engine coolant MERCEDES-BENZ S CLASS 2007 Owner's Manual

661 Technical data
Fuels, coolants, lubricants, etc.
Fuels, coolants, lubricants, etc.
Capacities
Vehicle components and their respective
lubricants must match. Therefore use only
products tested and approved by
Mercedes-Benz.
Please refer to the Factory Approved Ser-
vice Products pamphlet, or inquire at your
Mercedes-Benz Center.
Warning!
G
Comply with all valid regulations with re-
spect to handling, storing and disposing of
service fluids. Otherwise you could endan-
ger persons or the environment.
Keep service fluids out of the reach of chil-
dren.
If a service fluid is swallowed, contact a phy-
sician immediately.
Warning!
G
Gasoline is highly flammable and poisonous.
It burns violently and can cause serious
injury. Never allow sparks, flame or smoking
materials near gasoline!
Do not allow fuel to come into contact with
skin or clothing. Direct skin contact with fu-
els and the inhalation of fuel vapors are
damaging to health.
Switch off the engine before refueling.
Model
Capacity
Fuels, coolants, lubricants, etc.
Engine with oil filter
S 550
S 600
8.98 US qt. (8.5 l)
9.51 US qt. (9.0 l)
Approved engine oils
Automatic transmission
S 550
S 600
10.36 US qt. (9.8 l)
8.14 US qt. (7.7 l)
MB Automatic Transmission Fluid
Rear axle
S 550
1.27 US qt. (1.2 l)
Hypoid gear oil SAE 85 W 90
S600
2.11 US qt. (2.0 l)
Hydraulic system for ADS or ABC
All models
4.2 US qt. (4.0 l)
MB Hydraulic Fluid
Power steering
S 550
approx. 1.06 US qt. (1.0 l)
MB Power Steering Fluid
(Pentosin CHF 11S)
S 600
approx. 1.27 US qt. (1.2 l)

663 Technical data
Fuels, coolants, lubricants, etc.
Engine oils
Engine oils are specifically tested for their
suitability in our engines and durability for
our service intervals. Therefore, only use
approved engine oils and oil filters
required for vehicles with Maintenance
System (U.S. vehicles) or FSS PLUS (Cana-
da vehicles). For a listing of approved en-
gine oils and oil filters, refer to the Factory
Approved Service Products pamphlet, or
contact an authorized Mercedes-Benz
Center.
Engine oil additives
Do not blend oil additives with engine oil.
They may damage the engine. Damage or
malfunctions resulting from blending oil
additives are not covered by the
Mercedes-Benz Limited Warranty.Air conditioning refrigerant
R-134a (HFC) refrigerant and special PAG
lubricating oil are used in the air condition-
ing system.
Never use R-12 (CFC) or mineral-based lu-
bricating oil. Otherwise damage to the
system will occur.
Brake fluid
During vehicle operation, the boiling point
of the brake fluid is continuously reduced
through the absorption of moisture from
the atmosphere.
Only brake fluid approved by
Mercedes-Benz is recommended. Your au-
thorized Mercedes-Benz Center will pro-
vide you with additional information.
!
Using engine oils and oil filters of
specification other than those expressly re-
quired for the Maintenance System
(U.S. vehicles) or FSS PLUS (Canada vehicles),
or changing of oil and oil filter at change intervals
longer than those called for by the Maintenance
System (U.S. vehicles) or FSS PLUS (Canada ve-
hicles) will result in engine damage not covered
by the Mercedes-Benz Limited Warranty.
Please follow Maintenance System
(U.S. vehicles) or FSS (Canada vehicles) recom-
mendations for scheduled oil changes. Failure to
do so will result in engine damage not covered by
the Mercedes-Benz Limited Warranty.
Warning!
G
Under extremely strenuous operating condi-
tions, this moisture content can lead to the
formation of bubbles in the system, thus re-
ducing the system’s efficiency.
Therefore, the brake fluid must be replaced
regularly. Refer to your vehicle's Mainte-
nance Booklet for replacement interval.

664 Technical dataFuels, coolants, lubricants, etc.Premium unleaded gasoline
Fuel requirements
Use only premium unleaded fuel:

The octane number (posted at the
pump) must be 91 min. It is an average
of both the Research (R) octane num-
ber and the Motor (M) octane number:
(R+M)/2). This is also known as the
ANTI-KNOCK INDEX.
Unleaded gasoline containing oxygenates
such as ethanol, IPA, IBA and TBA can be
used provided the ratio of any one of these
oxygenates to gasoline does not exceed
10%; MTBE must not exceed 15%.
The ratio of methanol to gasoline must not
exceed 3% plus additional co-solvents.
Using mixtures of ethanol and methanol is
not allowed. Gasohol, which contains
10% ethanol and 90% unleaded gasoline,
can be used.
These blends must also meet all other fuel
requirements, such as resistance to spark
knock, boiling range, vapor pressure, etc.
Warning!
G
Gasoline is highly flammable and poisonous.
It burns violently and can cause serious
injury. Whenever you are around gasoline,
avoid inhaling fumes and skin contact, extin-
guish all smoking materials. Never allow
sparks, flame or smoking materials near
gasoline!
Switch off the engine before refueling.Warning!
G
Do not allow fuel to come into contact with
skin or clothing.
Direct skin contact with fuels and the inha-
lation of fuel vapors are damaging to health.
!
To maintain the engine’s durability and per-
formance, premium unleaded gasoline must be
used. If premium unleaded gasoline is not avail-
able and low octane fuel is used, follow these
precautions:


Have the fuel tank only partially filled with
unleaded regular and fill up with premium
unleaded as soon as possible.


Avoid full throttle driving and abrupt acceler-
ation.


Do not exceed an engine speed of 3000 rpm
if the vehicle is loaded with a light load such
as two persons and no luggage.


Do not exceed
2/3 of maximum accelerator
pedal position if the vehicle is fully loaded or
operating in mountainous terrain.

665 Technical data
Fuels, coolants, lubricants, etc.
Gasoline additives
A major concern among engine manufac-
turers is carbon build-up caused by gaso-
line. Mercedes-Benz recommends only the
use of quality gasoline containing additives
that prevent the build-up of carbon depos-
its.
After an extended period of using fuels
without such additives, carbon deposits
can build up especially on the intake valves
and in the combustion area, leading to en-
gine performance problems such as:

Warm-up hesitation


Unstable idle


Knocking/pinging


Misfire


Power lossIn areas where carbon deposits may be en-
countered due to lack of availability of gas-
olines which contains these additives,
Mercedes-Benz recommends the use of
additives approved by us for use on
Mercedes-Benz vehicles. Refer to Factory
Approved Service Products Pamphlet for a
listing of approved product(s). Follow di-
rections on product label.
Do not blend other fuel additives with fuel.
This only results in unnecessary cost and
may be harmful to the engine operation.
Damage or malfunction resulting from
poor fuel quality or from blending addition-
al fuel additives other than those tested
and approved by us for use on
Mercedes-Benz vehicles listed in the Fac-
tory Approved Service Products Pamphlet
are not covered by the Mercedes-Benz
Limited Warranty.
Coolants
The engine coolant is a mixture of water
and anticorrosion/antifreeze, which pro-
vides:

Corrosion protection


Freeze protection


Boiling protection (by increasing the
boiling point)
The cooling system was filled at the factory
with a coolant providing freeze protection
to approximately –22°F (–30°C) and cor-
rosion protection.
If the antifreeze mixture is effective to
–22°F (–30°C), the boiling point of the
coolant in the pressurized cooling system
is reached at approximately 266°F
(130°C).

666 Technical dataFuels, coolants, lubricants, etc.The coolant solution must be used
year-round to provide the necessary corro-
sion protection and increase boil-over pro-
tection. Refer to Maintenance Booklet for
replacement interval.
Coolant system design and coolant used
determine the replacement interval. The
replacement interval published in the
Maintenance Booklet is only applicable if
MB 325.0 anticorrosion/antifreeze solu-
tion or other Mercedes-Benz approved
products of equal specification (see
Factory Approved Service Products pam-
phlet) are used to renew the coolant con-
centration or bring it back up to the proper
level.
To provide important corrosion protection,
the solution must be at least 45% anticor-
rosion/antifreeze [equivalent to freeze
protection to approximately –22°F
(–30°C)]. If you use a solution that is more
than 55% anticorrosion/antifreeze [freeze
protection to approximately –49°F
(–45°C)], the engine temperature will in-
crease due to the lower heat transfer capa-bility of the solution. Therefore, do not use
more than this amount of anticorrosion/
antifreeze.
If the coolant level is low, water and
MB 325.0 Anticorrosion/Antifreeze
should be used to bring it up to the proper
level (have cooling system checked for
signs of leakage).
The water in the cooling system must meet
minimum requirements, which are usually
satisfied by normal drinking water. If you
are not sure about the water quality, con-
sult an authorized Mercedes-Benz Center.Anticorrosion/antifreeze
Your vehicle contains a number of alumi-
num parts. The use of aluminum compo-
nents in motor vehicle engines
necessitates that anticorrosion/antifreeze
coolant used in such engines be specifical-
ly formulated to protect the aluminum
parts. (Failure to use such anticorrosion/
antifreeze coolant will result in a signifi-
cantly shortened service life.)
Therefore, the following product is strongly
recommended for use in your vehicle:
Mercedes-Benz 325.0 anticorrosion/
antifreeze agent.
Before the start of the winter season (or
once a year in hot southern regions), you
should have the anticorrosion/antifreeze
concentration checked. The coolant is also
regularly checked each time you bring your
vehicle to an authorized Mercedes-Benz
Center for service.

668 Technical dataFuels, coolants, lubricants, etc.Windshield and headlamp washer system
Both the windshield and headlamp washer
systems are supplied from the windshield
washer fluid reservoir.
The washer fluid reservoir has a capacity of
approximately:

6.93 US qt (6.56 l) in vehicles
with Airmatic*


6.76 US qt (6.4 l) in vehicles with ABC*

Refill the reservoir with MB Windshield
Washer Concentrate and water (or con-
centrate and commercially available
premixed windshield washer solvent/
antifreeze, depending on ambient tem-
peratures).Windshield and headlamp washer fluid
mixing ratio
For temperatures above freezing point, use
MB Windshield Washer Concentrate
“MB SummerFit” and water:


1 part “MB SummerFit” to 100 parts
water
[1.34 fl oz (40 ml) “MB SummerFit” to
1 gal (4.0 l) water].
For temperatures below freezing point, use
MB Windshield Washer Concentrate
“MB SummerFit” and commercially avail-
able premixed windshield washer sol-
vent/antifreeze:


1 part “MB SummerFit” to 100 parts
solvent
[1.34 fl oz (40 ml) “MB SummerFit” to
1 gal (4.0 l) solvent].
Warning!
G
Washer solvent/antifreeze is highly flamma-
ble. Do not spill washer solvent/antifreeze
on hot engine parts, because it may ignite
and burn. You could be seriously burned.

676 Technical termsPCMCIA
(P
ersonal C
omputer M
emory C
ard
I
nternational A
ssociation)
Portable memory cards designed to be
inserted into laptop computers to en-
able additional functions.
PIN code
(P
ersonal I
dentification N
umber code)
Your PIN code prevents unauthorized
persons from using your ->GSM mobile
phone. The PIN code is a number
string, which you have to enter when
switching on the telephone.
Poly-V-belt drive
Drives engine components (alternator,
AC compressor, etc.) from the engine.Power train
Collective term designating all compo-
nents used to generate and transmit
motive power to the drive axles, includ-
ing:


Engine


Clutch/torque converter


Transmission


Transfer case


Drive shaft


Differential


Axle shafts/axles
PRE-SAFE
®
(Pre
ventive Occupant Safe
ty System)
Vehicles equipped with PRE-SAFE
®
take preventive measures when the
system senses certain driving dynam-
ics suggesting a possible accident.
Production options weight
(
page 527)Program mode selector switch
Used to switch the automatic transmis-
sion between standard operationS and
comfort operationC.
PSI
(P
ounds per s
quare i
nch)
(
page 527)
PUK
(Personal U
nblocking K
ey)
Must be entered if the wrong ->PIN was
entered three consecutive times.
Recommended tire inflation pressure
(
page 527)
REST
(Residual engine heat utilization)
Feature that uses the engine heat
stored in the coolant to heat the vehi-
cle interior for a short time after the en-
gine has been turned off.

685 Index
Dynamic Rear View Monitor* 413
Parallel parking 417
Reverse parking (back-in
parking) 415
Switching on 415
View through the camera 413
E
Easy-entry/exit feature 328
COMAND menu 224
EBP 71
ELCODE 672
Electric parking brake 364
Electrical fuses see Fuses
Electrical outlet see Power outlet
Electrical system, Technical Data 659
Electronic Brake Proportioning see EBP
Electronic Stability Program see ESP
®
Emergency call system 462
Emergency calls, Tele Aid 463
Emergency engine shut-down 648
Emergency operation (Limp-Home
Mode) 377
Emergency operations
Locking the vehicle 614
mechanically releasing the parking
brake 616Releasing from inside 440
Remote door lock 469
Remote door unlock 468
Tilt/sliding sunroof or tilt/sliding
panel* 617
Unlocking the trunk 615
Unlocking the vehicle 614
Emergency tensioning device see ETD
Emergency, In case of
Battery, Jump starting 639
First aid kit 611
Flat tire 629
Fuses 645
Instrument cluster, Indicator
lamps 544
Roadside Assistance 16
Roadside Assistance (Tele Aid) 465
Towing the vehicle 642
Emission control 488
Emission control information label 652
Emission control system warranties 14
Engine
Belt layout 653
Cleaning 536
Compartment 492
Coolant 497, 662, 665Malfunction indicator lamp 547
Number 652, 672
Oil 496, 661, 663
Oils 494
Residual heat and ventilation 433
Starting 359
Technical data 654
Turning off 365
Engine coolant see Coolant
Engine oil 494
Adding 496
Additives 663
Checking level 494
Checking level (Dipstick) 495
Checking level (Instrument cluster con-
trol system) 494
Consumption 494
Dipstick 495
Filler neck 496, 497
Messages in display 495, 602
Recommended engine oils and oil
filters 661
Viscosity 672
ESP
®
72
Messages in display 572, 582
Warning lamp 549

686 IndexETD 58, 672
Safety guidelines 47
Exterior lighting
Delayed switch-off (COMAND) 220
Locator lighting (COMAND) 221
Exterior rear view mirrors
Adjusting 332
Auto-dimming on the driver’s
side 334
Fold in automatically when locking
(COMAND) 222
Lower mirror when reversing
(COMAND) 222
Power folding 333
F
Favorite button 216
First aid kit 611
Flat tire 629
Jacking up the vehicle 630
Lowering the vehicle 633
Mounting the Minispare wheel 629
Preparing the vehicle 629
Flexible Service System see FSS
Fluids
Automatic transmission fluid 661
Brake fluid 662, 663Capacities 661
Engine coolant 497, 662, 665
Engine oil 496, 661, 663
Power steering fluid 661
Windshield washer and headlamp
cleaning system 662, 668
Fog lamps
Messages in display 598
Replacing bulbs 622
Front air bags 49
Front lamps
Replacing bulbs 622, 623
Front lamps see headlamps
Front passenger front air bag 49
Front passenger front air bag off indicator
lamp 53, 555
FSS (Canada vehicles) 532
Fuel 490, 662, 664
Additives 665
Capacity, Fuel tank 662
Filling the tank 489
Fuel filler flap and cap 489
Fuel reserve warning lamp 29, 550
Premium unleaded gasoline 490,
662, 664
Requirements, Octane rating 664Fuel cap
Message in display 591
Fuel consumption statistics
After start 245
Since last reset 245
Fuel filler flap 489
Locking/Unlocking 489
Fuel tank
Capacity 662
Filler flap 489
Fuels, coolants, lubricants etc.
Capacities 661
Fuses 645
Aids for replacing fuses 646
Fuse box in engine compartment 646
Fuse box in passenger
compartment 647
Fuse boxes in dashboard 647
Fuse chart (vehicle tool kit) 611
Fuse extractor (vehicle tool kit) 611
Replacing 645
Spare fuses (vehicle tool kit) 611

688 IndexInfant and child restraint systems see Chil-
dren in the vehicle
Inflation pressure see Tires
Infrared reflecting windshield 475
Inside door handle 312
Instrument cluster 28, 378, 674
Cleaning 541
Coolant temperature gauge 378
Illumination 81, 378
Lamps 544
Multifunction display 241
Outside temperature indicator 379
Selecting the language
(COMAND) 216
Interior lighting 348
Activating automatic control 349
Ambient lighting (COMAND) 225
Deactivating automatic control 349
Delayed switch-off (COMAND) 226
In the rear 350
Reading lamps in the front 349
Reading lamps in the rear 350
Interior rear view mirror
Adjusting 332
Auto-dimming 334Interior storage spaces see Storage com-
partments
J
Jack 612, 630
Jacking up the vehicle 630
Jump starting 639
K
Key, Mechanical 614
Loss of 311
Key, SmartKey 304
Battery check lamp 304, 305
Factory setting 305
Global locking and unlocking 305
Lock button 304
Locking and unlocking 304
Loss of 311
Messages in display 593
Opening button for trunk 304
Panic button 68
Remote control 304
Restoring to factory setting 306
Selective setting 305
Starting the engine 359
Switching on ignition with 315Turning off engine 366
Unlock button 304
Key, SmartKey with KEYLESS-GO* 306
Battery check lamp 306, 310
Closing, Trunk 440
Factory setting 309
Global locking and unlocking 309
Important notes on using
KEYLESS-GO* 308
Lock button 306
Locking and unlocking 306
Locking using the lock button on door
or on trunk lid 310
Loss of 311
Messages in display 592
Opening button for trunk 306
Panic button 68
Remote control 306
Restoring to factory setting 310
Selective setting 310
Starting the engine 360
Switching on ignition with 317
Turning off engine 366
Unlock button 306
Kickdown 373, 674
Kilopascal 527