spare tire MERCEDES-BENZ ML430 1997 Complete Workshop Manual

AP40.10-P-4054R
TIREFIT puncture sealing compound - check expiry date
11.6.01

MODEL
163, 168, 170

MODEL
171, 203, 209, 230, 240, 414 except CODE (669) Spare tire on steel rim

MODEL
209, 211.004 /006 /016 /023 /026 /028 /042 /043 /061 /065 /070 /080 /082 /083 /206 /216 /223 /226 /2 42 /243 /261
/265 /270 /280 /282 /283 /606 /616

except CODE (679) Spare tire in structural wheel design

except CODE (690) Compact spare tire as emergency wheel

MODEL
211.076/ 276

P40.10-2522-06

Model 170, 171, 203, 209, 230

Shown on model 230

1
Date of manufacture

2
Expiration date

3
Trunk floor paneling

P40.10-2530-05

Model 168

1
Date of manufacture

2
Expiration date

3
Trunk floor paneling

P40.10-2643-04

MODEL 211.0

1
Date of manufacture

2
Expiration date

3
Trunk floor paneling

Copyright DaimlerChrysler AG 06.07.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1

AR40.15-P-0080A
Remove/install wheel sensor
1.4.99

MODELS
210.074 /274 with CODE (475) Tire pressure indicator

MODELS
211 with CODE (475) Tire pressure indicator

MODELS
215 with CODE (475) Tire pressure indicator

MODELS
220 with CODE (475) Tire pressure indicator

MODELS
230 with CODE (475) Tire pressure indicator

MODELS
240 with CODE (475) Tire pressure indicator

P40.15-2077-06

1
Union nut

2
Spacer ring (2x45°)

3
Valve body

4
Pin

4
2 mm

5
Screw

a
Date of manufacture

b
Identcode

A69/1
Left front TPM [RDK] wheel sensor

A69/2
Right front TPM [RDK] wheel

sensor

A69/3
Left rear TPM [RDK] wheel sensor

A69/4
Right rear TPM [RDK] wheel sensor

A69/5
Spare wheel TPM wheel sensor


Remove

1
Detach tires

AR40.10-P-1030A

2
Unscrew union nut (1) and remove spacer

ring (2

B
45 °)

Counterhold valve body (3) using

installation tool for tire pressure monitor or pin

4
2 mm (4) in drill hole (arrow).


Installation tool for tire pressure monitor

*WH58.30-Z-1040-06A

3
Remove TPM wheel sensor
Left front tire pressure monitor wheel

sensor (A69/1), right front tire pressure

monitor wheel sensor (A69/2), left rear tire

pressure monitor wheel sensor (A69/3), right

rear tire pressure monitor wheel sensor (A69/4)

4
Unscrew bolt (5) and remove valve body (3).


Check

5
Carry out visual inspection

Do not remove the white filter surface on

the underside of the TPM wheel sensor. Do

not clean TPM wheel sensor with compressed

air, solvents, or detergents. Wipe off dirt with

a clean, lint-free cloth only.


Install new TPM wheel sensor if:

D
The white filter surface of the TPM wheel

sensor is damaged or dirty

D
Tire sealant was used

D
Damage can be seen

D
The TPM wheel sensor is more than 5

years old according to the date of

manufacture (a).


Install


Replace all valve parts.

Observe different valve versions.

6
Insert bolt (5) through the hole in the TPM

wheel sensor and screw on valve body (3)

approx. 3 turns.

When replacing the TPM wheel sensor,

pay attention to the correct transmission
frequency (433 MHZ or 315 MHZ).

7
Insert valve body (3) with TPM wheel sensor

into wheel rim so that the radial bore (arrow)

for countering points upwards.

Copyright DaimlerChrysler AG 06.07.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1

AP40.10-P-4050GH
Remove/install wheels, rotate if necessary
15.7.97

MODEL
163

1-5
Tightening sequence

P40.10-0004-01
P40.00-0208-01


Remove

Danger!

Lethal injuries
are possible if vehicle slips off

of lifting platform
Align vehicle between the columns of the

lifting platform and position the four support

plates
at the lifting platform support points

specified by the vehicle manufacturer.

AS00.00-Z-0010-01A



Comply with notes on tires / rims

AH40.10-P-9411-01A

1
Raise vehicle.

AS00.00-Z-0010-01A

2
Unscrew wheel bolts, remove wheels

3
Check wheel bolts


The round contact shoulders on the lug

bolts must be free of oil and grease.

Replace bolts that have a damaged thread,

worn dacromet coating at radius seat or

corroded radius seat.

4
Check tires for damage and wear - measure

depth of tread

AP40.10-P-4051Z

5
Check disk wheels
D
check for contamination,

D
check that spherical caps are free of oil

and grease,

D
check centering, spherical caps and rim

flanges for damage,

D
check corrosion of lay-on surface

6
Check front wheel hub, brake disk bowl at

attachment face for contamination and

corrosion
Clean corroded surfaces with a wire brush or

an emery cloth.


Install

7
Change wheels around if necessary retaining

the same running direction


This excludes vehicles with mixed tires at

the front and rear axle.

Between

5,000 and 10,000 km according to wear.

8
Fit wheels, tighten wheel bolts

Observe tightening sequence "1-5".


*BA40.10-P-1001-01A


*126589040900

9
Lower vehicle, correct tire inflation pressure

(including spare wheel)


In the case of loss of tire pressure,

determine cause and replace tire if necessary.

On versions with spare tire attached to

underside of vehicle, check tire inflation

pressure of spare tire before lowering the

vehicle.

c
Deletion of spare tire with model 163.174

with TIREFIT

AH40.10-P-0001-01A


Wheels

Number

Designation
Models

163.113/128/
136/154/157/

172/175
Model

163.174

Copyright DaimlerChrysler AG 06.07.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1