garage door opener MERCEDES-BENZ R350 2006 W251 Owner's Manual

ContentsLoading .............................................. 279
Roof rack* .................................... 279
Loading instructions ..................... 280
Cargo tie-down rings .................... 281
Hooks ........................................... 282
Expanding cargo compartment .... 283
Cargo compartment cover blind* . 288
Partition net* ............................... 290
Useful features .................................. 294
Storage compartments................. 294
Parcel nets ................................... 298
Cup holders .................................. 299
Ashtrays* ..................................... 302
Cigarette lighter* ......................... 305
Power outlets ............................... 306
Rear center console* ................... 308
Telephone*................................... 310
Tele Aid* ...................................... 311
Garage door opener* ................... 320
Compass ...................................... 327
Floormats* ................................... 328
Infrared reflecting windshield* ..... 328
Operation......................................... 329
The first 1000 miles (1500 km) ......... 330
Driving instructions............................ 331
Drive sensibly – save fuel ............. 331
Drinking and driving ..................... 331
Pedals .......................................... 331
Power assistance ......................... 331
Brakes .......................................... 332
Driving off .................................... 333
Parking ......................................... 334
Tires ............................................. 334
Hydroplaning ................................ 335
Tire traction.................................. 335
Tire speed rating .......................... 336
Winter driving instructions ........... 337
Standing water ............................. 338
Passenger compartment .............. 338
Driving abroad.............................. 339
Control and operation of radio
transmitters ................................. 339
Catalytic converter ....................... 340
Emission control .......................... 340
Coolant temperature .................... 341At the gas station .............................. 342
Refueling ...................................... 342
Check regularly and before a
long trip ....................................... 343
Engine compartment ......................... 345
Hood ............................................ 345
Engine oil ..................................... 346
Transmission fluid level................ 350
Coolant level ................................ 351
Windshield / rear window washer
system and headlamp cleaning
system* ....................................... 352
Tires and wheels................................ 353
Important guidelines .................... 353
Tire care and maintenance........... 354
Direction of rotation..................... 356
Loading the vehicle ...................... 356
Recommended tire inflation
pressure ....................................... 363
Checking tire inflation pressure ... 365
Tire labeling ................................. 375
Load identification ....................... 380
DOT, Tire Identification Number
(TIN) ............................................. 380
Maximum tire load ....................... 382
Maximum tire inflation pressure .. 382

31 At a glance
Overhead control panel
Overhead control panel
Item
Page
1
Left reading lamp on/off
154
2
Rear interior lighting on/off
154
3
Automatic interior lighting
154
4
Front interior lighting on/off
154
5
Right reading lamp on/off
154
6
Front right interior lamp
lens
154
7
Tilt/sliding sunroof* switch
Tilt/sliding panel* switch
255
259
8
Tele Aid* (emergency call
system) button
314
9
Vehicles without
telephone* installed:
Hands-free microphone for
TeleAid* (emergency call
system)
311
Item
Page
a
Interior rear view mirror
208
b
Reading lamp, front passen-
ger side
154
c
Vehicles with telephone*
installed:
Hands-free microphone for
TeleAid* (emergency call
system) and telephone*
311
d
Garage door opener*
320
e
Reading lamp, driver’s side
154
f
Front left interior lamp lens
154

320 Controls in detailUseful features
Garage door opener*
The integrated remote control is capable of
operating up to three separately controlled
devices. It provides a convenient way to
replace up to three hand-held remote
controls used to operate devices such as
garage door openers, gate openers, or
other devices compatible with HomeLink
®
or some other systems.
Before the integrated remote control can
be used, it must be programmed to the
garage door opener, gate operator or other
device you wish to operate. See the follow-
ing instructions for programming informa-
tion.
Interior rear view mirror with integrated
remote control1Indicator lamp
2 3 4Signal transmitter button
Needed for programming (not part of vehi-
cle equipment):
5Hand-held remote control of ga-
rage door opener, gate operator
or other device
6Hand-held remote control but-
ton
iWhen the anti-theft alarm or the
tow-away alarm stays on for more than
30 seconds, a call is initiated automat-
ically to the Response Center. See
anti-theft alarm system (
page 104)
and tow-away alarm (
page 106).

321 Controls in detail
Useful features
Programming the integrated remote
control
Step 1:
Switch on the ignition (
page 38).Step 2:

If you have previously programmed an
signal transmitter button and wish to
retain its programming, proceed to
step 3.
If you are programming the integrated
remote control for the first time, press
and hold the two outer signal transmit-
ter buttons2 and4 and release
them only when the indicator lamp1
begins to flash after approximately
20 seconds (do not hold the button for
longer than 30 seconds). This proce-
dure erases any previous settings for
all three channels and initializes the
memory.
If you later wish to program a second
and/or third hand-held transmitter to
the remaining two signal transmitter
buttons, do not repeat this step and be-
gin directly with step 3.
Warning!
G
Before programming the integrated remote
control to a garage door opener or gate
operator, make sure people and objects are
out of the way of the device to prevent po-
tential harm or damage. When programming
a garage door opener, the door moves up or
down. When programming a gate operator,
the gate opens or closes.
Do not use the integrated remote control
with any garage door opener that lacks
safety stop and reverse features as required
by U.S. federal safety standards (this
includes any garage door opener model
manufactured before April 1, 1982).
A garage door that cannot detect an object
– signaling the door to stop and reverse –
does not meet current U.S. federal safety
standards.
When programming a garage door opener, it
is advised to park outside the garage.
Do not run the engine while programming
the integrated remote control. Inhalation of
exhaust gas is hazardous to your health. All
exhaust gas contains carbon monoxide, and
inhaling it can cause unconsciousness and
possible death.


322 Controls in detailUseful featuresStep 3:
Hold the end of the hand-held remote
control5 of the device you wish to
train approximately 2 to 5 in
(5 to12 cm) away from the signal trans-
mitter button (2, 3 or4) to be pro-
grammed, while keeping the indicator
lamp1 in view.
Step 4:

Using both hands, simultaneously
press the hand-held remote control
button6 and the desired signal trans-
mitter button (2, 3 or4). Do not
release the buttons until step 5 is com-
pleted.
The indicator lamp1 will flash, first
slowly and then rapidly.Step 5:

After the indicator lamp1 changes
from a slow to a rapidly flashing light,
release the hand-held remote control
button and the signal transmitter but-
ton.
Step 6:

Press and hold the just-trained signal
transmitter button (2, 3 or4) and
observe the indicator lamp1.If the indicator lamp1 stays on
constantly, programming is complete
and your device should activate when
the respective signal transmitter
button (2, 3 or4) is pressed and re-
leased.
Step 7:

To program the remaining two signal
transmitter buttons, repeat the steps
above starting with step 3.
iThe indicator lamp1 flashes immedi-
ately the first time the signal transmit-
ter button is programmed. If this button
has already been programmed, the in-
dicator lamp will only start flashing af-
ter 20 seconds.
iIf the indicator lamp1 flashes rapidly
for about 2 seconds and then turns to a
constant light, continue with
programming steps 8 through 12 as
your garage door opener may be
equipped with the “rolling code”
feature.


323 Controls in detail
Useful features
Rolling code programming
To train a garage door opener (or other
rolling code devices) with the rolling code
feature, follow these instructions after
completing the “Programming” portion
(steps 1 through 6) of this text. (A second
person may make the following training
procedures quicker and easier.)
Step 8:
Locate “training” button on the garage
door opener motor head unit.
Exact location and color of the button
may vary by garage door opener brand.
Depending on manufacturer, the
“training” button may also be referred
to as “learn”or “smart” button. If there
is difficulty locating the transmitting
button, refer to the garage door opener
operator’s manual. Step 9:

Press the “training” button on the ga-
rage door opener motor head unit.
The “training light” is activated.
You have 30 seconds to initiate the follow-
ing two steps.
Step 10:

Return to the vehicle and firmly press,
hold for 2 seconds and release the pro-
grammed signal transmitter button
(2, 3 or4).
Step 11:

Press, hold for 2 seconds and release
same signal transmitter button a sec-
ond time to complete the training pro-
cess.Step 12:

Confirm the garage door operation by
pressing the programmed signal trans-
mitter button (2, 3 or4).
Step 13:

To program the remaining two signal
transmitter buttons, repeat the steps
above starting with step 3.iSome garage door openers (or other
rolling code equipped devices) may
require you to press, hold for 2 seconds
and release the same signal transmit-
ter button a third time to complete the
training process.

324 Controls in detailUseful featuresGate operator/Canadian programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission
which may not be long enough for the
integrated signal transmitter to pick up the
signal during programming. Similar to this
Canadian law, some U.S. gate operators
are designed to “time-out” in the same
manner.
If you live in Canada or if you are having
difficulties programming a gate operator
(regardless of where you live) by using the
programming procedures, replace step 4
with the following:
Step 4:
Press and hold the signal transmitter
button (2, 3 or4). Do not release
this button until it has been successful-
ly trained.

While still holding down the signal
transmitter button (2, 3 or4),
“cycle” your hand-held remote control
button6 as follows: Press and hold
button6 for 2 seconds, then release
it for 2 seconds, and again press and
hold it for 2 seconds. Repeat this se-
quence on the hand-held remote con-
trol until the frequency signal has been
learned. Upon successful training, the
indicator lamp1 will flash slowly and
then rapidly after several seconds.

Proceed with programming step 5 and
step 6 to complete.
iUpon completion of programming the
integrated remote control, make sure
you retain the hand-held remote con-
trol that came with the garage door
opener, gate operator or other device.
You may need it for use in other vehi-
cles, for future programming of an
integrated remote control, or simply for
continued use as a hand-held remote
control to operate the respective
device in other situations.

326 Controls in detailUseful featuresProgramming tips
If you are having difficulty programming
the integrated remote control, here are
some helpful tips:

Check the frequency of the hand-held
remote control5 (typically located on
the reverse side of the remote). The in-
tegrated remote control is compatible
with radio-frequency devices operating
between 288-399 MHz.


Put a new battery in the hand-held re-
mote control5. This will increase the
likelihood of the hand-held remote con-
trol sending a faster and more accurate
signal to the integrated remote control.


While performing step 3, hold the
hand-held remote control5 at differ-
ent lengths and angles from the signal
transmitter button (2, 3 or4) you
are programming. Attempt varying an-
gles at the distance of 2 to 5 inches
(5 to 12 cm) away or the same angle at
varying distances.


If another hand-held remote control is
available for the same device, try the
programming steps again using that
other hand-held remote control. Make
sure new batteries are in the hand-held
remote control before beginning the
procedure.


Straighten the antenna wire from the
garage door opener assembly. This
may help improve transmitting and/or
receiving signals.iCertain types of garage door openers
are incompatible with the integrated
remote control. If you should experi-
ence further difficulties with program-
ming the integrated remote control,
contact an authorized Mercedes-Benz
Light Truck Center, or call
Mercedes-Benz Customer Assistance
Center (in the USA only) at
1-800-FOR-MERCedes, or Customer
Service (in Canada) at
1-800-387-0100.
iUSA only:
This device complies with Part 15 of
the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any
interference received, including
interference that may cause
undesired operation.
Any unauthorized modification to this
device could void the user’s authority
to operate the equipment.

543 Index
Fuel consumption statistics
After start 192
Since last reset 193
Fuel filler flap
Locking 342
Opening 461
Unlocking 342
Fuel requirements 524
Fuel tank
Filler flap 342
Fuels, coolants, lubricants etc. 521
Functions (control system) 165
Resetting 176
Fuses 503
Fuse box in cargo compartment 504
Fuse box in passenger
compartment 505
Main fuse box 504
G
Garage door opener* 320
Gasoline additives 525
Gasoline see Fuel
GAWR 386, 530Gear range 530
Automatic transmission 202
Limiting 202
Shifting into optimal 207
Gear range limit
Canceling 207
Gear selector lever
Message in the display 421
Position 200
Position (automatic
transmission) 199
Global
Locking 112
Unlocking 112
Global Positioning System (GPS) 531
Glove box 294
Closing 294
Opening 294
Good visibility 208
GPS 531
Gross Axle Weight Rating see GAWR
Gross Trailer Weight see GTW
Gross Vehicle Weight Rating see GVWRGross Vehicle Weight see GVW
GTW 386
GVW 386, 531
GVWR 386, 531
H
Hard plastic trim items, cleaning 402
Hazard warning flasher 153
Switching off 154
Switching on 154
Head restraints
Front seats 44
Rear seats 139
Headlamp cleaning system* 352
Headlamps
Automatic control 148
Bi-Xenon* 529
Cleaning lenses 399
Cleaning system* 208, 352
Refilling washer fluid 352
Replacing bulbs 466
Switching off 65
Switching on 58
Washer fluid 528
Washer system 528