sensor MERCEDES-BENZ S-CLASS COUPE 2018 Owner's Guide

turn signal indicatorre mains on, all other de tec‐
te dve hicles are indicated only bytheflashing of
th ere dwa rning lamp.
If yo uove rtake a vehicle quickl y,no warning is
given.
& WARNING Risk of accident despite Blind
Spot Assist
Blind Spot Assist does notreact tovehicles
approaching and overtaking you at a greatly
di fferent speed.
As a result, Blind Spot Assist cannot warn
drivers in this situation.
#Alw ays pay careful attention tothe traf‐
fi c situation and maintain a safe dis‐
ta nce at the side of theve hicle.
Blind Spot Assist and Active Blind Spot Assi st
are only aids. They may failto detect some vehi‐
cles and are no substitute for attentive driving.
Alw ays ensure that there is suf ficient dist anceto
th e side forot her road users and obs tacles. Sy
stem limitations
The sy stem may be limited in thefo llowing situa‐
tions:
Rth e sensors are dirty or co vered
Rpoor visibility, e.g. due tofog, heavy rain,
snow or spr ay
Rnarrow vehicles, e.g. bicycles, are within the
monitoring range
Wa rnings may be issued in er ror when driving
close tocrash barr iers or similar solid lane bor‐
ders. Warnings may be inter rupte d when driving
alongside long vehicles, e.g. truc ks,fo r a pro‐
longed time.
Blind Spot Assist is not operational when reve rse
ge ar is engaged.
Fu nction of brake application (Active Blind
Spot Assist)
If Ac tive Blind Spot Assi stdetects a risk of a side
impact in the monitoring range, a cours e-cor‐
re cting brake application is car ried out. This is
designed tohelp youav oid a collision. The course-cor
recting brake application is availa‐
ble in the speed range between appr oximately
20 mph (30 km/h) and 125mp h (200 km/h).
&
WARNING Risk of accident despite
brake application of Active Blind Spot
Assi st
A cours e-correcting brake application cannot
alw ays pr event a collision.
#Alw aysst eer, brake or accelera teyour‐
self, especially if Active Blind Spot
Assi stwa rnsyo u or makes a course-
co rrecting brake application.
#Alw ays maintain a safe dis tance at the
sides.
& WARNING Risk of accident despite
Ac tive Blind Spot Assi st
Ac tive Blind Spot Assi stdoes not react tothe
fo llowing:
ROver taking vehicles closely on the side,
placing them in the blind spot area.
Driving and parking 19
9

System limitations
No lane-cor recting brake application occurs in
th efo llowing situations:
RYo u clear lyand actively steer, brake or accel‐
erate.
RYo u ha veswitched on the turn signal indica‐
to r.
RA driving safe ty system inter venes, such as
ESP®, Ac tive Brake Assi stor Active Blind
Spot Assi st.
RYo u ha veadop ted a sporty driving style with
high cornering speeds or high rates of accel‐
eration.
RESP®is deactivated.
RIf a loss of tire pressure or a defective tire
has been de tected and displ ayed.
The sy stem may be impaired or may not function
in thefo llowing situations:
RIf th ere is poor visibility, e.g. due toinsuf fi‐
cient illumination of thero ad, highly variable
shade conditions, or due torain, sno w,fog or
heavy spr ay.
RThere is glare, e.g. from oncoming traf fic, the
sun or reflections.
RIf th ere is dirt on the windshield in the vicin‐
ity of the multifunction camera or the camera
is mis ted up, damaged or obscured.
RNo or se veral, unclear lane markings are
present for one lane, e.g. near roadwor ks.
RThe lane markings are worn, dark or co vered.
RThe dis tance totheve hicle in front is too
small and the lane markings thus cannot be
de tected.
RThe lane markings change quickl y,e.g. lanes
branch off, cross one ano ther or mer ge.
RThe roadw ayisvery nar row and winding.
Ve hicles with Driving Assistance pac kage or
Driving Assistance Plus pa ckage: Active Lane
Ke eping Assist uses radar sensors tomonitor
se veral areas around theve hicle. If thera dar
sensors in there ar bumper are dirty or co vered
with snow ,th e sy stem may be impaired or may
not function. If an obs tacle in the lane in which
yo u are driving has been de tected, no lane-cor‐
re cting brake application occurs .Ac
tivating Active Lane Keeping Assist
&
WARNING Risk of accident despite
Ac tive Lane Keeping Assist warning
A lane-cor recting brake application cannot
al wa ys bring theve hicle back into the origi‐
nal lane.
#Alw aysst eer, brake or accelera teyour‐
self, especially if Active Lane Keeping
Assist warnsyo u or makes a lane-cor‐
re cting brake application.
&
WARNING Risk of accident despite inter‐
ve ntion of Active Lane Keeping Assist
Ac tive Lane Keeping Assist does not de tect
traf fic conditions or road users. In very rare
cases, the sy stem may make an inappropri‐
ate brake application, e.g. af ter intentional ly
driving over a solid lane marking.
The brake application can be inter rupte d at
any time if yousteer slightly in the opposite
direction.
202 Driving and parking

#If a destination isreceived: selectYesand
continue with me thod 1 or 2.
or
#If a destination wasre ceive d with pho to
information, select Start Route Guidance .
Ro ute guidance starts.
#Me thod 1: if route guidance isnot act ive,
select Start Route Guidance .
The route tothe destination is calculated.
The map sho ws thero ute. Route guidance
th en begins.
#Me thod 2: if route guidance isact ive, select
St art New Route Guidance orSet as Next
Way Point .
St art New Route Guidance :th ere ceive d des‐
tination address is set as a new destination.
The pr evious destinations and intermediate
destinations are dele ted. Ro ute guidance to
th e new destination begins.
Set as Next Way Point :th ere ceive d destina‐
tion address is set as the next new inter‐
mediate destination. Route guidance begins.
Ro ute guidance with cur rent traf fic re ports
Traf fic information overview
Tr af fic re ports are receive d using Live Traf fic
Information and are used forro ute guidance.
This service isuna vailable in some countries.
There may be dif fere nces between the traf fic
re ports receive d and the actual road and traf fic
conditions.
Impor tant information on Live Traf fic Informa‐
tion:
RCu rrent tra ffic reports are receive d via the
Internet connection.
RThe traf fic situation is update d at short,regu‐
lar inter vals.
RThe subscri ption information sho ws thest a‐
tus (→page 268).
Info rmation on theve hicle's position is regular ly
sent toDaimler AG. The da tais immediately ren‐
de red anonymous byDaimler AGand forw arded
to the tra ffic data pr ovider. Using this data, traf‐
fi c re ports releva nt totheve hicle's position are
sent totheve hicle. The vehicle acts as a sensor fo
rth eflow of traf fic and helps toimpr ovethe
qu ality of the tra ffic reports.
If yo udo not wish totransmit your vehicle posi‐
tion, you can ha vethis service deactivated at an
authorized Mercedes-Benz Center.
Displaying subscription information
Re quirements:
RThe vehicle is equipped with Live Traf fic
Information.
Multimedia sy stem:
,Navigation.Z Options
The subscription expiry date is automatically dis‐
pla yed:
Rone month before theex piry date
Rone week before theex piry date
Ron theex piry date
268
Multimedia sy stem

Engine oil
Checkingthe engine oil le vel with an on-
board computer
The engine oil le vel is de term ined during driving.
The oil le vel display is only available af ter a driv‐
ing time of up to30 minutes and if the ignition is
switched on, depending on the driving profile.
It is not possible tocor rectly measure the oil
le ve l if:
Rtheve hicle is not le vel during the measure‐
ment process.
Rth e hood was pr eviously opened.
The engine must be restar ted and the engine oil
le ve l will be de term ined again when driving.
On-board computer:
,Service.Engine Oil Level
Yo u will see one of thefo llowing messa ges in
th e multifunction displa y:
#Measuring Engine Oil Level...: measurement
ofthe oil le vel is not yet possible. Repeat the
requ est af ter a maximum of 30 minutes' driv‐
ing.
#Engine Oil Level OK andthe bar display for
indicating the oil le vel in the multifunction
display is green and is between "min" and
"max": the oil le vel is cor rect.
#Engine Oil Level Add 1.0 l andthe bar display
fo r indicating the oil le vel in the multifunction
display is orange and is below "min": top up
with 1.1 US qt (1 l) of engine oil.
#Reduce Engine Oil Level andthe bar display
fo r indicating the oil le vel in the multifunction
display is orange and is abo ve"max ":drain
off theex cess engine oil. Consult a qualified
specialist workshop.
#For Engine Oil Level Switch Ignition On:
switch on the ignition tocheck the engine oil
le ve l.
#Engine Oil Level System Inoperative: sensor
defective or not connec ted. Consult a quali‐
fi ed specialist workshop.
#Engine Oil Level System Currently Unavail.:
close the hood. Ad
ding engine oil
&
WARNING Risk of burn s from hot com‐
ponent parts in the engine compartment
Cer tain component parts in the engine com‐
partment can be very hot, e.g. the engine,
th e cooler and parts of theex haust sy stem.
#Let the engine cool down and only
to uch the component parts described
as follo ws .
&
WARNING Risk offire and injury from
engine oil
If engine oil comes into con tact wi thhot
component parts in the engine compart‐
ment, it may ignite.
#Make sure that no engine oil is spilled
next tothefiller opening.
#Allow the engine tocool off and thor‐
oughly clean the engine oil from compo‐
nent parts before starting theve hicle.
Maintenance and care 327

Observethefo llowing information:
Information on cleaning and car eAvoiding vehicle damage
Wheels/rims Usewate r and acid-free wheel cleaners.
RDo not use acidic wheel cleaners toremo vebrake dust.
This could damage wheel bolts and brake components.
RTo avoid cor rosion of the brake discs and brake pads,
drive theve hicle for a few minutes af ter cleaning before
parking it. The brake discs and brake pads warm up and
dr y out.
Wi ndo ws
Cleanthe windo wsonthe inside and outside using a damp
clo thand cleaning agents recommended byMercedes-Benz. Do not use dry clo
ths or abrasive or sol vent-based cleaning
agents toclean the inside of windo ws.
Wi per blades
Fold out the wiper blades and clean them using a damp clo th.D o not clean the wiper blades too of ten.
Ex terior lighting
Cleanthe lenses with a wet sponge and mild cleaning agent,
e.g. car sha mpoo. Only use cleaning agents or cleaning clo
thsth at are suitable
fo r plast ic lenses.
Sensors Cleanthe sensors in the front and rear bumper and in the
ra diator trim with a soft clo thand car shampoo. When using a high-pressure
water jet, maintain a minimum
dis tance of 11.8 in (30 cm).
Maintenance and care 337

The system checks the tire pressure and the tire
te mp erature of the tires ins talled on theve hicle
by means of a tire pressure sensor.
New tire pressure sensors, e.g. in winter tires,
are automatically taught-in during thefirs t jour‐
ney they are used.
If th ere is a subs tantial pressure loss or if the
tire temp erature is excessive, a warning will be
given:
Rvia display messages (→page 429)
Rvia theh warning lamp in the instrument
clus ter (→page 462)
It is the driver's responsibility toset the tire
pressure tothere commended cold tire pressure
suitable forth e operating situation. Set the tire
pressure for cold tires using a tire pressure
ga uge. Notethat the cor rect tire pressure forth e
cur rent operating situation must firs t be taught-
in to the tire pressure monitoring sy stem.
In most cases, the tire pressure monitoring sys‐
te m will auto matically update the new refere nce
va lues af teryo u ha vechanged the tire pressure.
Yo u can, ho wever,also update there fere nce val‐ ues
byrestarting the tire pressure monitoring
sy stem manually (
→page 368).
Sy stem limitations
The sy stem may be impaired or may n
ot function
in thefo llowing situations:
RIf th e tire pressure is set incor rectly
RIfth ere is a sudden pressure loss caused, for
ex ample, byafo re ign object penetrating the
tire.
RIf th ere is a malfunction caused byano ther
ra dio signal source
Make sure toobser vethefo llowing fur ther rela‐
te d subjec t:
RNotes on tire pressure (→page 363)
Checking the tire pressure with the tire pres‐
sure moni toring sy stem
Requ irements:
RThe ignition is switched on. On-board computer:
,Service.Tires
One of thefo llowing displa ysappears:
RCur rent tire pressure of ea chwheel:
RTire pressure will be displayed after driving a
few minutes
RTire Pressure Monitor Active: thete ach-in
process of the sy stem is not yet comple te.
The tire pressures are already being moni‐
to re d.
#Compare the tire pressure with there com‐
mended tire pressure forth e cur rent operat‐
ing status (
→page 364). Observ eth e no tes
on tire temp erature (→page 363).
% The values displa yed in the multifunction dis‐
play may deviate from those of the tire pres‐
sure gauge as they referto sea le vel.At high
altitudes, the tire pressure values indicated
by pressure gauges are higher than those
shown bythe on-board computer. In this
case, do not reduce the tire pressure.
Wheels and tires 367

Observethefo llowing when selecting, ins talling
and replacing tires:
ROnly use tires and wheels of the same type
(summer tires, winter tires, MOEx tended
tires) and the same make.
ROnly ins tall wheels of the same size on one
axle (left and right).
It is only permissible toins tall a dif fere nt
wheel size in theeve nt of a flat tire in order
to drive tothe specialist workshop.
ROnly ins tall tires of the cor rect size onto the
wheels.
RVe hicles with a tire pressure monitoring
sy stem: all mounte d wheels must be equip‐
ped with functioning sensors forth e tire
pressure monitoring sy stem.
RAt temp eratures below 45 °F (7 °C), use win‐
te r tires or all-season tires mar ked M+S for
all wheels.
Wi nter tires bearing thei snowflake sym‐
bol in addition tothe M+S marking pr ovide
th e best possible grip in wintry road condi‐
tions.
RFo r M+S tires, only use tires with the same
tread.
RObser vethe maximum permissible speed for
th e M+S tires ins talled.
If th is is below theve hicle's maximum speed,
th is must be indicated in an appropriate label
in the driver's field of vision.
RRu n in new tires at moderate speeds forth e
fi rs t 60 miles (100 km).
RRe place the tires af ter six years at the latest,
re ga rdless of wear.
RWhen replacing with tires that do not fea‐
ture run-flat characteristics: vehicles with
MOExtended tires are not equipped with a
TIREFIT kit at thefa ctor y.Equip theve hicle
with a TIREFIT kit af terre placing with tires
th at do not feature run-flat characteristics,
e.g. winter tires.
Fo r more information on wheels and tires, con‐
ta ct a qualified specialist workshop.
Be sure toalso observ eth efo llowing fur ther
re lated subjects:
RNo tes on tire pressure (→page 363)
RTire and Loading Info rmation placard
(→page 369)
RTi re size designation, load-beari ng capacity,
speed rating and load ind ex(→page 376)
RTire pressure table (→page 364)
Note s onrotating wheels
&
WARNING Risk of injury thro ugh dif fer‐
ent wheel sizes
Inter changing the front and rear wheels if the
wheels or tires ha vediffere nt dimensions
may se verely impair the driving characteris‐
tics.
The wheel brakes or wheel suspension com‐
ponents may also be damaged.
#Ro tate front and rear wheels only ifth e
wheels and tires are of the same dimen‐
sions.
Wheels and tires 383

&WARNING ‑ Risk of fire and injury from
windshield washer concentrate
Wi ndshield washer concentrate is highly
fl ammable. It could ignite if it comes into
con tact wi thhot engine component parts or
th eex haust sy stem.
#Make sure that no windshield washer
concentrate spills out next tothefiller
opening.
* NO
TEBlocked spr aynozzles caused by
mixing windshield washer fluids
#Do not mix MB SummerFit and MB Win‐
te rFit with other windshield washer flu‐
ids.
Do not use distilled or de-ionized water asthefill
le ve l sensor may be triggered er roneously.
Re commended windshield washer fluid:
RAbo vefreezing point: e.g. MB SummerFit
RBelow freezing point: e.g. MB WinterFit Fo
rth e cor rect mixing ratio referto the informa‐
tion on the antif reeze conta iner.
Mix thewa sher fluid withth e windshield washer
fl uid all year round.
Re frigerant
Note s onrefrigerants
Obser vethe no tes on operating fluids
(
→page 395).
* NO
TEDama gedue toincor rect refriger‐
ant
If a non-appr ovedre frigerant is used, the cli‐
mate control sy stem may be damaged.
#Only use there frigerant R‑134a
* NO
TEDama getothe climate control
sy stem due toincor rect refrigerant com‐
pressor oil
#Only use refrigerant compressor oil that
has been appr ovedby Mercedes-Benz.
#Do not mix the appr ovedre frigerant
compressor oil with a dif fere nt refriger‐
ant compressor oil.
Wo rkon the climate control sy stem may only be
car ried out byaqu alified specialist workshop. All
applicable regulations, as well as SAEstandard
J639, must be adhered to.
1Wa rning symbols
2Re frigerant filling capacity
3Applicable standards
4PA G oil part number
5Re frigerant type
400
Tech nical da ta

Displaymessages
Possible causes/consequences and MSolutions
Radar Sensors Dirty See
Operator's Manual *T
heradar sensor sy stem is malfunctioning. Possible causes are:
Rsoiling of the sensors
Rheavy rain
Rex tended country driving wi thout other traf fic, e.g. in the desert
Driving sy stems and driving saf etysy stems may be malfunctioning or temp orarily una vailable.
Once the cause of the problem is no longer present, the driving sy stems and driving saf etysy stems will be available
again.
If th e display message does not disappear:
#Pull over and stop theve hicle safely as soon as possible, paying attention toroad and traf fic conditions.
#Clean all sensors .
#Restart the engine.
Display messages and warning/indicator lamps 41
5

Displaymessages
Possible causes/consequences and MSolutions
Active Blind Spot Assist
Currently Unavailable See
Operator's Manual *A
ctive Blind Spot Assist istemp orarily una vailable.
The sy stem limitations ha vebeen reached (
→page 198) (→page 199) (→pag e19 8).
#Drive on.
Once the cause of the problem is no longer present, the sy stem will be available again.
#Ifth e display message does not disappear, stop theve hicle while paying attention toroad and traf fic conditions
and restart the engine.
Active Blind Spot Assist
Inoperative *A
ctive Blind Spot Assist is malfunctioning.
#Visit a qualified specialist workshop.
Blind Spot Assist Currently
Unavailable See Operator's
Manual *B
lind Spot Assist is temp orarily una vailable.
The sy stem limitations ha vebeen reached (
→page 198) (→page 199) (→pag e19 8).
#Drive on.
Once the cause of the problem is no longer present, the sy stem will be available again.
or
#If th e display message does not disappear, stop theve hicle while paying attention toroad and traf fic conditions
and restart the engine.
#If necessar y,clean there ar bumper. If the bumper is extreme lydirty, the sensors in the bumper may be mal‐
functioning.
Blind Spot Assist Inopera-
tive *B
lind Spot Assist is malfunctioning.
#Visit a qualified specialist workshop.
422
Display messages and warning/indicator lamps