jacking MERCEDES-BENZ R350 2006 W251 Owner's Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2006, Model line: R350, Model: MERCEDES-BENZ R350 2006 W251Pages: 561
Page 272 of 561
271 Controls in detail
Driving systems
Basic settings
There are two setting from which to
choose:
Raised level, for driving on rough roads
Highway level, for driving on paved
roads in fair or better conditionCompared to the highway level, the vehicle
level changes by
+ 1.97 in (+ 50 mm) in raised level
+/- 0 in (+ 0 mm) in highway level
- 0.78 in (- 20 mm) in highspeed level
The vehicle lowers to highspeed level auto-
matically when
the vehicles speed exceeds
70 mph (112 km/h)
the vehicles speed is between
60 mph (96 km/h) and
70 mph (112 km/h) for longer than 20
seconds
!Keep in mind that in rough or uneven
roads, adjusting the vehicle to a lower
level may cause the vehicle underbody
to come in contact with the road and
result in damage to the vehicle under-
body. Always make sure the vehicle
has sufficient ground clearance before
adjusting it to a lower level.!Before jacking up the vehicle with
equipment that lifts one or more of the
wheels completely off the ground,
remove the SmartKey from the starter
switch.!Please also note the information in the
section on towing (
page 499).
iThe activation threshold is defined by
the set suspension tuning
(page 269).
iThe high-speed level is not available
when towing a trailer.iThe third available level is the
highspeed level that is set automatical-
ly.
iObey local speed limits. Use prudent
driving speeds appropriate to prevail-
ing conditions.
Page 457 of 561
456 Practical hintsWhere will I find ...?Vehicle jackThe vehicle jack is located underneath the
storage compartment floor.
Storage position
Remove vehicle jack from its storage
compartment (
page 454).
Push crank handle up.
Operational position
Turn crank handle clockwise until it
engages (operational position).
Before storing the vehicle jack in its stor-
age compartment:
The vehicle jack should be fully col-
lapsed.
The handle must be folded in (storage
position).
Warning!
G
The jack is designed exclusively for jacking
up the vehicle at the jack take-up brackets
built into both sides of the vehicle. To help
avoid personal injury, use the jack only to lift
the vehicle during a wheel change. Never
get beneath the vehicle while it is supported
by the jack. Keep hands and feet away from
the area under the lifted vehicle. Always
firmly set parking brake and block wheels
before raising vehicle with jack.
Do not disengage parking brake while the
vehicle is raised. Be certain that the jack is
always vertical (plumb line) when in use,
especially on hills. Always try to use the jack
on level surface. Make sure the jack arm is
fully seated in the jack take-up bracket.
Always lower the vehicle onto sufficient ca-
pacity jackstands before working under the
vehicle.
Page 480 of 561
479 Practical hints
Flat tire
Mounting the spare wheel
Preparing the vehicle
Prepare the vehicle as described
(page 478).
Take the wheel wrench and the vehicle
jack from the vehicle tool kit
(page 455).
Take the spare wheel from the wheel
well under the cargo compartment
floor (
page 458).Lifting the vehicle
Prevent the vehicle from rolling away
by blocking wheels with wheel chocks
or other sizable objects.
One wheel chock is included with the
vehicle tool kit (
page 455).
When changing wheel on a level surface:
Place the wheel chock in front of and
another sizable object behind the
wheel that is diagonally opposite to the
wheel being changed.
Always try lifting the vehicle using the jack
on a level surface. However, should cir-
cumstances require you to do so on a hill,
place the wheel chock and another sizable
object as follows:
Place the wheel chock and another
sizable object on the downhill side
blocking both wheels of the axle not
being worked on.
Warning!
G
The jack is designed exclusively for jacking
up the vehicle at the jack take-up brackets
built into both sides of the vehicle. To help
avoid personal injury, use the jack only to lift
the vehicle during a wheel change. Never
get beneath the vehicle while it is supported
by the jack. Keep hands and feet away from
the area under the lifted vehicle. Always
firmly set parking brake and block wheels
before raising vehicle with jack.
Do not disengage parking brake while the
vehicle is raised. Be certain that the jack is
always vertical (plumb line) when in use,
especially on hills. Always try to use the jack
on level surface. Make sure the jack arm is
fully seated in the jack take-up bracket.
Always lower the vehicle onto sufficient
capacity jackstands before working under
the vehicle.