ESP MERCEDES-BENZ SLK CLASS 2004 Owner's Manual

100 Controls in detailGood visibility
Sun visors
The sun visors protect you from sun glare
while driving.
Warning!
G
The automatic antiglare function does not
react if incoming light is not aimed directly
at sensors in the interior rear view mirror.
The interior rear view mirror and the exterior
rear view mirror on the driver’s side do not
react, for example, if the wind screen is in-
stalled.
Glare can endanger you and others.Warning!
G
In the case of an accident, liquid electrolyte
may escape from the mirror housing if the
mirror glass breaks.
Electrolyte has an irritating effect. Do not al-
low the liquid to come into contact with
eyes, skin, clothing, or the respiratory sys-
tem. In case it does, immediately flush af-
fected area with water, and seek medical
help if necessary.
Warning!
G
Exercise care when using the passenger
side exterior rear view mirror. The mirror
surface is convex (outwardly curved surface
for a wider field of view). Objects in mirror
are closer than they appear. Check your in-
terior rear view mirror or glance over your
shoulder before changing lanes.!Electrolyte drops coming into contact
with the vehicle paint finish can be
completely removed only while in the
liquid state by applying plenty of water.
Warning!
G
Do not use the vanity mirror while driving.
Keep the mirrors in the sun visors closed
while vehicle is in motion. Reflected glare
can endanger you and others.

101 Controls in detail
Good visibility
1Mirror cover
Swing sun visors down when you expe-
rience glare.

Push mirror cover1 to the side, as
required.
Rear window defroster
The rear window defroster uses a large
amount of power. To keep the battery
drain to a minimum, switch off the defrost-
er as soon as the rear window is clear. The
defroster is automatically deactivated af-
ter a maximum of 12 minutes.
Activating
Switch on the ignition.

Press buttonF (
page 102).
The indicator lamp on the button lights
up.
Deactivating

Press buttonF (
page 102) again.
The indicator lamp on the button goes
out.
Warning!
G
Any accumulation of snow and ice should be
removed from the rear window before driv-
ing. Visibility could otherwise be impaired,
endangering you and others.!If the rear window defroster switches
off too soon and the indicator lamp
starts blinking, this means that too
many electrical consumers are operat-
ing simultaneously and there is insuffi-
cient voltage in the battery. The system
responds automatically by deactivating
the rear window defroster.
As soon as the battery has sufficient
voltage, the rear window defroster au-
tomatically turns itself back on.

104 Controls in detailClimate control
Setting the temperature
Use temperature controls5 (
page 103)
to separately adjust the air temperature on
each side of the passenger compartment.
You should raise or lower the temperature
setting in small increments, preferably
starting at 72°F (22°C).Increasing

Turn the temperature control5
slightly upwards.
A red marking will be visible and the
climate control system will correspond-
ingly adjust the interior air tempera-
ture.
iThe selected temperature is reached as
quickly as possible.
Severe conditions (e.g. strong air pollu-
tion) may require replacement of the fil-
ter before its scheduled interval. A
clogged filter will reduce the air volume
to the interior.
If the vehicle interior is hot, ventilate
the interior before driving off.
Keep the air intake grille in front of the
windshield free of snow and debris.
iIf you use the standard settings for
heating or cooling the passenger com-
partment (
page 102), you will rarely
need to change the temperature, air
volume or air distribution.

105 Controls in detail
Climate control
Decreasing
Turn the temperature control5
slightly downwards.
A blue marking will be visible and the
climate control system will correspond-
ingly adjust the interior air tempera-
ture.
Adjusting air volume
Use air volume control9 (
page 103) to
adjust the air volume. The following sym-
bols are found on the control:
Adjusting air distribution
Use air distribution control6
(page 103) to adjust the air distribution.
The following symbols are found on the
control:
Symbol
Function
0
No ventilation
between0
andQ
Ventilation without a blow-
er, depending on the
speed driven
between1
and5
Ventilation with blower
Symbol
Function
cP
Directs air to the windows
b
Directs air into the passen-
ger compartment
d
Directs air to the footwells
a
Directs air through the
center, side and rear pas-
senger compartment air
vents

117 Controls in detail
Audio system
Seek tuning
Press either the f or e button.
The radio will tune to the next receiv-
able station.
Scan tuning

Press the
SC
key.
Each station with a strong signal on the
band selected will be tuned in for eight
seconds. The first scan will tune only
the stations with a high signal strength.
The second scan will tune every receiv-
able station.
By pressing either the d, c, f or
e buttons, or the
SC
key, the scan
mode can be cancelled.Station memory
Ten stations can be stored in the AM and
FM bands via the alpha-numeric keypad.
The “0” button corresponds to location 10.
Weatherband (WB) channels 1 to 7 can be
retrieved via the alpha-numeric keypad
and are preset at the factory.
Storing stations

Hold the number button down for ap-
proximately two seconds.
The currently displayed frequency is
stored on the selected station button.
The storage procedure is confirmed by
a short signal tone.
Retrieving a station from memory

Press the desired station button.Direct frequency input (AM and FM
only)

Select the band.

Press the “button and enter the
desired frequency using the
alpha-numeric keypad.
Frequencies outside of the frequency
ranges (frequencies specified
on (
page 116)) will not be accepted.
The frequency input mode is cancelled
if no button is pressed within four sec-
onds.

118 Controls in detailAudio systemCassette mode
Playing cassettes
Press the “TAPE” button.

Press the eject (EJ) key.
The display folds down and the cas-
sette slot becomes visible.

Push the cassette into the slot until it
engages.
The cassette will be pulled in automati-
cally.
The radio will switch to cassette mode.
Track 1 will be played and
SIDE 1
dis-
played. Track 1 is the side of the cassette
which is facing upwards. The cassette
deck will automatically detect the type of
tape and switch the equalization automati-
cally. A cassette symbol in the display indi-cates that a tape is in the mechanism. This
symbol appears in all modes but not in cas-
sette mode.
The cassette will not be ejected when the
radio is switched off or another mode is se-
lected.
If a cassette is in the mechanism, cassette
mode can be selected by using the “TAPE”
button. If no cassette has been inserted,
the display will show
NO TAPE
.
iDo not press directly on the radio dis-
play face.
Return the display panel to its normal
position by folding it back up and
pressing gently on the display frame to
lock in place.
When playing mono recorded tapes
(e.g. books) through a stereo system,
the sound from one track might bleed
to the other track, despite setting the
balance to the full left or full right
speakers.!If the display is in the down position for
more than 20 seconds, two successive
beeps will be heard. This will continue
at 5 second intervals until the display is
returned to its normal position.

121 Controls in detail
Audio system
CD mode
General notes on CD mode
Should excessively high temperatures oc-
cur while the audio system is in CD mode, TEMP HIGH
will appear in the display and
muting will take place. The unit will then
switch back to radio mode until the tem-
perature has decreased to a safe operating
level.
Should excessively low temperatures oc-
cur while the audio system is in CD mode,
TEMP LOW
will be displayed, but the CD will
still be played. It will be sensitive to skip-
ping if you are driving over rough roads.
Handle CDs carefully to prevent interfer-
ence during playback.
Avoid fingerprints and dust on CDs. Do not
write on the CDs or apply any label to the
CDs.
Clean CDs from time to time with a com-
mercially available cleaning cloth. No sol-
vents, anti-static sprays, etc. should be
used. Replace the CD in its container after use.
Protect CDs from heat and direct sunlight.
Only use CDs which bear the label shown
and that conform to the compact disc dig-
ital audio standard (IEC 60908). You can
therefore only use CDs with a maximum
thickness of 1.3 mm.
!Your CD drive has been designed to
play CDs which correspond to the EN
60908 standard. If you insert thicker
data carriers, e.g. ones that have data
on both sides (one side with DVD data,
the other side with audio data), they
cannot be ejected and will damage the
drive.
Use of CDs which do not meet this
standard may cause damage to the CD
changer. Do not play single-CDs
(80 mm) with an adapter.
Warning!
G
The CD changer* is a Class 1 laser product.
There is a danger of invisible laser radiation
if the cover is opened or damaged.
Do not remove the cover. The CD changer*
does not contain any parts which can be ser-
viced by the user. For safety reasons, have
any service work which may be necessary
performed only by qualified personnel.

123 Controls in detail
Audio system
CD changer* installed
1CD
2CD changer
3CD tray
4CD magazine
If a CD changer is installed, it can be oper-
ated from the front control panel of the ra-
dio. A loaded magazine must be installed
for CD playing.Loading/unloading the CD magazine

Slide the changer door to the right.

Press the eject button d.
The magazine will be ejected.

Remove the magazine.

Pull out the CD tray until its stop is
reached.

Place the CDs in the recess of the tray,
label side up.

Push the tray into the magazine in the
direction shown by the arrow.

Insert the loaded magazine into the
changer.Playing CDs

Press the CD button.
The CD most recently played will start
at the point where it was last switched
off. CDs stored in the magazine can be
selected by using the station preset
buttons 1-6.
The magazine slot number of the selected
CD will then be displayed after
CD. The
number of the track being played will be
displayed after
TRACK
.
If there is no CD in the selected magazine
slot,
NO CD
and the corresponding slot
number will be displayed (e.g.
NO CD3
). Af-
ter the last track on a CD has been played,
the next CD will automatically be selected
and played.
!Close the door after the magazine has
been inserted.

124 Controls in detailAudio systemSkipping tracks forwards / backwards
Press the f button.
The next track on the CD will be played.

Press the e button.
If the track has been playing for more
than ten seconds, it will revert to the
start of that track. If it has been playing
for less than ten seconds, it will revert
to the preceding track.
To skip several tracks, the respective
button must be pressed until the de-
sired track is reached. If the beginning
or end of the CD is reached during the
search, the first or last track will be
played.Fast forward/reverse

Press the d button and hold it down
for audible fast forward.

Press the c button and hold it down
for audible reverse.
The search will stop when the button is re-
leased. The relative time of the track will
be displayed during the search. The search
mode will cancel if the beginning or end of
the CD is reached.
Scanning

Press the
SC key.
Each track will be played for eight sec-
onds in ascending order.
The search will stop at the track in
question if the d, c, f, e
buttons or the
SC key are pressed.Random play/repeat function
The tracks of the current CD are played in
random order when the random feature
(
RDM
) is selected.

Press the
RDM
key to switch on, and
press
RDM
again to switch off.
When the repeat function (
RPT
) has been
selected, a particular track can be played
for as many times as desired.

Press the
RPT
key to switch on.

Press
RPT
again to switch off.
iBoth functions cannot be used simulta-
neously.

128 Controls in detailPower windows
Power windowsOpening and closing the windows
The side windows can be opened and
closed electrically. The switches for the
side windows are on the lower part of the
center console.
1Power window switch

Turn key in the steering lock to
position1 or2.Opening the windows

Press switch at the symbolk to the
resistance point.
The corresponding window will move
downwards until you release the
switch.
Closing the windows

Press switch at the symbolj.
The corresponding window will move
upwards until you release the switch.
Fully opening the windows (Ex-
press-open)

Press switch at the symbolk past
the resistance point and release.
The corresponding window opens com-
pletely.
Stopping windows

Briefly press switch atk orj.
Warning!
G
When closing the windows, make sure there
is no danger of anyone being harmed by the
closing procedure.
The closing of the door windows can be im-
mediately halted by releasingj.
When leaving the vehicle, always remove the
key from steering lock and lock your vehicle.
Do not leave children unattended in the ve-
hicle, or with access to an unlocked vehicle.
Unsupervised use of vehicle equipment can
cause an accident and/or serious personal
injury.iThe power windows can also be
operated with the retractable hardtop
switch (
page 132).