Gear shift MERCEDES-BENZ ML500 2007 W163 Comand Manual

Contents
Control system .................................. 147
Multifunction display .................... 147
Multifunction steering wheel ........ 148
Menus .......................................... 150
Standard display menu ................ 154
AMG menu ................................... 156
Off-road mode menu .................... 159
Audio menu .................................. 159
Navi* menu .................................. 161
AIRMATIC*/Compass menu ........ 162
DISTRONIC* menu ....................... 162
Vehicle status message
memory menu .............................. 163
Settings menu .............................. 164
Vehicle configuration ................... 178
Trip computer menu..................... 180
Tel menu* .................................... 182
Automatic transmission ..................... 185
Gear selector lever ....................... 185
Shifting procedure ....................... 188
Transmission positions................. 189
Driving tips ................................... 191
Gear ranges ................................. 193
Steering wheel gearshift control .. 194
Shift program (ML 63 AMG only).. 195Emergency operation
(Limp-Home Mode) ....................... 198
Transfer case ...................................... 199
Good visibility ..................................... 200
Headlamp cleaning system* ......... 200
Rear view mirrors .......................... 200
Power folding exterior
rear view mirrors* ......................... 202
Sun visors ..................................... 203
Rear window defroster .................. 205
Climate control ................................... 206
Deactivating the
climate control system ................. 210
Operating the climate control
system in automatic mode............ 210
Setting the temperature................ 211
Adjusting air distribution............... 212
Adjusting air volume ..................... 212
Front defroster.............................. 213
Air recirculation mode .................. 214
Air conditioning............................. 216
Residual heat and ventilation ........ 216
Rear climate control*.................... 2173-zone automatic climate control* ..... 220
Deactivating the
automatic climate
control system .............................. 224
Operating the automatic
climate control system in
automatic mode............................ 225
Setting the temperature ............... 225
Adjusting air distribution .............. 226
Adjusting air volume ..................... 227
Front defroster ............................. 227
Maximum cooling MAX COOL ....... 228
Air recirculation mode .................. 228
Air conditioning ............................ 230
Using driver-side settings
for all temperature zones.............. 231
Residual heat and ventilation........ 232
Rear automatic climate control..... 232
Power windows .................................. 236
Opening and closing ..................... 236
Synchronizing the door windows .. 238
Summer opening feature .............. 239
Convenience closing feature......... 239
Power tilt/sliding sunroof* ................ 241
Opening and closing ..................... 241
Synchronizing ............................... 244

25 At a glance
Cockpit
Item
Page
1
Cruise control lever
246
2
Instrument cluster
26
3
Multifunction steering
wheel
30
4
Horn
5
Steering wheel gearshift
buttons
194
6
Gear selector lever for
automatic transmission
54
7
Front Parktronic* warning
indicators
276
8
Overhead control panel
33
Item
Page
9
Glove box release
Glove box lock
294
295
a
Glove box
294
b
Center console
31
c
Starter switch
40
d
Steering wheel adjustment,
manual
47
e
Hood lock release
356
f
Parking brake release
57
g
Parking brake pedal
65
h
Power tailgate switch*
119
j
Door control panel
36
Item
Page
k
Headlamp washer switch*
200
l
Exterior lamp switch
59,
136
m
Steering wheel adjustment,
electrical*
Heated steering wheel*
48
304
n
Combination switch

High beam


Turn signals


Windshield wipers


Rear window wiper
140
59
60
60
62

54 Getting startedDriving
Starting the engine Automatic transmission
Gearshift pattern for automatic
transmissionPPark position
RReverse gear
NNeutral
DDrive position
For more information on how to operate
the gear selector lever, see “Automatic
transmission” (
page 185).
Warning!
G
Do not pass belts over sharp edges. They
could tear.
Do not allow the belt to get caught in the
door or in the seat adjustment mechanism.
This could damage the belt.
Never attempt to make modifications to
seat belts. This could impair the effective-
ness of the belts.
Do not bleach or dye seat belts as this may
severely weaken them. In a crash, they may
not be able to provide adequate protection.
Damaged seat belts or belts that were highly
stressed in an accident must be replaced.
Contact an authorized Mercedes-Benz Light
Truck Center.
Warning!
G
Inhalation of exhaust gas is hazardous to
your health. All exhaust gas contains carbon
monoxide (CO), and inhaling it can cause un-
consciousness and possible death.
Do not run the engine in confined areas
(such as a garage) which are not properly
ventilated. If you think that exhaust gas
fumes are entering the vehicle while driving,
have the cause determined and corrected
immediately. If you must drive under these
conditions, drive only with at least one win-
dow fully open.

58 Getting startedDrivingDriving off
Depress the brake pedal.
The gear selector lever can now be
used.

Shift automatic transmission toD orR
(page 187).

Release the brake pedal.

Carefully depress the accelerator
pedal.After a cold start, the automatic transmis-
sion shifts at a higher engine revolution.
This allows the catalytic converter (gaso-
line engine) or the oxidation catalyst (die-
sel engine) to reach its operating
temperature earlier.
i
Wait for the gear selection process to com-
plete before setting the vehicle in motion.
i
Shifting from gear positionP to positionR,
N, orD is only possible with the brake pedal
depressed. Without the brake pedal depressed,
the gear selector lever can be moved, but the
parking pawl remains engaged, not allowing
shifting to occur.
!
If you hear a warning signal and the
message
Release parking brake
appears in
the multifunction display when driving off, you
have forgotten to release the parking brake.
Release the parking brake (
page 57).
i
Once the vehicle is in motion, the automatic
central locking system engages and the locking
knobs drop down.
The automatic door lock feature can be
deactivated (
page 176).
You can open a locked door from the inside.
Open door only when conditions are safe to do
so.
Warning!
G
On slippery road surfaces, never downshift
in order to obtain braking action. This could
result in drive wheel slip and reduced vehi-
cle control. Your vehicle’s ABS will not pre-
vent this type of loss of control.Warning!
G
It is dangerous to shift the automatic trans-
mission out ofP orN if the engine speed is
higher than idle speed. If your foot is not
firmly on the brake pedal, the vehicle could
accelerate quickly forward or in reverse. You
could lose control of the vehicle and hit
someone or something. Only shift into gear
when the engine is idling normally and when
your right foot is firmly on the brake pedal.

141 Controls in detail
Lighting
Driving forward
Switching on corner-illuminating front
fog lamps
Switch on the left or right turn signal
(page 60), depending on whether
you are turning left or right.
The respective front fog lamp comes on
and illuminates the area in the direc-
tion into which you are turning.
or

Turn steering wheel in desired direc-
tion.
The front fog lamp on the side of your
steering direction comes on.Switching off corner-illuminating front
fog lamps
The combination switch for the turn signal
resets automatically after major steering
wheel movements. This will switch off the
corner-illuminating front fog lamps if they
were activated by switching on the left or
right turn signal.
If the turn signal should stay on after
making the turn, the turn signal and the
corner-illuminating front fog lamps can be
switched off by returning the combination
switch to its original position.Driving rearward
Switching on corner-illuminating front
fog lamps

Shift the automatic transmission to
reverse gearR (
page 187).
The corner-illuminating front fog lamp
opposite to your steering direction
comes on.
Switching off corner-illuminating front
fog lamps

Shift the automatic transmission to a
gear other than reverse gearR
(page 187).
The respective corner-illuminating
front fog lamp goes out.
i
The corner-illuminating front fog lamps
temporarily come on on both sides of the vehicle
if you turn the steering wheel in one direction
and then again in the other direction shortly
thereafter.
i
The corner-illuminating front fog lamps will
come on automatically depending on the steer-
ing angle and vehicle speed, even if you did not
switch on either turn signal. If the
corner-illuminating front fog lamps came on
automatically, they will also go out automatically
depending on the steering angle and vehicle
speed.
i
There may be a brief delay before the
corner-illuminating front fog lamps switch off.

156 Controls in detailControl systemAMG menu
The main screen of the AMG menu shows
you the gear currently engaged as well as
the engine oil temperature.
Press buttonè orÿ repeatedly
until you see the AMG menu.
1Gear indicator
2Engine oil temperatureUse buttonsk orj to select the
following functions in the AMG menu:Vehicle supply voltage

Press buttonè orÿ repeatedly
until you see the AMG menu.

Press buttonj repeatedly until you
see the vehicle supply voltage.
1Gear indicator
2Vehicle supply voltage
i
This function is only available in AMG
vehicles.
i
The engine oil temperature symbol flashes if
the engine oil temperature has not yet reached
80°C. During this time, avoid driving at full
engine speed.
Function
Page
Vehicle supply voltage
156
RACETIMER
157
Overall analysis
158
Lap analysis
159
i
If the engine reaches the overspeed range in
the manual shift program, the menu will be
shown in red. In addition, you will see UP next to
gear indicator2 as a reminder to upshift.

185 Controls in detail
Automatic transmission
Automatic transmission
For more information on driving with an
automatic transmission, see “Automatic
transmission” (
page 54).
Your vehicle’s transmission adapts its gear
shifting process to your individual driving
style by continually adjusting the shift
points up or down. These shift point adjust-
ments are performed based on current
operating and driving conditions.
If the operating conditions change, the
automatic transmission reacts by
adjusting its shift program.
Gear selector lever
The gear selector lever is located on the
right of the steering column.Gearshift pattern for automatic
transmissionPPark position
RReverse gear
NNeutral
DDrive position
i
During the brief warm-up, transmission
upshifting is delayed. This allows the catalytic
converter (gasoline engine) or the oxidation
catalyst (diesel engine) to heat up more quickly
to operating temperature.
Warning!
G
Make sure that absolutely no objects are
obstructing the pedal’s range of movement.
Keep the driver’s footwell clear of all obsta-
cles. If there are any floormats or carpets in
the footwell, make sure that the pedals still
have sufficient clearance.
During sudden driving or braking maneuvers
the objects could get caught between the
pedals. You could then no longer brake or
accelerate. This could lead to accidents and
injury.

186 Controls in detailAutomatic transmission
Shifting from P to N
Moving the gear selector lever up or down
shifts the automatic transmission out of
park positionP:
With the vehicle at a standstill, depress
the brake pedal and keep it pressed.

Move gear selector lever up or down to
resistance point to select neutral
positionN.Shifting from N to R or from N to D

With the vehicle at a standstill, depress
the brake pedal and keep it pressed.

Move gear selector lever up past the
resistance point to select reverse
gearR.
or

Move gear selector lever down past the
resistance point to select drive
positionD.

Release the parking brake (
page 57).

Release the brake pedal.

Carefully depress the accelerator pedal
to drive off when it is safe to do so.
i
The current transmission positionP, R, N,
orD appears in the multifunction display
(
page 189).Warning!
G
It is dangerous to shift the automatic trans-
mission out of park positionP or neutral
positionN if the engine speed is higher than
idle speed. If your foot is not firmly on the
brake pedal, the vehicle could accelerate
quickly forward or reverse. You could lose
control of the vehicle and hit someone or
something. Only shift into gear when the
engine is idling normally and when your right
foot is firmly on the brake pedal.
i
The gear selector lever returns to its original
position.
i
The gear selector lever returns to its original
position.

187 Controls in detail
Automatic transmission
Shifting from P to R
With the vehicle at a standstill, depress
the brake pedal and keep it pressed.

Move gear selector lever up past the
resistance point to select reverse
gearR.

Release the parking brake (
page 57).

Release the brake pedal.

Carefully depress the accelerator pedal
to drive off when it is safe to do so.Shifting from P to D

With the vehicle at a standstill, depress
the brake pedal and keep it pressed.

M o v e g e a r s e l e c t o r l e v e r d o w n p a s t t h e
resistance point to select drive
positionD.

Release the parking brake (
page 57).

Release the brake pedal.

Carefully depress the accelerator pedal
to drive off when it is safe to do so.Shifting from D, R, or N to P
If you want to select park positionP with
the transmission being in drive positionD,
reverse gearR or neutral positionN:

With the vehicle at a standstill, depress
the brake pedal and keep it pressed.

Step firmly on parking brake pedal
(page 65).

Press button on gear selector lever in
direction of arrow (
page 185) to
select park positionP.

Release the brake pedal.
i
The gear selector lever returns to its original
position.
i
The gear selector lever returns to its original
position.
!
Shift the automatic transmission directly
from drive positionD to reverse gearR, from
reverse gearR to drive positionD or directly to
park positionP only when the vehicle is stopped.
Otherwise the automatic transmission could be
damaged.
When trying to free a vehicle stuck in mud or
snow, see “Rocking the vehicle” (
page 192).

188 Controls in detailAutomatic transmissionShifting from D or R to N
If you want to select neutral positionN
with the transmission being in drive
positionD or reverse gearR:
With the vehicle at a standstill, depress
the brake pedal and keep it pressed.

Step firmly on parking brake pedal
(page 65).

Move gear selector lever up to resis-
tance point when in drive positionD or
down to resistance point when in
reverse gearR to select neutral
positionN.

Release the brake pedal.
Shifting procedure
The automatic transmission selects indi-
vidual gears automatically, depending on:

drive positionD (
page 189) with gear
ranges (
page 193)


the selected program mode (M/C/S)
(ML 63 AMG only) (
page 195)


the position of the accelerator pedal
(page 191)


the vehicle speedWith drive positionD selected, you can use
the steering wheel gearshift control
buttons (
page 194) to influence trans-
mission shifting by:


limiting the gear range


changing gears manually
i
When the vehicle needs to be moved with
the engine switched off and the transmission set
to neutral positionN (
page 186), e.g. in an
automatic car wash, do not depress the parking
brake pedal.
!
Allow engine to warm up under low load use.
Do not place full load on the engine until the
operating temperature has been reached.
Shift into reverse gearR or park positionP only
when the vehicle is stopped.
Avoid spinning of a drive wheel for an extended
period when driving off on slippery road
surfaces. This may cause serious damage to the
drivetrain which is not covered by the
Mercedes-Benz Limited Warranty.