lock MERCEDES-BENZ SLK CLASS 2007 Owners Manual

389 Practical hints
Unlocking/locking in an emergency
Insert mechanical key 2 into the
driver’s door lock until it stops.
Turn mechanical key 2 clockwise to
position1.
The driver’s door is locked.
Turn back mechanical key 2 and
remove it from driver’s door lock.Manually unlocking the gear selector
lever (automatic transmission*)
In case of power failure, the gear selector
lever can be manually unlocked, e.g. to tow
the vehicle.
1Gear selector lever cover
2Release
Insert flat, blunt object (e.g. screw-
driver) into the left edge of cover1 at
the position indicated by the arrows.
Loosen cover1 using this object.
Using your hands, pull cover1 out
and remove.
Push down and hold release2 in
direction of arrow.
Simultaneously move gear selector
lever out of positionP.
The gear selector lever is unlocked
now.1Locking
2Mechanical key
iThis procedure does not arm the anti-theft
alarm system, nor does it lock the fuel filler flap.
iThe gear selector lever is locked again as
soon as you place it in positionP again.

390 Practical hints
Opening/closing in an emergency
Raising retractable hardtop manually
Warning!G
If the retractable hardtop does not com-
pletely open or close, the roof hydraulics will
lose pressure and the retractable hardtop is
lowered

after approximately 7 minutes when the
ignition is switched on

after approximately 15 seconds when
the ignition is switched off
Shortly before the hardtop is lowered, a
warning will sound. In the multifunction dis-
play you will seeK and the message
Retractable roof being opened.

Properly lock retractable hardtop before
continuing to drive (
page 240).
Warning!G
Manually closing the retractable hardtop is a
complicated and technically demanding pro-
cedure and should only be performed by an
authorized Mercedes-Benz Center or quali-
fied technician. Attempting to manually
close the retractable hardtop may cause
damage to the retractable hardtop and/or
personal injury.
Warning!G
To prevent possible accidents, drive the
vehicle only with the retractable hardtop
either completely closed and locked, or fully
lowered into its storage compartment.

391 Practical hints
Replacing SmartKey batteries
Replacing SmartKey batteries
If the batteries in the SmartKey are
discharged, the vehicle can no longer be
locked or unlocked. It is recommended
to have the batteries replaced at an autho-
rized Mercedes-Benz Center.Batteries contain materials that can harm
the environment if disposed of improperly.
Recycling of batteries is the preferred
method of disposal. Many states require
sellers of batteries to accept old batteries
for recycling.SmartKey
Replacement batteries: Lithium, type
CR 2025 or equivalent.
Remove the mechanical key from the
SmartKey (
page 387).
1Mechanical key
2Battery compartment
Insert mechanical key1 into opening.
Press mechanical key1 in direction of
arrow.
Battery compartment2 is unlatched.
Pull battery compartment2 out of the
housing.
Warning!G
Batteries contain poisonous and corrosive
substances. Therefore keep the batteries
out of reach of children.
If a battery is swallowed, seek medical help
immediately.
iWhen inserting the batteries, make sure
they are clean and free of lint.
iWhen replacing batteries, always replace
both batteries.
The required replacement batteries are available
at any Mercedes-Benz Center.


392 Practical hints
Replacing SmartKey batteries
3Batteries
4Contact springs
Pull out batteries 3.
Using a lint-free cloth, insert new
batteries3 under contact springs4
with the positive terminal (+) side
facing up.
Return battery compartment2
(
page 391) into the housing until it
locks into place.
Slide the mechanical key back into the
SmartKey.
Check the operation of the SmartKey.


397 Practical hints
Replacing bulbs
Low beam bulb (Halogen headlamps
only)
Turn housing cover1 counterclock-
wise and remove.
Turn bulb socket5 with the bulb
counterclockwise and remove.
Pull the bulb out of bulb socket5.
Press the new bulb into bulb socket5.
Place bulb socket5 back into the
lamp and turn it clockwise.
Reinstall housing cover1.
High beam/high beam flasher bulb
(Halogen headlamps) / High beam
flasher bulb (Bi-Xenon* headlamps)
Turn bulb socket3 with the bulb
counterclockwise and remove.
Pull the bulb out of bulb socket3.
Press the new bulb into bulb socket3.
Place bulb socket3 back into the
lamp and turn it clockwise.Front turn signal bulb
Turn bulb socket2 with the bulb
counterclockwise and remove.
Press gently onto the bulb and turn it
counterclockwise out of bulb
socket2.
Press the new bulb gently into bulb
socket2 and turn it clockwise.
Place bulb socket2 back into the
lamp and turn it clockwise.
Parking and standing lamp bulb
Turn bulb socket4 with the bulb
counterclockwise and remove.
Pull the bulb out of bulb socket4.
Press the new bulb into bulb socket4.
Place bulb socket4 back into the
lamp and turn it clockwise.
Replacing bulbs for rear lamps
Before you start to replace a bulb for a rear
lamp, do the following first:
Turn the exterior lamp switch to
positionM (
page 109).
Open the trunk lid (page 100).
Tail lamp unit
1Bulb socket for rear fog lamp
(driver’s side only)
2Bulb socket for turn signal lamp
3Bulb socket for backup lamp

398 Practical hints
Replacing bulbs
Fold corresponding trim to side.
Turn the respective bulb socket coun-
terclockwise and remove.
Press gently onto the bulb and turn
counterclockwise out of its bulb sock-
et.
Press the new bulb gently into its bulb
socket and turn clockwise.
Reinstall the bulb socket and turn
clockwise until it engages.
Reinstall trim.License plate lamp
1ScrewsLoosen both screws1.
Remove the license plate lamp.
Replace the bulb.
Reinstall the license plate lamp.
Retighten screws1.

407 Practical hints
Flat tire
Mounting the spare wheel
Preparing the vehicle
Prepare the vehicle as described
(
page 401).
Take the spare wheel, wheel wrench,
wheel bolts, jack, and electric air pump
out of the trunk (
page 382).Lifting the vehicle
Prevent the vehicle from rolling away
by blocking wheels with wheel chocks
(not included) or other sizeable ob-
jects.
One wheel chock is included with the
vehicle tool kit (
page 383).
When changing wheel on a level surface:
Place one wheel chock or other size-
able object in front of and another
wheel chock or other sizeable object
behind the wheel that is diagonally
opposite to the wheel being changed.
Always try lifting the vehicle using the jack
on a level surface. However, should cir-
cumstances require you to do so on a hill,
place the wheel chock or other sizeable
object and the other wheel chock or other
sizeable object as follows:
Place wheel chocks and other sizeable
objects on the downhill side blocking
both wheels of the axle not being
worked on.
Warning!G
The dimensions of the spare wheel are dif-
ferent from those of the road wheels. As a
result, the vehicle handling characteristics
change when driving with a spare wheel with
collapsible tire mounted. Adapt your driving
style accordingly.
The spare wheel is for temporary use only.
When driving with spare wheel mounted,
ensure proper tire inflation pressure and do
not exceed vehicle speed of 50 mph
(80 km/h).
Drive to the nearest Mercedes-Benz Center
as soon as possible to have the spare wheel
replaced with a regular road wheel.
Never operate the vehicle with more than
one spare wheel mounted.
Do not switch off the ESP
® when a spare
wheel is mounted.

408 Practical hints
Flat tire
1Wheel wrench
On wheel to be changed, loosen but do
not yet remove the wheel bolts in direc-
tion of arrow (approximately one full
turn with wheel wrench1).
The jack take-up brackets are located di-
rectly behind the front wheel housings and
in front of the rear wheel housings.2Jack
3Take-up bracketPlace jack2 on firm ground.
Position jack2 under take-up
bracket3 so that it is always vertical
(plumb-line) as seen from the side,
even if the vehicle is parked on an
incline.
Warning!G
The jack is designed exclusively for jacking
up the vehicle at the jack take-up brackets
built into either side of the vehicle. To help
avoid personal injury, use the jack only to lift
the vehicle during a wheel change. Never
get beneath the vehicle while it is supported
by the jack. Keep hands and feet away from
the area under the lifted vehicle. Always
firmly set parking brake and block wheels
before raising vehicle with jack.
Do not disengage parking brake while the
vehicle is raised. Be certain that the jack is
always vertical (plumb line) when in use, es-
pecially on hills. Always try to use the jack
on level surface. Be sure the jack arm is fully
seated in the jack take-up bracket. Always
lower the vehicle onto sufficient capacity
jackstands before working under the
vehicle.
Warning!G
Position the jack only on the jack take-up
brackets designed for this purpose.
If the jack is not properly positioned, the
vehicle may fall off of the jack.

413 Practical hints
Flat tire
Lowering the vehicle
Lower vehicle by turning the crank
counterclockwise until vehicle is
resting fully on its own weight.
Remove the jack.
1-5 Wheel bolts
Tighten the five wheel bolts evenly in
the direction of the arrow, following the
diagonal sequence illustrated
(1to5), until all bolts are tight.
Observe a tightening torque of
80 lb-ft (110 Nm).
Fully collapse the jack.
Place the vehicle tool kit, electric air
pump, and the jack back in the storage
compartment underneath the trunk
floor.
Wrap the damaged wheel in the protec-
tive sheet provided with the vehicle
tool kit and put the wheel in the trunk.
For information on storing the spare wheel
in the trunk after it has been replaced by a
regular road wheel, see “Storing the spare
wheel with collapsible tire” (
page 385).
Warning!G
Inflate the collapsible tire using the electric
pump (
page 411) before lowering the
vehicle.
Warning!G
Have the tightening torque checked after
changing a wheel. The wheels could come
loose if they are not tightened to a torque of
80 lb-ft (110 Nm).
iThe flat tire may be transported in the trunk
when the retractable hardtop is closed.

416 Practical hints
Battery
Disconnecting the battery
1Water tray
2Lock
Apply the parking brake (page 59).
Make sure the gear selector lever* is
set to positionP (manual transmission
to Neutral).
Turn off all electrical consumers.
Remove the SmartKey from the starter
switch.
Open the hood (page 294).
Turn locks2 one quarter turn.
Remove water tray1.
Read and observe safety instructions
and precautions (
page 303) and
(
page 415).
Use a 10 mm open-end wrench to dis-
connect the negative lead from battery
negative terminal3 (
page 415).
Remove the cover from battery positive
terminal 2 (
page 415).
Use a 10 mm open-end wrench to dis-
connect the positive lead from battery
positive terminal2 (
page 415).
Warning!G
With a disconnected battery

you will no longer be able to turn the
SmartKey in the starter switch

automatic transmission*: the gear se-
lector lever will remain locked in
positionP
!Always disconnect the battery in the order
described below. Otherwise the vehicle’s
electronics can be damaged.