn on the hazard warning flashers.
Turn the steering wheel so that the
front wheels are in a straight ahead po-
sition.
Set the parking brake.
Shift automatic transmission to park
positionP.
Vehicles with Air suspension package*:
Do not open or close a door or tailgate
while mounting the spare wheel.
Vehicles with SmartKey:
Turn off the engine (
page 34).
Remove the SmartKey from the starter
switch.Vehicles with KEYLESS-GO*:
Turn off the engine by pressing the
KEYLESS-GO* button once
(page 63).
Open the driver’s door (this puts the
starter switch in position0, same as
with the SmartKey removed from the
starter switch). The driver’s door then
can be closed again.
Have any passenger exit the vehicle at
a safe distance from the roadway.
Warning!
G
The dimensions of the Minispare wheel are
different from those of the road wheels. As
a result, the vehicle handling characteristics
change when driving with a mounted
Minispare wheel. Adapt your driving style
accordingly.
The Minispare wheel is for temporary use
only. When driving with a Minispare wheel
mounted, ensure proper tire pressure and
do not exceed a vehicle speed of
50 mph (80 km/h).
Drive to the nearest Mercedes-Benz Light
Truck Center as soon as possible to have the
Minispare wheel replaced with a regular
road wheel.
Never operate the vehicle with more than
one spare wheel mounted.
Do not switch off the ESP
® when a
Minispare wheel is mounted.
iOpen doors only when conditions are
safe to do so.
Page 458 of 539
457 Practical hints
Flat tire
Mounting the spare wheel
Preparing the vehicle
Prepare the vehicle as described
(page 456).
Take the wheel wrench, the collapsible
wheel chock, and the vehicle jack out
of the cargo compartment
(page 430).
Take the Minispare wheel out of the
cargo compartment (
page 433).Lifting the vehicle
Prevent the vehicle from rolling away
by blocking wheels with wheel chocks
or other sizable objects.
A collapsible wheel chock is included
with the vehicle tool kit (
page 430).
For information on setting up the col-
lapsible wheel chock, see
(
page 432).
When changing wheel on a level surface:
Place one wheel chock in front of and
another sizeable object behind the
wheel that is diagonally opposite to the
wheel being changed.
Always try lifting the vehicle using the jack
on a level surface. However, should
circumstances require you to do so on a
hill, place the wheel chock and other size-
able object as follows:
Place the wheel chock and another
sizable object on the downhill side
blocking both wheels of the axle not
being worked on.
!Vehicles with factory-mounted
running-boards*:
Your vehicle is equipped with a scis-
sors-type jack (located under the cargo
compartment floor) designed for use
with factory-mounted running boards.
Only use this jack when jacking up ve-
hicles with factory-mounted running
boards as otherwise the vehicle’s
underbody can be damaged. See sepa-
rate instructions for scissors-type jack.
Warning!
G
The jack is designed exclusively for jacking
up the vehicle at the jack take-up brackets
built into both sides of the vehicle. To help
avoid personal injury, use the jack only to lift
the vehicle during a wheel change. Never
get beneath the vehicle while it is supported
by the jack. Keep hands and feet away from
the area under the lifted vehicle. Always
firmly set parking brake and block wheels
before raising vehicle with jack.
Do not disengage parking brake while the
vehicle is raised. Be certain that the jack is
always vertical (plumb line) when in use, es-
pecially on hills. Always try to use the jack
on level surface. Make sure that the jack
arm is fully seated in the jack take-up brack-
et. Always lower the vehicle onto sufficient
capacity jackstands before working under
the vehicle.
Page 460 of 539
459 Practical hints
Flat tire
Removing the wheel
1Alignment bolt
Unscrew upper-most wheel bolt and
remove it.
Replace this wheel bolt with alignment
bolt1 supplied with the tool kit
(page 430).
Remove the remaining bolts.
Remove the wheel.Mounting the new wheel
1Wheel bolt for 18" and 19" light alloy
rims*
2Wheel bolt for 17" light alloy rims or
Minispare wheel (located in vehicle tool
kit (
page 431))
Warning!
G
The jack is intended only for lifting the
vehicle briefly for wheel changes. It is not
suited for performing maintenance work
under the vehicle.
Never start the engine when the vehicle
is raised.
Never lie down under the raised vehicle.
!Do not place wheel bolts in sand or dirt.
This could result in damage to the bolts
and wheel hub threads.
!Wheel bolts2 must be used when
mounting 17" light alloy rims or the
Minispare wheel. The use of any wheel
bolts other than wheel bolts2 for
17" light alloy rims or the Minispare
wheel will physically damage the vehi-
cle’s brakes.
Page 461 of 539
460 Practical hintsFlat tire
Clean contact surfaces of wheel and
wheel hub.
Guide spare wheel onto the alignment
bolt and push it on the wheel hub.
Insert wheel bolts and tighten them
slightly.
Unscrew the alignment bolt.
Insert the remaining wheel bolt and
tighten it slightly.Lowering the vehicle
Lower vehicle by turning crank coun-
terclockwise until vehicle is resting ful-
ly on its own weight.
Remove the jack.
!To avoid paint damage, place wheel flat
against hub and hold it there while
installing first wheel bolt.Warning!
G
Always replace wheel bolts that are
damaged or rusted.
Never apply oil or grease to wheel bolts.
Damaged wheel hub threads should be
repaired immediately. Do not continue to
drive under these circumstances! Contact
an authorized Mercedes-Benz Light Truck
Center or call Roadside Assistance.
Incorrect wheel bolts or improperly tight-
ened wheel bolts can cause the wheel to
come off. This could cause an accident.
Make sure to use the correct wheel bolts.
Warning!
G
Use only genuine equipment
Mercedes-Benz wheel bolts. Other wheel
bolts may come loose.
Do not tighten the wheel bolts when the ve-
hicle is raised. Otherwise the vehicle could
fall off the jack.
Page 490 of 539
489 Technical data
Rims and tires
Minispare wheel
ML 350
ML 500
Rim
4.0B x 18 H2
Wheel offset
1.58 in (40 mm)
Tire
T 155/90-18 113M
1
1Must not be used with snow chains.!Please compare the recommended tire
inflation pressure for your vehicle with
the tire inflation pressure on the yellow
label located on the Minispare wheel
rim.
If the tire inflation pressure on the
yellow label on the Minispare wheel rim
differs from the values given in this
Operator’s Manual, inflate the tire to
the recommended tire inflation pres-
sure given on the yellow label on the
Minispare wheel rim.
iPlease note that the tire inflation
pressure of the Minispare tire differs
from the tire inflation pressure of the
road tires.
Inflate the Minispare tire to approxi-
mately 61 psi (4.2 bar).
Page 516 of 539
515 Index
Emergency operations
Closing tilt/sliding sunroof* 439
Locking the vehicle 436
Opening tilt/sliding sunroof* 439
Remote door unlock 288
Unlocking the vehicle 435
Emergency tensioning device see ETD
Emission control 321
Ending
A call (telephone*) 180
Engine
Message in the display 410
Starting 49
Starting with KEYLESS-GO* 50
Technical data 486
Turning off 62
Engine cleaning 376
Engine compartment
Hood 326
Main fuse box 478
Engine malfunction
indicator lamp 385, 410
Engine malfunction indicator
lamp (Canada only) 25
Engine malfunction indicator
lamp (USA only) 25Engine number 502
Engine oil 327, 495
Adding 331
Additives 495
Checking level 327
Checking with the
control system (ML 500 only) 328
Checking with the
oil dipstick (ML 350 only) 330
Consumption 327
Display messages 414–415
Messages in display 329, 414–415
Viscosity 502
ESP
®
25, 95, 502
Off-road-ESP
®
98
Switching off 97
Switching on 98
Warning lamp 387
ETD 502
Safety guidelines 70
ETD (Emergency tensioning device) 76
Exterior mirrors
Folding 197
Exterior rear view mirrors
Adjusting 44
Parking position* for 174F
Fastening the seat belts 46
First aid kit 430
Flat tire 456
Lowering the vehicle 460
Preparing the vehicle 457
Spare wheel 433
Flexible Service System PLUS
(FSS PLUS) 502
Floormats* 279
Fluid level
Automatic transmission 332
Fog lamp, rear
Switching on 142
Fog lamps
Replacing bulbs 443
Fog lamps, front
Messages in display 418
Replacing bulbs 445
Switching on 142
Folding
Exterior mirrors 197
Folding the backrest forward 261
4-ETS 98
Off-road - 4-ETS 99