remote control MERCEDES-BENZ SL600 2008 R230 User Guide

257 Controls in detail
Useful features
The Response Center will then unlock your
vehicle with the remote door unlocking
feature.Stolen Vehicle Recovery services
In the event your vehicle was stolen:
Report the incident to the police.
The police will issue a numbered
incident report.
Pass this number on to the
Mercedes-Benz Response Center along
with your password issued to you when
you subscribed to the service.
The Response Center will then attempt
to covertly contact the vehicle’s Tele
Aid system. Once the vehicle is locat-
ed, the Response Center will contact
the local law enforcement and you. The
vehicle’s location will only be provided
to law enforcement.
Garage door opener
The integrated remote control is capable of
operating up to three separately controlled
devices. It provides a convenient way to
replace up to three hand-held remote
controls used to operate devices such as
garage door openers, gate openers, or
other devices compatible with HomeLink
®
or some other systems.
Before the integrated remote control can
be used, it must be programmed to the
garage door opener, gate operator or other
device you wish to operate. See the
following instructions for programming
information.
iThe remote door unlock feature is available
if the relevant cellular phone network is avail-
able.
The SOS button will flash and the message
Call
Connected
will appear in the multifunction dis-
play to indicate receipt of the door unlock com-
mand.
Once the vehicle is unlocked, a Response Center
specialist will attempt to establish voice contact
with the vehicle occupants.
If the trunk recessed handle was pulled for more
than 20 seconds before door unlock authoriza-
tion was received by the Response Center, you
must wait 15 minutes before pulling the trunk re-
cessed handle again.
iIf the anti-theft alarm or the tow-away alarm
stays on for more than 30 seconds, a call to the
Response Center is initiated automatically by the
Tele Aid system provided Tele Aid service was
subscribed to and properly activated, and that
necessary cellular service and GPS coverage are
available. See anti-theft alarm system
(
page 98) and tow away alarm (page 100).

258 Controls in detail
Useful features
Interior rear view mirror with integrated
remote control
1Indicator lamp
2 3 4Signal transmitter button
Needed for programming (not part of
vehicle equipment):
5Hand-held remote control of
garage door opener, gate
operator or other device
6Hand-held remote control
buttonProgramming the integrated remote
control
Step 1:
Switch on the ignition (page 40).
Warning!G
Before programming the integrated remote
control to a garage door opener or gate
operator, make sure people and objects are
out of the way of the device to prevent po-
tential harm or damage. When programming
a garage door opener, the door moves up or
down. When programming a gate operator,
the gate opens or closes.
Do not use the integrated remote control
with any garage door opener that lacks
safety stop and reverse features as required
by U.S. federal safety standards (this
includes any garage door opener model
manufactured before April 1, 1982).
A garage door that cannot detect an object
– signaling the door to stop and reverse –
does not meet current U.S. federal safety
standards.
When programming a garage door opener,
park the vehicle outside the garage.
Do not run the engine while programming
the integrated remote control.
Inhalation of exhaust gas is hazardous to
your health. All exhaust gas contains carbon
monoxide (CO), and inhaling it can cause un-
consciousness and possible death.

259 Controls in detail
Useful features
Step 2:
If you have previously programmed an
signal transmitter button and wish to
retain its programming, proceed to
step 3.
If you are programming the integrated
remote control for the first time, press
and hold the two outer signal transmit-
ter buttons2 and4 and release
them only when indicator lamp1
begins to flash after approximately
20 seconds (do not hold the button for
longer than 30 seconds). This proce-
dure erases any previous settings for
all three channels and initializes the
memory.
If you later wish to program a second
and/or third hand-held transmitter to
the remaining two signal transmitter
buttons, do not repeat this step and be-
gin directly with step 3.Step 3:Hold the end of hand-held remote
control5 of the device you wish to
train approximately 2 to 5 in
(5 to12 cm) away from the signal trans-
mitter button (2, 3 or4) to be pro-
grammed, while keeping indicator
lamp1 in view.
Step 4:
Using both hands, simultaneously
press hand-held remote control
button6 and the desired signal trans-
mitter button (2, 3 or4). Do not
release the buttons until step 5 is com-
pleted.
Indicator lamp1 will flash, first slowly
and then rapidly.Step 5:
After indicator lamp1 changes from a
slow to a rapidly flashing light, release
the hand-held remote control button
and the signal transmitter button.
Step 6:
Press and hold the just-trained signal
transmitter button (2, 3 or4) and
observe indicator lamp1.
If indicator lamp1 stays on
constantly, programming is complete
and your device should activate when
the respective signal transmitter
button (2, 3 or4) is pressed and re-
leased.
iIndicator lamp1 flashes immediately the
first time the signal transmitter button is pro-
grammed. If this button has already been pro-
grammed, the indicator lamp will only start
flashing after 20 seconds.
iIf indicator lamp1 flashes rapidly for about
2 seconds and then turns to a constant light,
continue with programming steps 8 through 12
as your garage door opener may be equipped
with the “rolling code” feature.

261 Controls in detail
Useful features
Gate operator/Canadian programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission
which may not be long enough for the
integrated signal transmitter to pick up the
signal during programming. Similar to this
Canadian law, some U.S. gate operators
are designed to “time-out” in the same
manner.
If you live in Canada or if you are having
difficulties programming a gate operator
(regardless of where you live) by using the
programming procedures, replace step 4
with the following:
Step 4:
Press and hold the signal transmitter
button (2, 3 or4). Do not release
this button until it has been success-
fully trained.
While still holding down the signal
transmitter button (2, 3 or4),
“cycle” your hand-held remote control
button6 as follows: Press and hold
button6 for 2 seconds, then release
it for 2 seconds, and again press and
hold it for 2 seconds. Repeat this se-
quence on the hand-held remote con-
trol until the frequency signal has been
learned. Upon successful training, indi-
cator lamp1 will flash slowly and then
rapidly after several seconds.
Proceed with programming step 5 and
step 6 to complete.Reprogramming a single signal trans-
mitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:
Switch on the ignition (page 40).
Press and hold the desired signal
transmitter button (2, 3 or4).
Do not release the button.
Indicator lamp1 will begin to flash af-
ter 20 seconds. Without releasing the
signal transmitter button, proceed with
programming starting with step 3.
iUpon completion of programming the inte-
grated remote control, make sure you retain the
hand-held remote control that came with the ga-
rage door opener, gate operator or other device.
You may need it for use in other vehicles, for fu-
ture programming of an integrated remote con-
trol, or simply for continued use as a hand-held
remote control to operate the respective device
in other situations.

262 Controls in detail
Useful features
Operation of integrated remote control
Switch on the ignition (page 40).
Select and press the appropriate inte-
grated signal transmitter button (2,
3 or4) to activate the remote con-
trolled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.
Erasing the integrated remote control
memory
Switch on the ignition (page 40).
Simultaneously press and hold outer
signal transmitter buttons2 and 4,
for approximately 20 seconds, until the
indicator lamp1 flashes rapidly. Do
not hold for longer than 30 seconds.
The codes of all three channels are
erased.Programming tips
If you are having difficulty programming
the integrated remote control, here are
some helpful tips:

Check the frequency of hand-held re-
mote control5 (typically located on
the reverse side of the remote). The in-
tegrated remote control is compatible
with radio-frequency devices operating
between 280-390 MHz.

Put a new battery in hand-held remote
control5. This will increase the likeli-
hood of the hand-held remote control
sending a faster and more accurate sig-
nal to the integrated remote control.

While performing step 3, hold
hand-held remote control5 at
different lengths and angles from the
signal transmitter button (2, 3 or4)
you are programming. Attempt varying
angles at the distance of
2 to 5 in (5 to 12 cm) away or the
same angle at varying distances.

If another hand-held remote control is
available for the same device, try the
programming steps again using that
other hand-held remote control. Make
sure new batteries are in the hand-held
remote control before beginning the
procedure.

Straighten the antenna wire from the
garage door opener assembly. This
may help improve transmitting and/or
receiving signals.
iIf you sell your vehicle, erase the codes of all
three channels.
iCertain types of garage door openers are in-
compatible with the integrated remote control. If
you should experience further difficulties with
programming the integrated remote control,
contact an authorized Mercedes-Benz Center, or
call Mercedes-Benz Customer Assistance
Center (in the USA only) at
1-800-FOR-MERCedes, or Customer Service (in
Canada) at 1-800-387-0100.

380 Practical hints
What to do if …
Left displayRight displayPossible cause/consequencePossible solution
2 Brake WearThe brake pads have reached their
wear limit.Have the brake pads replaced as soon as pos-
sible.
Warning!G
Have brake pad replacement and other work
on the electro-hydraulic brake system
carried out by qualified technicians only.
Contact an authorized Mercedes-Benz
Center for further information.
The electro-hydraulic brake system must be
deactivated prior to working on the system.
High pressure is intermittently built up in the
system as part of its automatic self-test.
In addition, the system is automatically
activated when the vehicle is unlocked by
remote control, when the driver or passen-
ger door is opened, when the SmartKey in
the starter switch is turned to position1 or
the KEYLESS-GO* start/stop button is
pressed once, when the brake pedal
is depressed or when the parking brake is
released. Failure to deactivate the system
prior to maintenance will cause brake pis-
tons to extend and brake fluid to leak, which
may result in injuries (contusions and acid
burns). Extended brake pistons may also
cause injury.!Brake pad thickness must be visually
checked by a qualified technician at the intervals
specified in the Maintenance Booklet.

472 Index
Emergency operations
Glove box, Unlocking 404
Load assist, Lowering 406
Locking/unlocking the
vehicle 403, 405
Remote door unlock, Tele Aid 256
Trunk lid, Releasing from the
inside 121
Trunk lid, Unlocking 404
Emergency Tensioning Device see ETD
Emission control 277
Information label 445
System warranties 10
Engine
Block heater (Canada only) 328
Break-in recommendations 266
Cleaning 335
Compartment 282
Malfunction indicator lamp 29, 346
Number 445
Poly-V-belt layout 446
Starting 53
Tachometer 29
Technical data 447
Turning off 64Engine coolant see Coolant
Engine oil 283, 460
Adding 286, 457
Additives 460
Checking level, With control
system* 284
Checking level, With oil dipstick 286
Consumption 283
Filler cap 287
Filler neck 286, 287
Messages in the multifunction
display 285, 388
Oil dipstick 286
ESP
®89, 91
Switch 32
Switching off 93
Switching on 94
Synchronizing 367
Warning lamp 27, 342
ETD 82
Safety guidelines 72
Warning and indictor lamps 354
Exterior lamp switch 131
Exterior rear view mirrors 49, 185F
Filler cap, Engine oil 287
Filler neck, Engine oil 286, 287
First aid kit 400
Flat tire 417
Mounting the spare wheel 417
Preparing the vehicle 417
Spare wheel 400
Floormat* 247
Fluids
Automatic climate control
system 457
Automatic transmission 287, 457
Brake system 281, 457, 460
Capacities 457
Engine coolant 288, 457, 463
Engine oil 283, 457, 460
Power steering 457
Retractable hardtop, Hydraulics 457
Windshield washer and headlamp
cleaning system 457
Fog lamps 134
Messages in the multifunction
display 393, 394
Replacing bulbs 410

474 Index
High-performance brake system
(AMG vehicles only) 270
Hood 282
Messages in the multifunction
display 390
Opening 282
Horn 25
HVAC see Automatic climate control
Hydroplaning 272
I
Identification labels 444
Identification number, Vehicle (VIN) 445
Ignition 40
Immobilizer 98
Indicator lamps see Lamps, indicator and
warning
Infant and child restraint systems see
Children in the vehicle
Inflation pressure see Tire inflation
pressure
Inside door handle 113Instrument cluster 26, 140
Illumination brightness 140
Lamps 342
Language 160
Messages in the multifunction
display 26, 359
Multifunction display 143
Instrument lighting see Instrument cluster,
Illumination brightness
Instrument panel see Instrument cluster
Instruments and controls see Cockpit
Interior lighting 138
Delayed switch-off 165
Interior rear view mirror 49
Antiglare position 185
Auto-dimming 185
J
Jack 401
Jacking up the vehicle 418
Jump starting 432K
Key, Mechanical 403
Valet locking 120
Key, SmartKey
Batteries 407
Battery check lamp 104
Checking the batteries 113
Factory setting 106
Global locking 106, 107
Global unlocking 106, 107
Locking/unlocking 38, 65, 104
Loss of 113
Messages in the multifunction
display 390
Opening, Trunk 115
Opening/closing retractable
hardtop 206
Remote control 104
Replacing batteries 407
Reprogramming 107
Restoring to factory settings 107
Selective setting 107
Starter switch positions 40
Starting the engine 53
Turning off the engine 64
Unlocking, Trunk lid 114

475 Index
Key, SmartKey with KEYLESS-GO* 108
Batteries 407
Battery check lamp 108
Checking the batteries 113
Factory setting 111
Global locking 111, 112
Global unlocking 111, 112
Locking/unlocking 39, 65, 108
Loss of 113
Messages in the multifunction
display 390, 391
Opening, Trunk 115
Opening/closing retractable
hardtop 206
Remote control 108
Replacing batteries 407
Reprogramming 112
Restoring to factory settings 112
Selective setting 112
Starter switch positions 41
Starting the engine 54
Turning off the engine 64
Unlocking, Trunk lid 114KEYLESS-GO*
Closing windows 203
Important notes 109
Locking/unlocking 39, 65, 108
Messages in the multifunction
display 390
Start/stop button 31, 41, 54
Starter switch positions 41
Starting the engine 54
Turning off the engine 64
Unlocking, Trunk lid 114
Kickdown 175
Kilopascal 323
Knee bag 74
L
Labels, identification 444
Lamp bulbs, exterior 409
Lamps, exterior
Delayed switch-off 164
Exterior lamp switch 25, 57
Front 410
Light sensor 392
Replacing bulbs for rear 410, 414
Switching off 131
Switching on 131Lamps, indicator and warning
ABS 29, 344
ABS/ESP
®342
Brakes 345
CHECK ENGINE 346, 347
Coolant 348
Distronic* indicator and warning
lamp 27, 221
Electro-hydraulic brake system 94
Engine diagnostics 346, 347
Engine malfunction 29
ESP
®91
Fuel reserve 350
Passenger front air
bag off 74, 78, 357
Seat belt telltale 352
Seat belts 352–353
SRS 69, 354
Turn signals 27
Language
Multifunction display 160
Leather upholstery
Cleaning 340
License plate lamps 163, 410, 414
Light alloy wheels, cleaning 338

479 Index
Power windows 201
Cleaning 337
Closing with KEYLESS-GO* 203
Side windows 201
Synchronizing 203
Problems while driving 60
Production options weight 324
Program mode see Automatic transmis-
sion, Automatic shift program
Program mode selector switch
Automatic shift program 177
Automatic transmission 32
PSI 324
PULSE function (Massage function) 125
Q
Quick search
Phone book* 171R
RACETIMER see Control system menus,
AMG
Radio
Operating 154
Satellite 154
Selecting station 154
Radio transmitters
Control and operation 276
Range (distance to empty)
Calling up 169
Reading lamp 33
Rear lamps see Tail lamps
Rear luggage compartment 242
Rear view mirrors see Mirrors
Recommended inflation pressure 324
Redial memory 171
Refueling 279
Regular checks 280
Regular driving style 233
Remote trunk opening switch 116
Remote trunk opening/closing*
switch 116Replacing
Batteries (SmartKey with
KEYLESS-GO*) 407
Batteries (SmartKey) 407
High beam bulbs 412
Low beam bulbs 412
Rear lamp bulbs 410, 414
Wiper blades 415
Reset button 27
Resetting
All functions (control system) 158
Fuel consumption statistics 168
Trip odometer 141
Restraint systems 68
Emergency Tensioning Device
(ETD) 82
Infant and child restraints 85
Messages in the multifunction
display 373
Seat belts 68, 79
Resume function
Cruise control 217
Distronic* 225