lock MERCEDES-BENZ S-Class 2008 W221 Comand Manual

408 Controls in detailWindshield wipersCombination switch1Switching on windshield wipers
2Single wipe
Wiping with windshield washer fluid

Switch on the ignition (
page 370).
Switching on/off windshield wipers
Turn the combination switch to the
desired position depending on the
intensity of the rain.
MWindshield wipers off
USlow intermittent wiping
(rain sensor operation with low
sensitivity)
VFast intermittent wiping
(rain sensor operation with high
sensitivity)
uSlow continuous wiping
tFast continuous wiping
!
If the windshield wipers leave smears on the
windshield after the car has been driven through
an automatic car wash, then wax or other resi-
due is on the windshield. Shortly after washing
the car in an automatic car wash, clean the wind-
shield with windshield washer fluid
(
page 409).
!
Do not operate the windshield wipers when
the windshield is dry. Dust that accumulates on
a windshield might scratch the glass and/or
damage the wiper blades when wiping occurs on
a dry windshield. If it is necessary to operate the
windshield wipers in dry weather conditions, al-
ways operate the windshield wipers with wind-
shield washer fluid (
page 409).
!
If anything blocks the windshield wipers
(leaves, snow, etc.), switch them off immediate-
ly.


For safety reasons, stop the vehicle in a safe
location and,

remove SmartKey from starter switch
or


turn off the engine by pressing the
KEYLESS-GO* start/stop button
(page 372) and open the driver’s door
(with the driver’s door open, starter
switch is in position0, same as with
SmartKey removed from starter switch)
before attempting to remove any blockage.


Remove blockage.


Turn the windshield wipers on again.If the windshield wipers fail to function at all in
the combination switch position U or V,


set the combination switch to the next
higher wiper speed


have the windshield wipers checked at the
nearest authorized Mercedes-Benz Center

410 Controls in detailPower windowsOpening and closing power windows
The door windows are opened and closed
electrically. The switches

for all door windows are on the driver’s
door


for the front passenger side window
are on the front passenger door


for each rear side window are on the
rear doors1Left front door window
2Right front door window
3Left rear door window
4Right rear door window
Warning!
G
Do not keep any part of your body up against
the side window pane when opening a win-
dow. The downward motion of the pane may
pull that part of your body down between
the window pane and the door frame and
trap it there. If there is a risk of entrapment,
release the switch and press it again to
close the window.
Warning!
G
When closing the windows, make sure that
there is no danger of anyone being harmed
by the closing procedure.
Activate the override switch (
page 64)
when children are riding in the back seats of
the vehicle. The children may otherwise in-
jure themselves, e.g. by becoming trapped
in the window opening.
The closing of the door windows can be im-
mediately halted by releasing the switch or,
if the switch was pressed past the resis-
tance point and released, by pressing the
lower part of the respective switch again.
The door windows are equipped with the ex-
press-close and automatic reversal func-
tion. If the window encounters an
obstruction that blocks its path in a circum-
stance where you pressed the switch past
the resistance point and released it to close
the window, the automatic reversal function
will stop the window and open it slightly.

411 Controls in detail
Power windows

Switch on the ignition (
page 370).

Opening: Press the lower part of
switch1 to 4 (
page 410) to the re-
sistance point.
The corresponding window will move
downwards until you release the
switch.

Closing: Press the upper part of
switch1 to 4 (
page 410) to the re-
sistance point.
The corresponding window will move
upwards until you release the switch.
If the window encounters an obstruction
that blocks its path in a circumstance where
you are closing the window by pressing and
holding the switch, by pressing and holding
button ‹ on the SmartKey or SmartKey
with KEYLESS-GO*, by pressing and holding
the sensor surface (vehicles with
KEYLESS-GO*) on an outside door handle,
or by pressing and holding button, on
the climate control panel, the automatic re-
versal function will not operate.
When leaving the vehicle, always remove the
SmartKey or SmartKey with KEYLESS-GO*
from the starter switch, take it with you, and
lock the vehicle. Do not leave children unat-
tended in the vehicle, or with access to an
unlocked vehicle. A child’s unsupervised ac-
cess to a vehicle could result in an accident
and/or serious personal injury.
i
You can also open or close the windows us-
ing the SmartKey, see “Summer opening fea-
ture” (page 412) and “Convenience closing
feature” (page 413).
Depending on current position, the windows may
also open or close when the air recirculation
button, (page 501) is pressed and held
for 2 seconds.
i
Operating the windows from the rear is not
possible if you activate the override switch
(
page 64).
i
If PRE-SAFE
® has been activated, the door
windows close automatically until only a small
gap remains.
i
With the SmartKey in starter switch
position0 or removed from the starter switch,
the power windows can be operated:


until you open the driver’s or front passenger
door


for at least 5 minutes if no door was opened
Warning!
G
If you press and hold the switch up when
closing the window, and upward movement
of the window is blocked by some obstruc-
tion including but not limited to arms, hands,
fingers, etc., the automatic reversal will not
operate.


412 Controls in detailPower windows
Express-opening: Press the lower part
of switch1 to4 (
page 410) past
the resistance point and release.
The corresponding window opens com-
pletely.

Express-closing: Press the upper part
of switch1 to4 (
page 410) past
the resistance point and release.
The corresponding window closes com-
pletely.

Stopping during Express-operation:
Briefly press the respective power win-
dow switch again.
Rear side window sunshades*
Closing: With the side window fully
closed, press the upper part of
switch3 or4 (
page 410).
The rear side window sunshade will be
fully closed.

Opening: Press the lower part of
switch3 or4 (
page 410).
The rear side window sunshade will be
fully opened.
Summer opening feature
If the weather is warm, you can ventilate
the vehicle before driving off by simulta-
neously:

opening the door windows and rear
side window sunshades*


opening the tilt/sliding sunroof or
tilt/sliding panel* and extending the
roller sunblinds*


turning on the seat ventilation* for the
driver’s seat
Warning!
G
Driver’s door only:
If within 5 seconds you again press the
switch past the resistance point and re-
lease, the automatic reversal will not oper-
ate.
!
If the upward movement of the window is
blocked during the closing procedure, the win-
dow will stop and open slightly. Remove the ob-
struction, press the respective power window
switch at the upper part again past the resis-
tance point and release. If the window still does
not close when there is no obstruction, press
and hold the respective power window switch at
the upper part. The side window will then close
without the obstruction sensor function.
i
The rear side window sunshade cannot be
partially closed.
i
The switches on the rear doors can also be
used to close the rear side window sunshades on
the other side of the vehicle.
i
The switches on the driver’s door take pre-
cedence over the rocker switches on the other
doors.


413 Controls in detail
Power windows

Aim transmitter eye of the SmartKey or
SmartKey with KEYLESS-GO* at the
driver’s outside door handle. The
SmartKey or SmartKey with
KEYLESS-GO* must be in close proxim-
ity to the driver’s door handle.Vehicles with tilt/sliding sunroof

Press and hold button Πuntil the
door windows and tilt/sliding sunroof
have reached the desired position.

Release button Πto interrupt pro-
cedure.
Vehicles with panorama roof* and/or
rear side window sunshades*
If roller sunblinds are retracted and/or
rear side window sunshades* are closed:

Press and hold button
Œ
. The win-
dows and sunblinds and/or rear side
window sunshades* begin to open/ex-
tend after approximately 1 second.

With the windows and roller blinds
and/or rear side window sunshades*
fully opened/extended, press and hold
button
Œ
again. The tilt/sliding pan-
el tilts and opens.If roller sunblinds and/or rear side window
sunshades* are open/extended:

Press and hold button
Œ
. The win-
dows move down and the tilt/sliding
panel tilts and opens after approxi-
mately 1 second.

Release button
Œ
to interrupt proce-
dure.
Convenience closing feature
When you lock the vehicle, you can close
the door windows and tilt/sliding sunroof
or tilt/sliding panel* simultaneously.
Afterward, you can close the roller sun-
blinds* of the panorama tilt/sliding sun-
roof* and the rear side window
sunshades*.
i
The “Summer opening” function can only be
activated via the remote control of the SmartKey
or SmartKey with KEYLESS-GO*.
i
The seat ventilation* for the driver’s seat is
automatically set to the highest level if activated
via summer opening feature.
i
The function of the SmartKey overrules the
KEYLESS-GO function.

417 Controls in detail
Driving and parking
For more information on how to operate
the gear selector lever, see “Automatic
transmission” (
page 426).
Starting with the SmartKey

Make sure the automatic transmission
is set to park positionP.
The gear position indicator in the multi-
function display should be on park
positionP.

Do not depress accelerator.

Turn the SmartKey in the starter switch
to position3 and hold until the engine
starts (
page 370).
For information on turning off the engine
with the SmartKey, see “Turning off the en-
gine” (
page 424).Starting with KEYLESS-GO*
You can start your vehicle without the
SmartKey in the starter switch using the
KEYLESS-GO start/stop button on the
starter switch.
The SmartKey with KEYLESS-GO must be
located in the vehicle.
KEYLESS-GO start/stop button1USA only
2Canada only
Make sure KEYLESS-GO start/stop
button is inserted in the starter switch
(page 371).

Make sure the automatic transmission
is set to park positionP.
The gear position indicator in the multi-
function display should be on park
positionP.

Depress the brake pedal during the
starting procedure.

Do not depress accelerator.
i
You can also use the “touch-start” function.
Turn the SmartKey to position3 and release it
again immediately. The engine then starts auto-
matically.
i
You can also start the engine with the auto-
matic transmission set to neutral positionN.
Warning!
G
As long as the SmartKey with KEYLESS-GO
is in your vehicle, the vehicle can be started.
Therefore, never leave children unattended
in the vehicle, as they could otherwise acci-
dentally start the engine.
When leaving the vehicle, always take the
SmartKey with KEYLESS-GO with you and
lock the vehicle. Do not leave children unat-
tended in the vehicle, or with access to an
unlocked vehicle. A child’s unsupervised ac-
cess to a vehicle could result in an accident
and/or serious personal injury.


419 Controls in detail
Driving and parking
Driving off
Depress the brake pedal.
The gear selector lever can now be
used.

Shift the automatic transmission to
drive positionD or reverse gearR.

Release the brake pedal.

Carefully depress the accelerator
pedal.
The electronic parking brake is auto-
matically released (
page 422).
The red brake warning lamp 0
(USA only) or ! (Canada only) in the
instrument cluster goes out.After a cold start, the automatic transmis-
sion shifts at a higher engine revolution.
This allows the catalytic converter to reach
its operating temperature earlier.
i
Wait for the gear selection process to com-
plete before setting the vehicle in motion.
i
Shifting from park positionP to reverse
gearR, neutral positionN, or drive positionD is
only possible with the brake pedal depressed.
Without the brake pedal depressed, the gear se-
lector lever can be moved, but the parking pawl
remains engaged, not allowing shifting to occur.
!
If you hear a warning signal, the red indica-
tor lamp 0 (USA only) or ! (Canada only)
in the instrument cluster flashes and the mes-
sage “Please Release Parking Brake” appears in
the multifunction display when driving off, you
are driving with the electronic parking brake en-
gaged, or you are carrying out an emergency
brake application with the electronic parking
brake.
Release the electronic parking brake
(
page 422).
i
Once the vehicle is in motion, the automatic
central locking system engages and the locking
knobs in the doors move down.
The automatic door lock feature can be deacti-
vated (page 267).
You can open a locked door from the inside.
Open door only when conditions are safe to do
so.
Warning!
G
On slippery road surfaces, never downshift
in order to obtain braking action. This could
result in drive wheel slip and reduced vehi-
cle control. Your vehicle’s ABS will not pre-
vent this type of loss of control.Warning!
G
It is dangerous to shift the gear selector le-
ver out of park positionP or neutral
positionN if the engine speed is higher than
idle speed. If your foot is not firmly on the
brake pedal, the vehicle could accelerate
quickly forward or in reverse. You could lose
control of the vehicle and hit someone or
something. Only shift into gear when the en-
gine is idling normally and when your right
foot is firmly on the brake pedal.

422 Controls in detailDriving and parking
Electronic parking brake


Shift the automatic transmission to park
positionP.


Slowly release brake pedal.


When parked on an incline, turn front
wheels towards the road curb.


Turn the SmartKey to starter switch
position0 and remove, or press
KEYLESS-GO* start/stop button
(page 372).


Take the SmartKey or the SmartKey with
KEYLESS-GO* with you and lock vehicle
when leaving.
Warning!
G
When leaving the vehicle, always remove the
SmartKey or SmartKey with KEYLESS-GO*
from the starter switch, take it with you and
lock the vehicle. Do not leave children unat-
tended in the vehicle, or with access to an
unlocked vehicle. Children could release the
electronic parking brake and/or shift the
automatic transmission out of park
positionP, either of which could result in an
accident and/or serious personal injury.
Warning!
G
Getting out of your vehicle with the automat-
ic transmission not fully engaged in park
positionPis dangerous. Also, when parked
on an incline, park position P alone may not
prevent your vehicle from moving, possibly
hitting people or objects.
Always engage the electronic parking brake
in addition to shifting to park positionP
(page 416).
When parked on an incline, turn front wheels
towards the road curb.


430 Controls in detailAutomatic transmissionTransmission positions
The current transmission position appears
in the multifunction display.
1Current transmission position!
If the current transmission position does not
appear in the multifunction display due to a
malfunction, for example, make sure that the
automatic transmission is in the desired position
by carefully driving off with the transmission in
drive positionD and program modeS
(
page 436) selected. Do not limit the gear
range.
Effect
ì
Park position
Shift into park positionP only
when vehicle is stopped. The
park position is not intended to
serve as a brake when the vehi-
cle is parked. Rather, the driver
should always engage the elec-
tronic parking brake in addition
to shifting into park positionP to
secure the vehicle.
If the vehicle’s electrical system
is malfunctioning, the automatic
transmission could remain
locked in park positionP.
Have the vehicle checked as
soon as possible by an autho-
rized Mercedes-Benz Center.
!
SmartKey:
If you turn off the engine using the SmartKey and


remove the SmartKey from the starter
switch
or


open a front door
the transmission will shift to park positionP
automatically.
Keep in mind that turning off the engine with the
SmartKey alone only will automatically shift the
transmission to neutral positionN.
!
KEYLESS-GO*:
If you turn off the engine using the KEYLESS-GO
start/stop button and open a front door, the
transmission will shift to park positionP
automatically.
Keep in mind that turning off the engine using
the KEYLESS-GO start/stop button alone only
will automatically shift the transmission to
neutral positionN.

433 Controls in detail
Automatic transmission
Driving tips
Accelerator position
Your driving style influences the
transmission’s shifting behavior:
Less throttle Earlier upshifting
More throttle Later upshifting
Kickdown
Use kickdown when you want maximum
acceleration.
Press the accelerator past the point of
resistance.
Depending on the engine speed the
transmission shifts into a lower gear.

Ease on the accelerator when you have
reached the desired speed.
The transmission shifts up again.
Effect
ê
Drive
The transmission shifts
automatically. All forward gears
are available.
Warning!
G
Getting out of your vehicle without shifting
into park positionP is dangerous. Also, park
positionP alone is not intended to or capa-
ble of preventing your vehicle from moving,
possibly hitting people or objects.
Always engage the electronic parking brake
(page 422) in addition to shifting to park
positionP.
When parked on an incline, turn the front
wheels towards the road curb.
Do not park this vehicle in areas where com-
bustible materials such as grass, hay or
leaves can come into contact with the hot
exhaust system, as these materials could be
ignited and cause a vehicle fire.
Warning!
G
When leaving the vehicle, always remove the
SmartKey or SmartKey with KEYLESS-GO*
from the starter switch, take it with you, and
lock the vehicle. Do not leave children unat-
tended in the vehicle, or with access to an
unlocked vehicle. Children could shift the
automatic transmission out of park
positionP, which could result in an accident
and/or serious personal injury.