sensor MERCEDES-BENZ S-Class 2008 W221 Comand Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2008, Model line: S-Class, Model: MERCEDES-BENZ S-Class 2008 W221Pages: 801, PDF Size: 10.23 MB
Page 582 of 801
581 Operation
Engine compartment
To open washer fluid reservoir: Pull
tab of cap1 upward.
Refill the reservoir with MB Windshield
Washer Concentrate and water (or
commercially available premixed wind-
shield washer solvent/antifreeze, de-
pending on ambient temperatures).
To close washer fluid reservoir:
Press cap1 onto filler hole until it en-
gages.
For more information, see “Windshield
washer system and headlamp cleaning
system” (
page 774).
Warning!
G
Washer solvent/antifreeze is highly flamma-
ble. Do not spill washer solvent/antifreeze
on hot engine parts, because it may ignite
and burn. You could be seriously burned.
!
Always use washer solvent/antifreeze
where temperatures may fall below freezing
point. Failure to do so could result in damage to
the washer system/reservoir.
Only use washer fluid which is suitable for plastic
lenses. Improper washer fluid can damage the
plastic lenses of the headlamps.
Do not use distilled or de-ionized water in the
washer fluid reservoir. Otherwise, the washer
fluid level sensor could be damaged.
Page 594 of 801
593 Operation
Tires and wheels
Install the valve cap.
Repeat this procedure for each tire.
Checking tire inflation pressure elec-
tronically with the Advanced Tire Pres-
sure Monitoring System
(Advanced TPMS)The TPMS only functions on wheels that
are equipped with the proper electronic
sensors. It monitors the tire inflation pres-
sure, as selected by the driver, in all four
tires. A warning is issued to alert you to a
decrease in pressure in one or more of the
tires.
Tire inflation pressure inquiries are made
using the multifunction display. The
present inflation pressures are displayed
only after a few minutes of travel time.
i
If you have overfilled the tire, release tire in-
flation pressure by pushing the metal stem of the
valve with e.g. a tip of a pen. Then recheck the
tire inflation pressure with the tire gauge.
i
The Advanced
Tire
Pressure
Monitoring
System (Advanced TPMS) is equipped with a
combination low tire pressure/TPMS malfunc-
tion telltale in the instrument cluster
(page 638). Depending on how the telltale illu-
minates, it indicates a low tire inflation pressure
condition or a malfunction in the TPMS system it-
self:
If the telltale illuminates continuously, one
or more of your tires is significantly under-in-
flated. There is no malfunction in the TPMS.
USA only:
If the telltale flashes for 60 seconds and
then stays illuminated, the TPMS system it-
self is not operating properly.
i
USA only:
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interfer-
ence, and
(2) this device must accept any interference re-
ceived, including interference that may
cause undesired operation.
Any unauthorized modification to this device
could void the user’s authority to operate the
equipment.
i
Canada only:
This device complies with RSS-210 of Industry
Canada. Operation is subject to the following
two conditions:
(1) This device may not cause interference, and
(2) this device must accept any interference re-
ceived, including interference that may
cause undesired operation of the device.
Any unauthorized modification to this device
could void the user’s authority to operate the
equipment.
i
Possible differences between the readings
of a tire inflation pressure gauge of an air hose,
e.g. gas station equipment, and the vehicle’s
control system can occur. Usually the readings
issued by the control system are more precise.
i
The menu overview can be found on
(
page 289).
Page 595 of 801
594 OperationTires and wheels
Switch on the ignition (
page 370).
Press( or& to select the menu
“Service”.
Press$ or% to select “Tire
Pressure”.
Press#.
i
When the message “Tire Pressures Dis-
played After Driving a Few Minutes” appears in
the display, the individual inflation pressure val-
ues are matched with the tires. The individual
values are displayed after a few minutes driving.Warning!
G
It is the driver’s responsibility to calibrate
the TPMS on the recommended cold infla-
tion pressure. Underinflated tires affect the
ability to steer or brake the vehicle. You
might lose control over the vehicle.
i
With a spare wheel without wheel sensor
mounted, the system may still indicate the tire
inflation pressure of the removed wheel for some
minutes. If this happens, keep in mind that the
indicated value where the spare wheel is mount-
ed does not reflect the actual spare tire inflation
pressure.
Warning!
G
The TPMS does not indicate a warning for
wrongly selected inflation pressures. Always
adjust tire inflation pressure according to
the Tire and Loading Information placard on
the driver’s door B-pillar or, if available, the
supplemental tire pressure information on
the inside of the fuel filler flap.
The TPMS is not able to issue a warning due
to a sudden dramatic loss of pressure (e.g.
tire blowout caused by a foreign object). In
this case bring the vehicle to a halt by care-
fully applying the brakes and avoiding
abrupt steering maneuvers.
Page 597 of 801
596 OperationTires and wheelsReactivating Advanced TPMS
The TPMS must be reactivated when you
have adjusted the tire inflation pressure to
a new level (e.g. because of different load
or driving conditions). The TPMS is then
recalibrated to the current tire inflation
pressures.
Using the tire Tire and Loading Informa-
tion placard on the driver’s door B-pillar
(page 585) or, if available, the sup-
plemental tire inflation pressure
information on the inside of the fuel fill-
er flap (
page 570), make sure the tire
inflation pressure of all four tires is cor-
rect.
Switch on the ignition (
page 370).
Press( or& to select the menu
“Service”.
Press$ or% to select “Tire
Pressure”.
Press#.
You will see
the current inflation pressures for
each tire
or
the message
“Tire Pressures
Displayed After Driving
a Few Minutes”
appear in the multifunction display.
Press%.
The message
“Use Current
Pressures As New
Reference Values
Press "OK" to Confirm
Tire Press.”
appears in the multifunction display.
Warning!
G
It is the driver’s responsibility to calibrate
the TPMS on the recommended cold infla-
tion pressure. Underinflated tires affect the
ability to steer or brake the vehicle. You
might lose control over the vehicle.
i
Reactivate the TPMS after adjusting the tire
inflation pressure to the inflation pressure rec-
ommended for the vehicle operating condition.
Tire inflation pressure should only be adjusted
on cold tires. Observe the recommended tire in-
flation pressure on the Tire and Loading Informa-
tion placard on the driver’s door B-pillar
(
page 585). Some vehicles may have supple-
mental tire inflation pressure information for
driving at high speeds (
page 591) or for vehi-
cle loads less than the maximum loaded vehicle
condition. If such information is provided, it can
be found on the inside of the fuel filler flap
(
page 570).
i
After wheel rotation or sensor replacement,
the vehicle must be parked for 20 minutes be-
fore attempting to reactivate the TPMS.
i
The menu overview can be found on
(
page 289).
Page 618 of 801
617 Operation
Vehicle care
Engine cleaning
Prior to cleaning the engine compartment,
make sure to protect electrical compo-
nents and connectors from contact with
water and cleaning agents.
Corrosion protection, such as
MB Anticorrosion Wax, should be applied
to the engine compartment after every
engine cleaning. Before applying, all
control linkage bushings and joints should
be lubricated. The poly-V-belt and all pul-
leys should be protected from any wax.
Vehicle washing
In the winter, thoroughly remove all traces
of road salt as soon as possible.
When washing the vehicle underbody, do
not forget to clean the inner sides of the
wheels.Hand-wash
Do not use hot water or wash your vehicle
in direct sunlight.
Only use a mild car wash detergent,
such as Mercedes-Benz approved Car
Shampoo.
Thoroughly spray the vehicle with a dif-
fused jet of water.
Direct only a very weak spray towards
the ventilation intake.
Use plenty of water and rinse the
sponge and chamois frequently.
Rinse with clean water and thoroughly
dry with a chamois.
Do not allow cleaning agents to dry on
the finish.Automatic car wash
You can have your car washed in an auto-
matic car wash from the start. Automatic
car washes without brushes are prefera-
ble.
To protect the filter system, switch the
automatic climate control to air recir-
culation mode (
page 506).
If the vehicle is very dirty, prewash it be-
fore running it through the automatic car
wash.
i
Vehicles with KEYLESS-GO*:
If a door handle is hit by a strong jet of water, and
a SmartKey with KEYLESS-GO* is in close prox-
imity, i.e. within approximately 3 ft (approxi-
mately 1 m), the vehicle could be inadvertently
locked or unlocked.
!
Do not use scouring agents on these parts.
Never apply strong force and only use a soft,
non-scratching cloth when cleaning the vehicle.
Do not attempt to wipe the surface with a dry
cloth or sponge.
Otherwise you may scratch or damage the paint.
!
Do not clean your vehicle in an automatic
touchless car wash which uses caustic spray.
Otherwise the caustic spray will damage the
paint or ornamental moldings.
!
Make sure that the windshield wiper switch
is set to0 (
page 408). Otherwise, e.g. the rain
sensor could activate and cause the wipers to
move unintentionally. This may lead to vehicle
damage.
Due to the width of the vehicle, fold in exterior
rear view mirrors prior to running the vehicle
through an automatic car wash to prevent dam-
age to the mirrors.
Page 620 of 801
619 Operation
Vehicle care
Headlamps, tail lamps, side markers,
turn signal lenses
Use a mild car wash detergent, such as
Mercedes-Benz approved Car
Shampoo, with plenty of water.Cleaning the DISTRONIC Plus*/
PRE-SAFE
® Brake* system sensors
(USA only)
The sensors are integrated in the front
bumpers and cannot be seen from the out-
side.
1Sensor cover
2Bumper area near sensors
Switch off the ignition (
page 370).
Use a mild car wash detergent, such as
Mercedes-Benz approved Car
Shampoo, with plenty of water and a
non-scratching cloth to clean sensor
cover1.
Clean a wide area of the bumpers sur-
rounding the sensor2.
Cleaning the Parktronic* system
sensors
1Parktronic system* sensors in front
bumper
!
Only use window cleaning solutions that are
suitable for plastic lamp lenses. Window clean-
ing solutions which are not suitable may damage
the plastic lamp lenses of the headlamps. There-
fore, do not use abrasives, solvents or cleaners
that contain solvents.
Never apply strong force and only use a soft,
non-scratching cloth when cleaning the lenses.
Do not attempt to wipe dirty lenses with a dry
cloth or sponge.
Otherwise you may scratch or damage the lens
surface.
!
To prevent scratches or damage, never
apply strong force and only use a soft,
non-scratching cloth when cleaning the sensor
cover and/or bumper area near sensors. Do not
attempt to wipe dirty sensors and/or bumper
with a dry cloth or sponge.
Page 621 of 801
620 OperationVehicle care
Use a mild car wash detergent, such as
Mercedes-Benz approved Car Sham-
poo, with plenty of water and a soft,
non-scratching cloth to clean
sensors1 on the bumpers.Cleaning the driving systems sensors
The sensors are integrated in the front and
rear bumpers and cannot be seen from the
outside. They work with the following sys-
tems:
BAS Plus*
PRE-SAFE
® Brake*
Blind Spot Assist*
Park Assist*
Advanced Parking Guidance*
1Bumper area near sensors
Switch off the ignition (
page 370).
Use a mild car wash detergent, such as
Mercedes-Benz approved Car Sham-
poo, with plenty of water and a soft,
non-scratching cloth to clean the
bumper area near sensors.
!
Do not apply strong pressure to the sensor
covers. Applying strong pressure may damage
the sensor covers.
Follow the instructions provided by the power
washer manufacturer on maintaining a distance
between the vehicle and the nozzle of the power
washer.
!
To prevent scratches, never apply strong
force and only use a soft, non-scratching cloth
when cleaning the sensors. Do not attempt to
wipe dirty sensors with a dry cloth or sponge.
Page 622 of 801
621 Operation
Vehicle care
Cleaning the Rear View Camera* lens
1Camera lens
Only use clean water and a soft,
non-scratching cloth to clean the cam-
era lens1.
Be careful not to apply wax to the camera
lens1 when waxing the vehicle. If neces-
sary, remove the wax using the
Mercedes-Benz approved Car Shampoo
with plenty of water.Cleaning the windshield in front of the
Night View Assist camera*
1Recessed handles of camera cover
Use recessed handles1 to swing
camera cover downward.
!
To prevent scratches or damage to the sur-
face, never apply strong force and only use a
soft, non-scratching cloth when cleaning the
bumper area near sensors. Do not attempt to
wipe a dirty bumper with a dry cloth or sponge.
!
Do not clean the camera and the area
around the camera:
with a high-pressure cleaner
with a dry cloth and high pressure
with aggressive cleaning agents
You could otherwise damage the camera.Warning!
G
Please do not forget that your primary re-
sponsibility is to drive the vehicle. A driver’s
attention to the road must always be
his/her primary focus when driving. For
your safety and the safety of others, stop be-
fore trying to remove window fogging or
cleaning the window in front of the Night
View Assist camera.
Bear in mind that at a speed of just 30 mph
(approximately 50 km/h), your vehicle is
covering a distance of 44 feet (approximate-
ly 14 m) every second.
!
Do not clean the lens of the Night View
Assist camera. If the camera lens is dirty, please
contact a qualified specialist workshop such as a
Mercedes-Benz Center.
Page 645 of 801
644 Practical hintsWhat to do if …?Text messagesDisplay
Possible cause/consequence
Possible solution
Apply Brake
to Shift
from 'P'
You have tried to shift the auto-
matic transmission to drive po-
sition D, reverse gearR or
neutral positionN without step-
ping on the brake.
Step on brake.
Check
Child Seat Position
See Oper. Manual
(Canada only)
The child seat is not positioned
correctly.
Fasten the seat in the correct position.
The sensor for the child seat is
malfunctioning.
Have the sensor for child seat detection checked at an authorized
Mercedes-Benz Center.
Page 647 of 801
646 Practical hintsWhat to do if …?Display
Possible cause/consequence
Possible solution
DISTRONIC PLUS
Currently Unavailable
See Oper. Manual
DISTRONIC Plus* is switched off and is
temporarily unavailable.
DISTRONIC Plus* is deactivated if:
the DISTRONIC Plus* cover in the radi-
ator grille is dirty
the radar sensors* do not sense any
other vehicles or objects, i.e. road sign
or similar to this, for a long time
the system is overheated
its function is impaired as a result of
heavy precipitation or fog
the battery voltage is insufficient
Clean the DISTRONIC Plus* cover in the radiator grille
(page 619).
Restart the vehicle.
Try activating DISTRONIC Plus* again later.
Wait until the system cools down or the battery recovers.
DISTRONIC Plus* will be operational again without you needing to
restart the engine if:
the dirt (e.g. slush) loosens while you are driving
the system detects that the radar sensors* are fully available
again
the message in the multifunction display disappears
DISTRONIC Plus* is switched off because
the radar sensor system* is temporarily in-
operative due to electromagnetic interfer-
ence near television and radio transmitter
stations, toll stations, speed measuring
systems, etc.
Wait until the message in the multifunction display disappears.
DISTRONIC PLUS
Inoperative
DISTRONIC Plus* is malfunctioning.
BAS Plus* and PRE-SAFE
® Brake* are also
not available.
Contact an authorized Mercedes-Benz Center as soon as pos-
sible.