display MERCEDES-BENZ S-Class 2008 W221 Comand Manual

485 Controls in detail
Driving systems

Press# on the multifunction steer-
ing wheel to confirm.
The display in the instrument cluster
changes to the Advanced Parking Guid-
ance.
1Green lane
2White bracket indicates the stopping
position

Where necessary, depending on the
distance to the parking space, back up
in a straight line a short distance.
This is indicated by a green lane1.

Back up until you hear an audible warn-
ing, then stop.
The stopping position has been
reached, indicated by a white
bracket2.
3Red lane indicates the current steering
wheel position
4Yellow lane indicates the required
steering wheel position

When the vehicle is stationary, turn the
steering wheel until the red lane3
matches up with the yellow lane4.The lane4 then turns green. If the
parking space is located within the dis-
play range, a white bracket with an ar-
row for the target position is shown at
the end of the green lane.
Driving into the parking space
1Green lane indicates the correct steer-
ing wheel position

Maintain the steering wheel position
and carefully back up.

Stop as soon as you hear the audible
warning.
The vehicle has reached the position
for countersteering.

486 Controls in detailDriving systemsCountersteering
1Red lane indicates the current steering
wheel position
2Yellow lane indicates the required
steering wheel position
When the vehicle is stationary, turn the
steering wheel until the red lane1
matches up with the yellow lane2.
The lane2 then turns green and a
white arrow and a white bracket are
shown to indicate the target position.Reaching end position
1Green lane indicates the correct steer-
ing wheel position

Maintain the steering wheel position
and carefully back up until the end po-
sition has been reached.
The message appears “Parking Guid-
ance Finished” in the multifunction dis-
play and you will hear an audible
warning.
If the distance to the rear is too short,
you will also be audibly warned by the
Park Assist* system (
page 476).
End positionDepending on the size of the parking
space, the vehicle may be positioned at an
angle in the parking space. Advanced Park-
ing Guidance guides you close to the rear
limit of the parking space where possible.
Adjust the end position by maneuver-
ing as needed.

Observe the Park Assist* display
(page 476).

487 Controls in detail
Driving systems
Canceling the Advanced Parking
Guidance
Press the Park Assist* button
(page 480).
The Advanced Parking Guidance is im-
mediately canceled and Park Assist* is
deactivated. No message is shown in
the multifunction display.
The Advanced Parking Guidance is auto-
matically canceled if guidance into the
parking space is no longer possible or if an
error occurs.
The parking space symbol disappears and
the message “Parking Guidance Canceled”
appears in the multifunction display.
Rear View Camera*
T he R e a r V i e w C a m e r a i s a n e l e c t r o n i c a n d
visual parking aid. It shows you the area
behind the vehicle on the COMAND dis-
play.
In addition, the Rear View Camera contains
guide lines to help you with driving in re-
verse.
The area behind the vehicle is displayed as
a reverse-mirror image similar to the view
in a rear-view mirror.The Rear View Camera is in the handle
strip of the trunk lid.
1Rear View Camera

488 Controls in detailDriving systemsView through the camerai
The image from the Rear View Camera is
shown mirror-inverted on the COMAND display
(
page 31).Warning!
G
Please note that objects which do not touch
the ground, such as the bumper of a vehicle
parked behind you, a trailer hitch, or the
back of a truck, may appear to be further
away than they actually are. In this case, you
should not use the guide lines to judge dis-
tance. The use of the guide lines to judge
distance increases the risk of impacting the
objects.
Warning!
G
The Rear View Camera is a supplement sys-
tem. It is not intended to, nor does it re-
place, the need for extreme care. The
responsibility during parking and other driv-
ing maneuvers always remains with the driv-
er.
The Rear View Camera may show obstacles
with a distorted perspective, incorrectly or
not at all.
Special attention must be paid to objects
outside of the camera’s field of view such as
those located very close to or below the rear
bumper, or above the recessed grip of the
luggage compartment lid. Such objects may
not be detected by the system and can dam-
age the vehicle.
The Rear View Camera does not warn you
about impending collisions with objects. The
driver is always responsible for safety and
must continue to pay attention to the imme-
diate surroundings while parking or maneu-
vering the vehicle. This applies not only to
the area behind the vehicle, but also to the
area in front of and to the sides of the vehi-
cle. Failure to do so could result in injury to
persons and/or damage to the vehicle or
other property. We also recommend that the
driver uses the Parktronic system* or Park
Assist* when parking or maneuvering the
vehicle.

489 Controls in detail
Driving systems
Switching on Rear View Camera
Switch on the ignition (
page 370).

Switch on COMAND (
page 87).

Move gear selector lever to reverse
gearR.
The COMAND display will show the
area behind the vehicle with guide
lines.
Warning!
G
Make sure no persons or animals are in the
area in which you are maneuvering. You
could otherwise injure them.Warning!
G
The Rear View Camera may not function if:

the trunk lid is not completely closed


it is raining or snowing heavily, or if
there is thick fog


in a very dark area


the camera is exposed to very strong
white light (white stripes may appear on
the COMAND display)


the surrounding area is lit with fluores-
cent light (the COMAND display can
flicker)


outside temperatures are very high (lens
condensation)


there is a sudden change in tempera-
ture, for example when you drive out of
the cold into a heated garage in winter
(lens condensation)


the camera lens is dirty or covered, see
“Cleaning the Rear View Camera* lens”
(page 621)


the rear of your vehicle is damaged. In
this case, have the position and setting
of the camera checked by a qualified
technician. Contact an authorized
Mercedes-Benz Center.
Do not use the Rear View Camera if the
roads are icy, slippery or covered with snow.
The vehicle could slip causing the actual ve-
hicle position to deviate from the one shown
on the COMAND display.
This may cause injury to you or others, or
damage the vehicle or objects.
Mounting tires/rims of other specification
than the original equipment tires/rims may
impair the function of the Rear View Cam-
era. Contact an authorized Mercedes-Benz
Center.
Warning!
G
Use of Rear View Camera can be dangerous
if you are color-blind or have impaired color
vision.
Only use Rear View Camera if you can see
and distinguish all colored guide lines shown
by Rear View Camera on the COMAND dis-
play.i
The Rear View Camera must be activated in
the instrument cluster control system in order
for it to be switched on (
page 303).


491 Controls in detail
Driving systems
Night View Assist*
Night View Assist illuminates the road with
infrared light in addition to the normal
headlamps.
A camera at the top of the windshield mea-
sures the infrared light and shows a
black-and-white image on the multifunc-
tion display. The image on the multifunction display cor-
responds to a road lit up by high-beam
headlamps.
The Night View Assist image on the multi-
function display is not impaired


by the headlamps of approaching vehi-
cles


if you cannot switch on the high beams
due to oncoming traffic
As a result, you can better follow the
course of the road and detect obstacles
earlier on.The camera is at the top of the windshield.
1Night View Assist camera
Switching on or off
You can only switch on the Night View As-
sist if


the SmartKey in the starter switch is
set to position2


it is dark
Warning!
G
Night View Assist is only an aid to support
you while driving and cannot substitute your
careful attention. Do not rely on the display
of the Night View Assist; instead, continue
to look through the windshield. You are al-
ways responsible for safety and must drive
in accordance with traffic conditions. Other-
wise, you could endanger yourself and oth-
ers.
If it is foggy, raining or snowing, the clarity of
the Night View Assist image on the multi-
function display may be diminished.
Warning!
G
Night View Assist cannot record objects im-
mediately in front of or next to the vehicle.
When maneuvering, continue to look
through the windshield. Make sure no per-
sons or animals are in the area in which you
are maneuvering. You could otherwise in-
jure them.
i
Infrared light is invisible to the human eye
and can therefore remain permanently switched
on without blinding oncoming traffic.

492 Controls in detailDriving systems

the light switch is set to * or B
or if the daytime driving lamps are
switched on


the automatic transmission is not in re-
verse gearR
1Night View Assist on or off

Press button1 up or down.
The Night View Assist image appears
on the multifunction display.Image on multifunction display
When you switch on Night View Assist, the
image for the speed gauge changes on the
multifunction display. The speed gauge is
shown as a bar on the lower edge of the
multifunction display. The line for main
menus is no longer available. If you would
like to change a setting using the steering
wheel buttons, you must first switch off
Night View Assist.
1Night View Assist image
2Speedometer displayAdjusting instrument cluster
illumination
1Knob

Make sure the Night View Assist is
switched on.

Brightening illumination: Turn
knob1 clockwise.

Dimming illumination: Turn knob1
counterclockwise.
i
The infrared headlamps only come on above
a speed of approximately 9 mph (15 km/h).
Therefore, when you are at a standstill, you do
not have a complete view and cannot check the
function of the Night View Assist.
i
If you change the brightness of the instru-
ment cluster while Night View Assist is switched
on, only the brightness of the multifunction dis-
play is changed.

496 Controls in detailDriving systemsSensor monitoring range
Blind Spot Assist is able to monitor a range
up to three meters to the rear and both
sides of the vehicle.
The Blind Spot Assist sensors are built into
t h e f r o n t a n d r e a r b u m p e r s . M a k e s u r e t h a t
the area of the bumpers around the sen-
sors is free of dirt, ice and snow. The radar
sensors must not be obstructed, for exam-
ple, by bicycle carriers or overhanging lug-
gage.
Warning!
G
Blind Spot Assist monitors certain areas in
the immediate vicinity of your vehicle. Vehi-
cles approaching and passing at increased
speeds will not be detected. There will be no
warning display and no audible warning.
When driving in a very wide lane, the sensors
may not be able to cover the entire width of
the neighboring lane. Vehicles driving on the
outside of the neighboring lane may not be
detected.
It is the driver’s responsibility at all times to
be attentive to road, weather and traffic con-
ditions and to provide the steering, braking
and other driving inputs necessary to retain
control of the vehicle. Failure to do so could
result in recognizing dangers too late, possi-
bly resulting in an accident and serious inju-
ry to yourself and others.
When driving in a very narrow lane, the sen-
sors may detect and display vehicles in the
second lane over. This will be the case if
there are vehicles driving on the inside edge
of their lane.!
In the event of a significant impact or dam-
age affecting the bumpers, have the radar sen-
sors checked by a qualified specialist workshop
such as a Mercedes-Benz Center. Failure to do
this can result in Blind Spot Assist not function-
ing correctly.

503 Controls in detail
Automatic climate control
The following automatic climate control
functions can be operated via COMAND:
Deactivating climate control system
Deactivating: Press button´
(page 501) up or down.
The indicator lamp on the button
comes on. You will see “Climate Con-
trol OFF” in the COMAND display.

Reactivating: Press button´
(page 501) up or down.
The indicator lamp on the button goes
out. You will see the previous settings
in the COMAND display.Operating climate control system in
automatic mode
Air distribution and air volume is adjusted
automatically by the automatic climate
control system. You can also adjust the
settings for air distribution and air volume
manually.
Activating
Press buttonU (
page 501) up or
down.
The indicator lamp on the button
comes on.
Do not obstruct air volume by placing objects on
the air volume-through exhaust slots below the
rear window.Function
Page
Temperature
274
Air distribution
275
Air volume
275
Switching off cooling (“AC
OFF”)
276
Central climate control (“Mono”)
277
Footwell temperature
278
Air flow from air vents
279
Rear climate control*
279
Warning!
G
When the automatic climate control is
switched off, the outside air supply and cir-
culation are also switched off. Only choose
this setting for a short time. Otherwise the
windows could fog up, impairing visibility
and endangering you and others.
i
In automatic mode, cooling with dehumidify
is switched on. This function can be switched off
if necessary (
page 276).

506 Controls in detailAutomatic climate controlRear window defroster
Activating
Switch on the ignition (
page 370).

Press button< (
page 501) up or
down.
The indicator lamp on the button
comes on.
Deactivating

Press button< (
page 501) up or
down.
The indicator lamp on the button goes
out.
Maximum cooling MAXCOOL (USA only)
If U is selected on both the left and
right side and there is a high demand for
cooling, the display “MAXCOOL” appears
in the COMAND display.
This provides the fastest possible cooling
of the vehicle interior (when windows and
tilt/sliding sunroof or tilt/sliding panel*
are closed).
Air recirculation mode
Switch to air recirculation mode to prevent
unpleasant odors from entering the vehicle
from the outside (e.g. before driving in a
tunnel). This setting cuts off the intake of
outside air and recirculates the air in the
passenger compartment.
!
The rear window defroster uses a large
amount of power. To keep battery drain to a min-
imum, switch off the defroster as soon as the
rear window is clear.
i
The defroster is automatically deactivated
after some time of operation depending on the
outside temperature.
Warning!
G
Any accumulation of snow and ice should be
removed from the rear window before driv-
ing. Visibility could otherwise be impaired,
endangering you and others.i
If the rear window defroster switches off too
soon and the indicator lamp goes out, this indi-
cates that too many electrical consumers are op-
erating simultaneously and the load on the
battery is reducing available voltage. The system
responds automatically by deactivating the rear
window defroster.
i
Maximum cooling MAXCOOL is only avail-
able when the engine is running.Warning!
G
Fogged windows impair visibility, endanger-
ing you and others. If the windows begin to
fog on the inside, switching off the air
recirculation mode immediately should clear
interior window fogging. If interior window
fogging persists, make sure the air
conditioning (
page 276) is activated, or
press button;.