ignition MERCEDES-BENZ S-Class 2008 W221 Comand Manual

420 Controls in detailDriving and parkingFor more information, see “Driving instruc-
tions” (
page 559).
Turn signalsCombination switch1Turn signals, right
2Turn signals, left
Press the combination switch in the
direction of arrow1 or2.
The corresponding turn signal indicator
lampL orK in the instrument
cluster flashes (
page 28).
The combination switch resets automati-
cally after major steering wheel move-
ments.
Problems while driving
The engine runs erratically and misfires

An ignition cable may be damaged.


The engine electronics may not be op-
erating properly.


Unburned gasoline may have entered
the catalytic converter and damaged it.

Give very little gas.

Have the problem repaired by an au-
thorized Mercedes-Benz Center as
soon as possible.
!
Shift the automatic transmission to park
positionP or reverse gearR only when the vehi-
cle is stopped in order to avoid damaging the
transmission.
!
Do not run cold engine at high engine
speeds. Running a cold engine at high engine
speeds may shorten the service life of the en-
gine. This is not covered by the Mercedes-Benz
Limited Warranty.
S63AMG and S65AMG only:
At engine temperatures below 68°F (20° C), the
maximum speed is restricted in order to protect
the engine. Avoid driving the vehicle at full speed
while the engine is cold in order to prevent pre-
mature engine wear as well as diminished com-
fort.
!
Simultaneously depressing the accelerator
pedal and applying the brakes reduces engine
performance and causes premature brake and
drivetrain wear which is not covered by the
Mercedes-Benz Limited Warranty.
i
To signal minor directional changes such as
changing lanes, press combination switch only
to point of resistance and release. The corre-
sponding turn signals will flash three times.

423 Controls in detail
Driving and parking
1Handle for electronic parking brake
Manually releasing electronic parking
brake
Pull handle1.
The red indicator lamp 0 (USA only)
or ! (Canada only) in the instru-
ment cluster goes out.
You cannot release the electronic parking
brake until the ignition is switched on.Automatically releasing electronic park-
ing brake
Your vehicle’s electronic parking brake is
automatically released when:


The engine is running.


Transmission is in drive positionD or
reverse gearR.


The hood is closed.


You have fastened your seat belt.


You step on the accelerator pedal.
If reverse gearR is engaged, the trunk
must be closed. Manually engaging electronic parking
brake

Press handle1.
The red indicator lamp 0 (USA only)
or ! (Canada only) in the instru-
ment cluster comes on.
i
If you have not fastened your seat belt, the
following conditions must be met in order for the
electronic parking brake to be automatically re-
leased:


The driver’s door is closed.


You must move the gear selector out of park
positionP position or drive faster than 2 mph
(3 km/h).
i
You can also engage the electronic parking
brake when the SmartKey is removed from the
starter switch.

432 Controls in detailAutomatic transmissionIf you want the gear position to remain in
neutral positionN, e.g. when taking the
vehicle through an automatic conveyor
type car wash or when towing the vehicle,
observe the following instructions.Vehicles with SmartKey:

With the vehicle at a standstill and the
ignition switched on shift the
automatic transmission to neutral
positionN.

If engaged, manually release the
electronic parking brake (
page 423).

Switch off the ignition and leave the
SmartKey in the starter switch.
Vehicles with KEYLESS-GO*:

With the vehicle at a standstill, depress
the brake pedal and keep it pressed.

Shift the automatic transmission to
park positionP.

Release the brake pedal.

Remove the KEYLESS-GO start/stop
button from the starter switch
(page 371).

Insert the SmartKey with KEYLESS-GO
into the starter switch.

With the ignition switched on shift the
automatic transmission to neutral
positionN.

If engaged, manually release the
electronic parking brake (
page 423).

Switch off the ignition and leave the
SmartKey with KEYLESS-GO in the
starter switch.
!
If you turn off the engine using the
SmartKey or the KEYLESS-GO* start/stop
button, the transmission will shift to neutral
positionN automatically.
Warning!
G
When leaving the SmartKey or SmartKey
with KEYLESS-GO* in the starter switch, do
not leave children unattended in the vehicle.
It is possible for children to switch on the
ignition which could result in unsupervised
use of vehicle equipment. Unsupervised use
of vehicle equipment could result in an
accident and/or serious personal injury.
!
Coasting the vehicle, or driving for any other
reason in neutral positionN can result in trans-
mission damage that is not covered by the
Mercedes-Benz Limited Warranty.
!
Observe instructions


when taking the vehicle through an
automatic conveyor type car wash
(page 618)


when towing the vehicle (
page 737)

444 Controls in detailInstrument clusterA full view illustration of the instrument
cluster can be found in the “At a glance”
section of this manual (
page 28).
The instrument cluster is activated when
you:


open a door


switch on the ignition (
page 370)


switch on the exterior lamps
The language setting for the multifunction
display can be changed via COMAND
(
page 262).Adjusting instrument cluster display
illumination
1Knob

Brightening illumination: Turn
knob1 clockwise.

Dimming illumination: Turn knob1
counterclockwise.
Coolant temperature gauge
The coolant temperature gauge is on the
left side in the instrument cluster
(page 28).
Warning!
G
No messages will be displayed if either the
instrument cluster or the multifunction dis-
play is inoperative.
As a result, you will not be able to see infor-
mation about your driving conditions, such
as speed or outside temperature, warning/
indicator lamps, malfunction/warning mes-
sages or the failure of any systems. Driving
characteristics may be impaired.
If you must continue to drive, please do so
with added caution. Contact an authorized
Mercedes-Benz Center as soon as possible.i
The instrument cluster illumination is
dimmed or brightened automatically to suit am-
bient light conditions.
The instrument cluster illumination will also be
adjusted automatically when you switch on the
vehicle’s exterior lamps.
Warning!
G


Driving when your engine is overheated
can cause some fluids which may have
leaked into the engine compartment to
catch fire. You could be seriously
burned.


Steam from an overheated engine can
cause serious burns and can occur just
by opening the hood. Stay away from
the engine if you see or hear steam com-
ing from it.
Stop the vehicle in a safe location away from
other traffic. Turn off the engine, get out

473 Controls in detail
Driving systems
The Parktronic system is an electronic
parking aid with ultrasonic sensors that
helps you while parking.
It visually and audibly indicates the relative
distance between the vehicle and an ob-
stacle.
The Parktronic system is automatically ac-
tivated when you switch on the ignition, re-
lease the electronic parking brake or start
the engine and engage drive positionD, re-
verse gearR or neutral positionN.The Parktronic system deactivates at
speeds over approximately 11 mph
(18 km/h). At lower speeds the Parktronic
system turns on again.
The Parktronic system also deactivates
when you set the automatic transmission
to park positionP or secure the vehicle in
place with the electronic parking brake
and switch off the engine.
The Parktronic system monitors the sur-
roundings of your vehicle with six sensors
in the front bumper and four sensors in the
rear bumper.
1Sensors in the front bumper (Only visi-
ble without DISTRONIC Plus*)Range of the sensors!
The operational function of the Parktronic
system can be affected by dirty sensors, espe-
cially at times of snow and ice.
Make sure that the area on the bumpers around
the sensors is free of dirt, ice and/or slush,
otherwise Parktronic may not function properly,
see “Cleaning the Parktronic* system sensors”
(
page 619).
i
Interference caused by other ultrasonic sig-
nals (e.g. working jackhammers, car wash, or the
air brakes of trucks) can cause the system to
send erratic indications, and should be taken
into consideration.
i
To function properly, the sensors must be
free of dirt, ice, snow and slush. Clean the sen-
sors regularly, being careful not to scratch or
damage the sensors, see “Cleaning the Park-
tronic* system sensors” (
page 619).

476 Controls in detailDriving systems
Switching off the Parktronic sys-
tem: Press button 1.
Indicator lamp 2 comes on.

Switching on the Parktronic system:
Press button 1 again.
Indicator lamp 2 goes out.
Parktronic system malfunction
If only the red distance segments illumi-
nate and an acoustic warning sounds,
there is a malfunction in the Parktronic
system. The Parktronic system will auto-
matically switch off after 20 seconds and
the indicator lamp in the Parktronic switch
comes on.

Have the Parktronic system checked
by an authorized Mercedes-Benz Cen-
ter as soon as possible.
If only the red distance segments illumi-
nate and no acoustic warning sounds, the
Parktronic system sensors are dirty or
there is an interference from other radio or
ultrasonic signals. The Parktronic system
will automatically switch off after 20 sec-
onds and the indicator lamp in the Park-
tronic switch comes on.

Switch off the ignition (
page 370).

Clean the Parktronic system sensors
(page 619).

Switch on the ignition.
or

Check the Parktronic system operation
at another location to rule out interfer-
ence from outside radio or ultrasonic
signals.
Park Assist*
i
The Parktronic system is automatically
switched on when the ignition is switched on
(
page 370).
Warning!
G
Park Assist is a supplemental system. It is
not intended to, nor does it replace, the
need for extreme care. The responsibility
during parking and other critical maneuvers
always remains with the driver.Warning!
G
Make sure no persons or animals are in the
area in which you are maneuvering. You
could otherwise injure them.!
Special attention must be paid to objects
with smooth surfaces or low silhouettes (e.g.
trailer couplings, painted posts, elevated cross-
bars or road curbs). Such objects may not be de-
tected by the system and can damage the
vehicle.

481 Controls in detail
Driving systems

Switching off Park Assist system:
Press button 1.
Indicator lamp 2 comes on.

Switching on Park Assist system:
Press button 1 again.
Indicator lamp 2 goes out.
Advanced Parking Guidance*
Advanced Parking Guidance is an electron-
ic parking aid equipped with radar sensors
that scan the area on both sides of vehicle.
When suitable parking space is found it is
shown in the display and you receive steer-
ing instructions for parking in that space.
i
The Park Assist system is automatically
switched on when the ignition (
page 370) and
radar sensors are switched on (page 307).
Warning!
G
Advanced Parking Guidance is only an aid
and may display parking spaces that are not
suitable e.g. due to parking regulations, un-
suitable road/ground surfaces, driveways,
entrances/exits, etc.
Advanced Parking Guidance only shows a
representation of the parking space in the
instrument cluster display as parking space
is first initially measured when driving past.
Subsequent changes to the parking space
are not taken into account, e.g. if the posi-
tion of the vehicle parked in front of or be-
hind the space changes or objects in the
parking space are moved. Moving objects
are not shown, e.g. pedestrians or vehicles
driving past. Advanced Parking Guidance
does not relieve you of the responsibility to
pay attention. If you only rely on Advanced
Parking Guidance, you may cause an acci-
dent and injure yourself and others.
You are always responsible for safety and
must continue to pay attention to your im-
mediate surroundings when parking and
maneuvering.

489 Controls in detail
Driving systems
Switching on Rear View Camera
Switch on the ignition (
page 370).

Switch on COMAND (
page 87).

Move gear selector lever to reverse
gearR.
The COMAND display will show the
area behind the vehicle with guide
lines.
Warning!
G
Make sure no persons or animals are in the
area in which you are maneuvering. You
could otherwise injure them.Warning!
G
The Rear View Camera may not function if:

the trunk lid is not completely closed


it is raining or snowing heavily, or if
there is thick fog


in a very dark area


the camera is exposed to very strong
white light (white stripes may appear on
the COMAND display)


the surrounding area is lit with fluores-
cent light (the COMAND display can
flicker)


outside temperatures are very high (lens
condensation)


there is a sudden change in tempera-
ture, for example when you drive out of
the cold into a heated garage in winter
(lens condensation)


the camera lens is dirty or covered, see
“Cleaning the Rear View Camera* lens”
(page 621)


the rear of your vehicle is damaged. In
this case, have the position and setting
of the camera checked by a qualified
technician. Contact an authorized
Mercedes-Benz Center.
Do not use the Rear View Camera if the
roads are icy, slippery or covered with snow.
The vehicle could slip causing the actual ve-
hicle position to deviate from the one shown
on the COMAND display.
This may cause injury to you or others, or
damage the vehicle or objects.
Mounting tires/rims of other specification
than the original equipment tires/rims may
impair the function of the Rear View Cam-
era. Contact an authorized Mercedes-Benz
Center.
Warning!
G
Use of Rear View Camera can be dangerous
if you are color-blind or have impaired color
vision.
Only use Rear View Camera if you can see
and distinguish all colored guide lines shown
by Rear View Camera on the COMAND dis-
play.i
The Rear View Camera must be activated in
the instrument cluster control system in order
for it to be switched on (
page 303).


497 Controls in detail
Driving systems
Indicator and warning lamps
1Yellow indicator lamp/red warning
lamp
Switching on: Make sure that the ra-
dar sensors (
page 307) and Blind
Spot Assist (
page 304) are switched
on.
With the ignition switched on, the warn-
ing lamp1 in the exterior mirror lights
up red.
With the engine running, the indicator
lamp1 in the exterior mirror lights up
yellow up to a speed of 20 mph
(30 km/h).Once a speed above 20 mph (30 km/h)
has been reached and


Blind Spot Assist detects no vehicle in
its range, the indicator lamp1 goes
out


Blind Spot Assist detects another vehi-
cle in its range, the warning lamp1 on
the corresponding side of the vehicle
turns red.Collision warning
If a vehicle is detected in the Blind Spot As-
sist range and you activate the turn signal,
a two-tone warning will sound and the red
warning lamp1 will flash.

Remain on the lane that you are cur-
rently on until traffic conditions permit
to change.
If the turn signal remains on, the red warn-
ing lamp1 will flash to indicate that vehi-
cles have been detected. No further
audible warnings will sound.
Warning!
G
Blind Spot Assist is not active at speeds be-
low approximately 20 mph (30 km/h). You
will not be alerted to the presence of vehi-
cles in the monitored area at these speeds.
It is the driver’s responsibility at all times to
be attentive to road, weather and traffic con-
ditions and to provide the steering, braking
and other driving inputs necessary to retain
control of the vehicle. Failure to do so could
result in recognizing dangers too late, possi-
bly resulting in an accident and serious inju-
ry to yourself and others.
Warning!
G
Do not change lanes or make turns, while
the red warning lamp
1
is flashing. Doing
so could result in an accident and seroius in-
jury to yourself and others.

506 Controls in detailAutomatic climate controlRear window defroster
Activating
Switch on the ignition (
page 370).

Press button< (
page 501) up or
down.
The indicator lamp on the button
comes on.
Deactivating

Press button< (
page 501) up or
down.
The indicator lamp on the button goes
out.
Maximum cooling MAXCOOL (USA only)
If U is selected on both the left and
right side and there is a high demand for
cooling, the display “MAXCOOL” appears
in the COMAND display.
This provides the fastest possible cooling
of the vehicle interior (when windows and
tilt/sliding sunroof or tilt/sliding panel*
are closed).
Air recirculation mode
Switch to air recirculation mode to prevent
unpleasant odors from entering the vehicle
from the outside (e.g. before driving in a
tunnel). This setting cuts off the intake of
outside air and recirculates the air in the
passenger compartment.
!
The rear window defroster uses a large
amount of power. To keep battery drain to a min-
imum, switch off the defroster as soon as the
rear window is clear.
i
The defroster is automatically deactivated
after some time of operation depending on the
outside temperature.
Warning!
G
Any accumulation of snow and ice should be
removed from the rear window before driv-
ing. Visibility could otherwise be impaired,
endangering you and others.i
If the rear window defroster switches off too
soon and the indicator lamp goes out, this indi-
cates that too many electrical consumers are op-
erating simultaneously and the load on the
battery is reducing available voltage. The system
responds automatically by deactivating the rear
window defroster.
i
Maximum cooling MAXCOOL is only avail-
able when the engine is running.Warning!
G
Fogged windows impair visibility, endanger-
ing you and others. If the windows begin to
fog on the inside, switching off the air
recirculation mode immediately should clear
interior window fogging. If interior window
fogging persists, make sure the air
conditioning (
page 276) is activated, or
press button;.