clock MERCEDES-BENZ S-Class 2013 W221 Owner's Manual

of more than 9 mph (15 km/h), the vehicle
locks automatically.
You could therefore be locked out when:
R
the vehicle is being pushed.
R the vehicle is being towed.
R the vehicle is being tested on a
dynamometer.
You can switch off the automatic locking
function via COMAND (Y page 269).Power closing feature
The power closing feature pulls the doors and
trunk lid into their locks automatically even if
they are only partly closed. G
WARNING
To prevent possible personal injury, always
keep hands and fingers away from the door or
trunk opening when closing a door or the
trunk lid. Be especially careful when small
children are around.
If danger threatens, pull the inside or outside
door handle, or pull the trunk lid handle.
To prevent personal injury, never activate the
closing assist mechanism by tampering with
the door or trunk lid latch. G
WARNING
Only drive with the doors closed. Otherwise,
one or more of the doors could open while the
vehicle is in motion, putting you and/or
others at risk. G
WARNING
Make sure the trunk lid is closed when the
engine is running and while driving. Among
other dangers, deadly carbon monoxide (CO)
gases may enter the vehicle interior resulting
in unconsciousness and death. X
Power closing feature (doors): push the
door past the first detent position of the
lock.
The power closing feature will pull the door
fully closed.
X Power closing feature (trunk lid): lightly
push the trunk lid closed.
The power closing feature will pull the trunk
lid fully closed. Unlocking the driver's door
(mechanical key)
If the vehicle can no longer be unlocked with
the SmartKey, use the mechanical key.
If you use the mechanical key to unlock and
open the driver's door, the anti-theft alarm
system will be triggered (Y page 79).
X Take the mechanical key out of the
SmartKey (Y page 84).
X Insert the mechanical key into the lock of
the driver's door as far as it will go. X
Firmly turn the mechanical key
counterclockwise as far as it will go to
position 0005and hold it in this position.
X Pull the door handle quickly.
The locking knob pops up.
The door is unlocked.
X Turn the mechanical key back and remove
it.
X Pull the door handle again.
X Insert the mechanical key into the
SmartKey. 90
DoorsOpening/closing

Even with the SmartKey removed from the
starter switch or the SmartKe
ywith KEYLESS-
GO removed from the vehicle, the remote
trunk opening/closing switch can be
operated. Therefore, do not leave children
unattended in the vehicle, or with access to
an unlocked vehicle. Achild's unsupervised
access to a vehicle could result in an accident
and/or serious personal injury. G
WARNING
Make sure the trunk lid is closed when the
engine is running and while driving. Among
other dangers, deadly carbon monoxide (CO)
gases may enter the vehicle interior resulting
in unconsciousness and death.
You can open and close the trunk lid from the
driver's seat when the vehicle is stationary
and unlocked. X
To open: press remote operating switch for
trunk lid 0002until the trunk lid opens.
X To close: press remote operating switch
for trunk lid 0002until the trunk lid is closed. Locking the trunk separately
You can lock the trunk separately.Ify ou then
unlock the vehicle centrally, the trunk
remains locked and cannot be opened.
X Close the trunk lid.
X Take the mechanical key out of the
SmartKey (Y page 84). X
Insert the mechanical key into the trunk lid
lock as far as the stop.
X Turn the mechanical key clockwise from
position 0005to position 0006.
X Remove the mechanical key.
X Insert the mechanical key into the
SmartKey. Unlocking the trunk (mechanical key)
! The trunk lid swings upwards when
opened. Therefore, make sure that there is
sufficient clearance above the trunk lid.
If the trunk cannot be unlocked with the
SmartKey or KEYLESS-GO, use the
mechanical key.
If you use the mechanical key to unlock and
open the trunk lid, the anti-theft alarm system
will be triggered (Y page 79).
X Take the mechanical key out of the
SmartKey (Y page 84).
X Insert the mechanical key into the trunk lid
lock as far as the stop. 94
TrunkOpening/closing

X
Turn the mechanical key counter-clockwise
from position 0005as far as it will go to
position 0006.
The trunk is unlocked.
X Turn the mechanical key back to position
0005 and remove it.
X Insert the mechanical key into the
SmartKey. Trunk emergency release
You can open the trunk lid from inside the
vehicle with the emergency release button. X
Briefly press emergency release
button 0002.
The trunk lid unlocks and opens.
The trunk lid can be unlocked and opened
with the trunk lid emergency release when
the vehicle is stationary or while driving.
Trunk lid emergency release light:
R emergency release button 0002flashes for
30 minutes after the trunk lid is opened
R emergency release button 0002flashes for
60 minutes after the trunk lid is closed.
The trunk lid emergency release does not
open the trunk lid if the battery is
disconnected or discharged. Side windows
Important safety notes
G
WARNING
When opening or closing the door windows,
make sure that there is no danger of anyone
being harmed by the opening/closing
procedure.
The door windows are equipped with
automatic operation and the anti-entrapment
feature. If in automatic mode a door window
encounters an obstruction that blocks its
path, the anti-entrapment feature will stop the
door window and open it slightly.
The door windows operate differently when
the switch is pulled. See the "Problems with
door windows" section for details.
The closing of the door windows can be
immediately halted by releasing the switch or,
if the switch was pulled past the resistance
point and released, by either pressing or
pulling the respective switch.
Activate the override switch when children
are riding in the back seats of the vehicle. The
children may otherwise injure themselves,
e.g. by becoming trapped in the door window
opening. G
WARNING
Do not keep any part of your body up against
the window pane when opening a window. The
downward motion of the pane may pull that
part of your body down between the window
pane and the door frame and trap it there. If
there is a risk of entrapment, release the
switch and pull it to close the window. Side windows
95Opening/closing Z

The COMAND controller can be:
R
pressed briefly or pressed and held 0021
R turned clockwise or counter-clockwise
0031001C0032
R slid left or right 003C001C003D
R slid forwards or back 002A001C0006
R slid diagonally 003A001C0030
In the instructions, operating sequences are
described as follows:
X Press the 0010button.
Audio mode is activated.
X Select Audio by sliding
001C0006and turning
0031001C0032 the COMAND controller and press
0021 to confirm.
The audio menu appears.
Back button 0002
Back button
X To exit the menu: press back button0002
briefly.
COMAND changes to the next higher menu
level in the curren toperating mode. i
You can also exit a menu by sliding 003C001C003D
or 002A001C0006 the COMAND controller.
X To switch to the basic display: press and
hold back button 0002.
COMAND changes to the basic display of
the curren toperating mode.
Function buttons The COMAND function buttons allow you to
select a main function directly.
0002
Function button for roller sunblind
0003 Function button for radio and CD/DVD or
SD card
0026 Back button
0025 Lumbar support/multicontour seat
0023 Function button for telephone and
navigation system
0024 On/off button for COMAND
0014 Volume control
0015 Programmable button (Y page 124)
Example:
X To select the radio or CD menu
directly: press0010button 0003once or
twice. At
ag lance
123COMAND Z

switch SPLITVIEW on and off
(Y
page 129).
The SPLITVIEW screen remains on for
approximately 30 minutes after the SmartKey
has been turned to position 0in the ignition
lock. After this time or after the SmartKey has
been removed, the settings on the front-
passenger side are saved for approximately
30 minutes longer. After this period,
reactivation on the front-passenger side
means that the settings from the driver's side
will be used.
Cordless headphones for the front
passenger There are different cordless headphones for
the front passenger and the rear
compartment.
The cordless headphones for the front
passenger can be identified by SPLITVIEW
symbol
0002on the headband.
The cordless headphones for the front
passenger cannot be used in the rear
compartment.E qually, the headphones for
the rear compartment cannot be used by the
fron tpassenger.
Swiveling the COMAND displa yand
setting the brightness You can swivel the COMAND display
5
.T he
buttons are located beside the COMAND
display. Swiveling
0002
To swivel the display to the left
0003 To swivel the display to the right
Setting the brightness 0002
Brightness of the instrument cluster
lighting
0003 Brightness of the COMAND display
Brighter or dimmer:
X Turn control 0002or0003 clockwise or counter-
clockwise.
i If Night View Assist Plus is activated, only
the brightness of the multifunction display
is adjusted with control 0002.
Display design
When the default settings are selected, the
display automatically switches between day
design and night design.
You can change these settings using
COMAND (Y page 147).
5 Not with SPLITVIEW. 128
At
ag lanceCOMAND

on the same street:
call up an address
destination fro mthe last destinations.
X Select Change by turning
0031001C0032and sliding
002A001C0006 the COMAND controller and press
0021 to confirm.
All destination entry functions are
available.
X Edit/enter the destination as described for
destination entry (Y page 157).
Entering adestination usin gthe map Calling up the map
X
To activate navigation mode: press the
0011 function button once or twice.
X To show the menu: press0021the COMAND
controller.
X Select Destination in the navigation
system menu bar by turning 0031001C0032the
COMAND controlle rand pressing 0021to
confirm.
X Select Via Map and press
0021to confirm.
You see the map with the crosshair. 0002
Current vehicle position
0003 Crosshair
0026 Details of the crosshair position
0025 Map scale selected
Display 0026depends on the settings selected
in "Map informatio ninthe display"
(Y page 189). The current street name can
be shown, provided the digital map contains
the necessary data, or the coordinates of the
crosshair if the geo-coordinate display is switched on and the GPS signal is strong
enough.
Moving the map and selecting the
destination
X
To scroll the map: slide003C001C003D, 002A001C0006or
003A001C0030 the COMAND controller.
X To set the map scale: as soon as you turn
0031001C0032 the COMAND controller, the scale bar
appears.
X Turn 0031001C0032 until the desired scale is set.
Turning clockwise zooms out from the map;
turning counter-clockwise zooms in.
X To selectad estination:press0021the
COMAND controller once or several times.
You will see either the address entry menu
with the destination address or, if COMAND
is unable to assign a unique address, a
selectio nlist. X
Selec tadestination by turning 0031001C0032the
COMAND controller and press 0021to
confirm.
If the destination is within the limits of the
digital map, COMAND attempts to assign
the destination to the map.
If the destination can be assigned, you will
see the address entry menu with the
address of the destination. If not, you will
see the entry Destination from Map .
X To start route calculation: selectStart and press
0021to confirm. 164
NavigationCOMAND

Displaying program information
X
Select Audio in the main function bar by
sliding 002A001Cand turning 0031001C0032the COMAND
controller and press 0021to confirm.
X Select Audio by sliding
002A001Cthe COMAND
controller and pressing 0021to confirm.
The audio menu appears.
X Select HD Radio by sliding
002A001Cthe
COMAN Dcontroller and press 0021to
confirm.
X Select Info in the HD Radio display by
sliding 002A001Cthe COMAND controller and
press 0021to confirm.
Information on the currently selected
station is displayed. The contents and
purpose of the information depend on the
HD Radio station. Satellite radio
Important notes This section provides detailed information on
the following topics:
R selecting a channel and program category
R memory functions
R sound settings
i The satellite radio mode described below
requires optionally available satellite radio
equipment and registration with a satellite
radio provider.
i Note that the categories and channels
shown in the illustrations depend on the
program content offered by the provider.
The program contents may vary. The
illustrations and descriptions in these
operating instructions may therefore differ
from the channels and categories offered
by the provider.
Satellite radio mode may be temporarily
unavailable or interrupted for a variety of
reasons. These reasons include
environmental or topographical conditions
as well as other issues beyond the control of Mercedes-Benz USA, LLC. Operation
may also be impaired in certain locations
(e.g. tunnels, multi-storey car parks or
within as well as close to buildings).
i SIRIUS XM Radio offers more than 130
digital-quality radio channels providing
100% commercial-free music, sport, news
and entertainment.
SIRIUS XM Radio employs a fleet of high-
performance satellites to broadcast around
the clock throughout the USA and Canada.
The satellite radio program is available for
a monthly fee. Details are available from
the SIRIUS XM Service Center and at
http://www.sirius.com (USA) or
http://www.siriuscanada.com
(Canada).
Registering satellite radio X
Select Audio in the main function bar by
sliding 002A001Cand turning 0031001C0032the COMAND
controller and press 0021to confirm.
X Select Sat. Radio and press
0021to
confirm. Service information screen
1
Provider's phone number (SIRIUS XM)
2 SIRIUS XM ID of your satellite receiver
X Call the phone number of your satellite
radio provider shown on the screen.
i You can also have the satellite service
activated online. To do so, visit the SIRIUS
XM Radio website at
http://www.sirius.com (USA) or Audio
221COMAND Z

Changing the front bulbs
High-bea mspot lamp (vehicles with
halogen daytime running lamps) X
Switch off the lights.
X Ope nthe hood.
X Turn housing cover 0002counter-clockwise
and pull it out.
X Turn bulb holder 0003counter-clockwise and
pull it out.
X Take the bulb out of bulb holder 0003.
X Insert the new bulb into bulb holder 0003.
X Insert bulb holder 0003.
Left-hand headlamp: cable outlet 0026must
be pointing up and to the right.
Right-hand headlamp: cable outlet 0026must
be pointing down and to the left.
X Turn bulb holder 0003clockwise.
Handle 0025of bulb holder 0003is horizontal.
X Align housing cover 0002and turn it
clockwise until it engages. High-beam spot lamp (vehicles with
LED-daytime running lamps)/infrared
light (Night View Assist Plus) Due to their location, have the bulbs in the
left-hand headlamp changed at a qualified
specialist workshop.
X Switch off the lights.
X Open the hood.
X Turn housing cover 0002counterclockwise
and pull it out.
X Turn bulb holder 0003counterclockwise and
pull it out.
X Push the two detents on the right and left
of bulb holder 0003and pull the bulb from
bulb holder 0003.
X Insert the new bulb into bulb holder 0003until
it engages.
X Insert bulb holder 0003into the guide in the
headlamp.
Cable outlet 0026must be pointing down and
to the right.
X Turn bulb holder 0003clockwise.
Cable outlet 0026must be pointing down and
to the left.
X Align housing cover 0002and turn it
clockwise until it engages. 288
Replacing bulbsLights and windshield wipers

0025
Cente rvent thumbwheel, left
0023 Center air vent, left
X To open/close: turn thumbwheels 0026
and 0025up or down. Setting the side air vents
X
To open/close: turn thumbwheel 0026up or
down.
i Side window defroster vent 0002is never
completely shut, even if side air vent 0003is
shut. Setting the glove box air vent
When automatic climate control is activated,
the glove box can be ventilated, for instance
to cool its contents. The level of airflow
depends on the airflow and air distribution
settings.
! Close the air vent when heating the
vehicle.
At high outside temperatures, open the air
vent and activate the "cooling with air
dehumidification" function .Otherwise,
temperature-sensitive items stored in the
glove bo xcould be damaged. X
To open: turn thumbwheel 0002counter-
clockwise from position 0007to position 0006.
X To close: turn thumbwheel 0002clockwise
from position 0006to position 0007. Setting the rear-compartment air
vents
Setting the center vents in the rear
compartment 0002
Rear-compartment air vent, left
0003 Rear-compartment air vent, right
0026 Rear-compartment air vent thumbwheel,
right
0025 Rear control panel for automatic climate
control
0023 Rear-compartment air vent thumbwheel,
left
X To open/close: turn thumbwheel 0026or
0023 to the right or left.
i In vehicles without rear-compartmen tair-
conditioning system: close the rear- Setting the air vents
303Climate control Z

pump nozzle, which could cause personal
injury. G
WARNING
Hybrid vehicles: be sure to read the "HYBRID"
supplement .Otherwise, you could fail to
recognize dangers. G
WARNING
Do not fill diesel tanks with gasoline .Do not
mix diesel fuel with gasoline. Otherwise the
fuel system and engine could be damaged. In
addition, the vehicle could catch fire.
! Do not use gasoline to refuel vehicles with
a diesel engine. Do not use diesel to refuel
vehicles with a gasoline engine. Even a
small quantity of the wrong fuel will
damage the fuel system and engine.
! Do not switch on the ignition if you
accidentally refuel with the wrong fuel.
Otherwise, the fuel will enter the fuel lines.
Notify a qualified specialist workshop and
have the fuel tank and fuel lines drained
completely.
! Overfilling the fuel tank could damage the
fuel system.
! Take care not to spill any fuel on painted
surfaces. You could otherwise damage the
paintwork.
! Use a filter when refueling from a fuel can.
Otherwise, the fuel lines and/or injection
system could be blocked by particles from
the fuel can.
Further information on fuel and on fuel grades
can be found in the "Fuel" section
(Y page 531). Refueling
Fuel filler flap 0002
To open the fuel filler flap
0003 To insert the fuel filler cap
0026 Tire pressure table
0025 Fuel type
The fuel filler flap is unlocked or locked
automatically when you open or close the
vehicle with the SmartKey or with KEYLESS-
GO.
The position of the fuel filler cap 000Fis
displayed in the instrument cluster. The arrow
next to the filling pump indicates the side of
the vehicle.
Opening X
Switch off the engine.
X Remove the SmartKey from the ignition
lock.
X KEYLESS-GO: open the driver’s door.
This corresponds to SmartKey position 0:
"SmartKey removed".
The driver’s door can be closed again.
X Press the fuel filler flap in the direction of
arrow 0002.
The fuel filler flap opens slightly.
X Open the fuel filler flap fully.
X Turn the fuel filler flap counter-clockwise
and remove it.
X Insert the fuel filler cap into the holder
bracket on the inside of filler flap 0003.322
RefuelingDriving and parking