window MERCEDES-BENZ SL65AMG 2007 R230 Owner's Guide

192 Controls in detailAutomatic climate controlActivating
Briefly press button,
(page 185).
The indicator lamp on the button
comes on.Deactivating

Briefly press button,
(page 185).
The indicator lamp on the button goes
out.
At outside temperatures above 79°F
(26 °C) the system will not automatically
switch back to outside air.Air recirculation mode with conve-
nience closing or opening feature
Activating

Press and hold button,.
The indicator lamp on the button
comes on. The air recirculation mode is
activated. The windows will close.
i
The air recirculation mode is activated auto-
matically


at high outside temperatures


if the concentration of carbon monoxide
(CO) and/or nitrogen oxide (NO
x) in the out-
side air increases, for example in a tunnel
The indicator lamp on button, is not lit when
the air recirculation mode is automatically
switched on.
A quantity of outside air is added after approxi-
mately 30 minutes.
i
The manually selected air recirculation
mode is deactivated automatically


after 5 minutes if the outside temperature is
below approximately 41°F (5 °C)


after 5 minutes if the air conditioning is
turned off


after 30 minutes if the outside temperature
is above approximately 41°F (5 °C)
Warning!
G
Never operate the windows if there is the
possibility of anyone being harmed by the
closing procedure.
In the event that the procedure causes po-
tential danger, the closing of the windows
can be immediately halted by releasing
the, button or by pressing and pulling
the respective window switch.

193 Controls in detail
Automatic climate control
Deactivating
Press and hold button,.
The indicator lamp on the button goes
out. The air recirculation mode is deac-
tivated. The windows will return to their
previous position.
Air conditioning
The air conditioning (cooling) function is
operational when the engine is running and
cools the vehicle interior down to the se-
lected temperature. In addition, the cool-
ing function dehumidifies the air in the
vehicle interior, thus preventing the win-
dows from fogging up.Deactivating
It is possible to deactivate the cooling
function of the automatic climate control
system. The air in the vehicle will then no
longer be cooled or dehumidified.

Press button 2 (
page 185).
The indicator lamp on the button goes
out. The cooling function switches off
after a short delay.
i
A window will only return to its previous po-
sition if it has not moved to another position us-
ing the respective window switch after it was
closed with button
,
.
i
Condensation may drip out from underneath
the vehicle. This is normal and not an indication
of a malfunction.Warning!
G
If you turn off the cooling function, the
vehicle will not be cooled when weather
conditions are warm. The windows can fog
up more quickly. Window fogging may
impair visibility and endanger you and
others.

194 Controls in detailAutomatic climate controlActivating
Moist air can fog up the windows. You can
dehumidify the air with the air condition-
ing.
Press button 2 once more
(page 185).
The indicator lamp on the button
comes on.
The air conditioning uses the refrigerant
R134A. This refrigerant is free of CFCs
which are harmful to the ozone layer.
Residual heat and ventilation
With the engine switched off, it is possible
to continue to heat or ventilate the interior
for up to 30 minutes. This feature makes
use of the residual heat produced by the
engine.Activating
With the SmartKey:

Turn the SmartKey in the starter switch
to position1 or0, or remove it from
the starter switch.

Press button T (
page 185).
The indicator lamp on the button
comes on.
With KEYLESS-GO*:

Turn off the engine by pressing the
KEYLESS-GO* start/stop button and
open the driver’s door (with the driver’s
door open, the starter switch is in posi-
tion 0, same as with the SmartKey re-
moved from the starter switch)

Press button T (
page 185).
The indicator lamp on the button
comes on.
!
If the 2 button on the automatic climate
control panel starts to flash, this indicates that
the air conditioning is losing refrigerant. The
compressor has turned off. The air conditioning
cannot be turned on again.


Have the air conditioning checked at the
nearest authorized Mercedes-Benz Center.
i
How long the system will provide heating de-
pends on the coolant temperature and the se-
lected temperature. The blower will run at low
speed regardless of the air distribution control
setting.

196 Controls in detailPower windowsOpening and closing the windows
The windows are opened and closed elec-
trically. The switches for all the windows
are on the driver’s door. The switch for the
passenger side windows is on the passen-
ger door.
1Left door and rear side windows
2Right door and rear side windows

Switch on the ignition (
page 39).
Warning!
G
When closing the windows, make sure that
there is no danger of anyone being injured
by the closing procedure.
The closing of the door windows can be im-
mediately halted by releasing the switch or,
if the switch was pulled past the resistance
point and released, by either pressing or
pulling the respective switch.
The closing of the rear side windows can be
immediately halted by releasing the switch.
If a door window encounters an obstruction
that blocks its path in a circumstance where
you pulled the switch past the resistance
point and released it to close the door win-
dow, the automatic reversal function will
stop the door window and open it slightly.
If the door window encounters an obstruc-
tion that blocks its path in a circumstance
where you are closing the door window by
pulling and holding the switch, by pressing
and holding button ‹on the SmartKey,
by pressing and holding the lock button (ve-
hicles with KEYLESS-GO*) on an outside
door handle, by pressing and holding the re-
tractable hardtop switch, or by pressing and
holding button,on the climate control
panel, the automatic reversal function will
not operate.
When leaving the vehicle, always remove the
SmartKey or the SmartKey with
KEYLESS-GO* from the starter switch, take
it with you, and lock the vehicle. Do not
leave children unattended in the vehicle, or
with access to an unlocked vehicle. Unsu-
pervised use of vehicle equipment can
cause an accident and/or serious personal
injury.i
Depending on the current position, the win-
dows may also open or close when the air recir-
culation button, on the control panel of the
automatic climate control (
page 191) is
pressed and held.
i
After switching off the ignition (
page 39)
or removing the SmartKey from the starter
switch, the windows can be operated


until you open a door


for at least 5 minutes if no door was opened

197 Controls in detail
Power windows
Opening the door windows
Press switch1 or2 to the resistance
point.
The corresponding door window will
move downwards until you release the
switch.
Opening the rear side windows when
the hardtop is closed:

Open the door window.

Press switch1 or 2 to the resistance
point again.
The corresponding rear side window
will open completely.Closing the door windows

Pull switch1 or2 to the resistance
point.
The corresponding door window will
move upwards until you release the
switch.
Closing the rear side windows if the
hardtop is closed:

Close the door window.

Pull and hold switch1 or 2.
The corresponding rear side window
will move upwards until you release the
switch. Fully opening the door windows
(Express-open)

Press switch1 or2 past the resis-
tance point and release.
The corresponding door window opens
completely.
i
If the hardtop is open, the respective rear
side window will also open automatically.
Warning!
G
If you pull and hold the switch up when clos-
ing the door window, and upward movement
of the door window is blocked by some ob-
struction including but not limited to arms,
hands, fingers, etc., the automatic reversal
will not operate.
i
If the hardtop is open, the respective rear
side window will also open automatically.

198 Controls in detailPower windowsFully closing the door windows
(Express-close)
Pull switch1 or2 past the resis-
tance point and release.
The corresponding door window closes
completely.
If the upward movement of the door win-
dow is blocked during the closing proce-
dure, the door window will stop and open
slightly.
Stopping windows

Press or pull the respective switch
again.Closing the windows with
KEYLESS-GO*

Press and hold lock button on an out-
side door handle (
page 64) until the
windows are closed.
Synchronizing power windows
The power window must be synchronized
each time

after the battery has been disconnect-
ed


if the power windows cannot be fully
opened (Express-open) or closed
(Express-close)
Synchronizing the power windows

Switch on the ignition (
page 39).

Pull the power window switches until
the side windows are closed.
Hold the switches for approximately
1 second.
The power windows are synchronized.
Warning!
G
Driver’s door only:
If within 5 seconds the switch is again
pulled past the resistance point and re-
leased, the automatic reversal will not
operate.
Warning!
G
When closing the windows make sure that
there is no danger of anyone being harmed
by the closing procedure.
The windows will not automatically re-open
if blocked during convenience closing.
If potential danger exists, proceed as fol-
lows:

Release the lock button.


Pull on the door handle and hold firmly.
The side windows open for as long as
the door handle is held but the door not
opened.

202 Controls in detailRetractable hardtop
Engage the parking brake (
page 54).

Close the luggage cover, see “Luggage
cover” (
page 205).

Close the trunk lid.
Opening (Summer opening feature)

Aim the transmitter eye at an outside
door handle.
The SmartKey must be in close proxim-
ity to the outside door handle.

Press and hold button Πuntil the
retractable hardtop is completely
open.
The seat ventilation* for the driver’s
seat switches on. The rear side win-
dows open.

Release button Πto interrupt pro-
cedure.
Closing (Convenience feature)

Aim the transmitter eye at the outside
door handle.
The SmartKey must be in close proxim-
ity to the outside door handle.

Press and hold button ‹until the
retractable hardtop is completely
closed.
The retractable hardtop and the rear
side windows close.Locking the retractable hardtop after
raising/lowering
If the retractable hardtop is not properly
locked, lock it as follows.
i
Make sure the retractable hardtop is dry be-
fore you open it. Otherwise water may enter the
trunk interior.
Warning!
G
The hardtop is not fully closed and locked or
not fully opened and locked if:

the message K
in operation

appears in the multifunction display


a warning sounds for 10 seconds and
the message K
Lock
retractable roof appears in the mul-
tifunction display when starting to drive

238 Controls in detailUseful features
Pull strap1 out of holder2.

Secure the luggage with the strap so
that it cannot move.

Insert strap1 into latch3.
Releasing strap

Press release button4 and guide
strap1 back to holder2.
Cup holders
1Left cup holder
2Right cup holder
Opening

Briefly press cup holder cover.
The cup holder opens automatically.
Warning!
G
The shelf below the rear window should not
be used to carry objects. This will avoid such
objects from being thrown about and injur-
ing vehicle occupants during an accident or
sudden maneuver.
The trunk is the preferred place to carry ob-
jects.
Warning!
G
In order to help prevent spilling liquids on
vehicle occupants and/or vehicle equip-
ment, only use containers that fit into the
cup holder. Use lids on open containers and
do not fill containers to a height where the
contents, especially hot liquids, could spill
during braking, vehicle maneuvers, or in an
accident. Liquids spilled on vehicle occu-
pants may cause serious personal injury.
Liquids spilled on vehicle equipment may
cause damage not covered by the
Mercedes-Benz Limited Warranty.
When not in use, keep the cup holder
closed. An open cup holder may cause injury
to or others when contacted during braking,
vehicle maneuvers, or in an accident.
Keep in mind that objects placed in the cup
holder may come lose during braking, vehi-
cle maneuvers, or in an accident and be
thrown around in the vehicle interior. Ob-
jects thrown around in the vehicle interior
may cause an accident and/or serious per-
sonal injury.

249 Controls in detail
Useful features
Call priority
If other service calls such as a Roadside
Assistance call or Information call are ac-
tive, an Emergency call is still possible. In
this case, the Emergency call will take pri-
ority and override all other active calls.
!
If the indicator lamps do not start flashing
after pressing one of the buttons or remain illu-
minated (in red) at any time, the Tele Aid system
has detected a malfunction or the service is cur-
rently not active, and may not initiate a call. Visit
an authorized Mercedes-Benz Center and have
the system checked or contact the Response
Center at 1-800-756-9018 (in the USA) or
1-888-923-8367 (in Canada) as soon as possi-
ble.
i
The indicator lamp in the respective button
flashes until the call is concluded. Calls can only
be terminated by a Response Center or Custom-
er Assistance Center representative except
Roadside Assistance and Information calls,
which can also be terminated by pressing button
t on the multifunction steering wheel or the
respective button for ending a telephone call on
the COMAND headunit.
!
If the indicator lamp continues to flash or
the system does not reset, contact the Response
Center at 1-800-756-9018 (in the USA) or
1-888-923-8367 (in Canada), or Mercedes-Benz
Customer Assistance at 1-800-FOR-MERCedes
(1-800-367-6372) in the USA or Customer Ser-
vice at 1-800-387-0100 in Canada.
i
When a Tele Aid call has been initiated, the
COMAND system audio is muted and the select-
ed mode (radio or CD) pauses. The optional cel-
lular phone (if installed) switches off. If you must
use this phone, the vehicle must be parked. Dis-
connect the coiled cord and place the call. The
COMAND navigation system (if engaged) will
continue to run. The display in the instrument
cluster is available for use and spoken com-
mands are only available by pressing the RPT
button on the COMAND unit. A pop-up window
will appear in the COMAND display to indicate
that a Tele Aid call is in progress.

267 Operation
Driving instructions
Road salts and chemicals can adversely af-
fect braking efficiency. Increased pedal
force may become necessary to produce
the normal brake effect.
Depressing the brake pedal periodically
when traveling at length on salt-strewn
roads can bring road-salt-impaired braking
efficiency back to normal.
If the vehicle is parked after being driven
on salt-treated roads, the braking efficien-
cy should be tested as soon as possible af-
ter driving is resumed.
For more information, see “Winter driving”
(
page 316).
Standing water
Warning!
G
Make sure not to endanger any other road
users when carrying out these braking ma-
neuvers.
Warning!
G
If the vehicle becomes stuck in snow, make
sure that snow is kept clear of the exhaust
pipe and from around the vehicle with the
engine running. Otherwise, deadly carbon
monoxide (CO) gases may enter vehicle in-
terior resulting in unconsciousness and
death.
To assure sufficient fresh air ventilation,
open a window slightly on the side of the ve-
hicle not facing the wind.Warning!
G
The outside temperature indicator is not de-
signed to serve as an Ice-Warning Device
and is therefore unsuitable for that purpose.
Indicated temperatures just above the freez-
ing point do not guarantee that the road sur-
face is free of ice.
!
Do not drive through flooded areas or water
of unknown depth. Before driving through water,
determine its depth. Never accelerate before
driving into water. The bow wave could force wa-
ter into the engine and auxiliary equipment, thus
damaging them.
If you must drive through standing water, drive
slowly to prevent water from entering the pas-
senger compartment or the engine compart-
ment. Water in these areas could cause damage
to electrical components or wiring of the engine
or transmission, or could result in water being in-
gested by the engine through the air intake,
causing severe internal engine damage. Any
such damage is not covered by the
Mercedes-Benz Limited Warranty.