instrument cluster MERCEDES-BENZ SLK CLASS 2007 User Guide

53 Getting started
Driving
Parking brake
1Parking brake lever
2Release button
Pull up slightly on parking brake
lever1 and press release button2.
Push parking brake lever1 down to
its original position.
The brake warning lamp; (USA
only) or3 (Canada only) in the
instrument cluster goes out.
Driving off
Warning!G
When leaving the vehicle, always remove the
SmartKey from the starter switch, take it
with you, and lock the vehicle. Do not leave
children unattended in the vehicle, or with
access to an unlocked vehicle. Children
could release the parking brake, which
could result in an accident and/or serious
personal injury.
Warning!G
On slippery road surfaces, never downshift
in order to obtain braking action. This could
result in drive wheel slip and reduced vehi-
cle control. Your vehicle’s ABS will not pre-
vent this type of loss of control.
!If you hear a warning signal and the
message
Release parking brake appears in
the multifunction display when driving off, you
have forgotten to release the parking brake.
Release the parking brake (
page 53).
!Do not run cold engine at high engine speed.
Running a cold engine at high engine speed may
shorten the service life of the engine.
!Simultaneously depressing the accelerator
pedal and applying the brakes reduces engine
performance and causes premature brake and
drivetrain wear.

55 Getting started
Driving
Switching on headlamps
Low beam headlamps
The exterior lamp switch is located on the
dashboard to the left of the steering wheel.
Exterior lamp switch
1Off
2Low beam headlamps on
Turn the exterior lamp switch to
positionB.
The low beam headlamps come on.High beam
The combination switch is located on the
left of the steering column.
Combination switch
1High beam
2High beam flasher
Push the combination switch in
direction of arrow1.
The high beam headlamps and high
beam headlamp indicator lampA in
the instrument cluster come on
(
page 26).
For more information on headlamps, see
“Lighting” (
page 109).
Turn signals
The combination switch is located on the
left of the steering column.
Combination switch
1Turn signals, right
2Turn signals, left

56 Getting started
Driving
Press the combination switch in
direction of arrow1 or2.
The corresponding turn signal indicator
lampKorL in the instrument
cluster flashes (
page 26).
The combination switch resets auto-
matically after major directional chang-
es.
Windshield wipers
The combination switch is located on the
left of the steering column.
Combination switch
1Single wipe
Wiping with windshield washer fluid
2Switching on windshield wipers
Switch on the ignition (page 37).
iTo signal minor directional changes such as
changing lanes, press combination switch only
to point of resistance and release. The corre-
sponding turn signals will flash three times.
!Do not operate the windshield wipers when
the windshield is dry. Dust that accumulates on
a windshield might scratch the glass and/or
damage the wiper blades when wiping occurs on
a dry windshield. If it is necessary to operate the
windshield wipers in dry weather conditions,
always operate the windshield wipers with
windshield washer fluid (
page 58).
!If anything blocks the windshield wipers
(leaves, snow, etc.), switch them off
immediately.

For safety reasons, stop the vehicle in a safe
location, turn off the engine and remove the
SmartKey from the starter switch before
attempting to remove any blockage.

Remove blockage.

Turn the windshield wipers on again.
If the windshield wipers fail to function at all with
the combination switch in positionI,

set the combination switch to the next
higher wiper speed

have the windshield wipers checked at the
nearest authorized Mercedes-Benz Center

64 Safety and Security
Occupant safety
In this section you will learn the most
important facts about the restraint system
components of the vehicle.

Seat belts (page 76)

Child restraints (page 80)
Additional protection potential provided by

Supplemental Restraint System (SRS)
with

Air bags (page 66)

Air bag control unit (with crash
sensors)

Emergency Tensioning Device
(ETD) for seat belts (
page 79)Air bag system components with

Front passenger front air bag off
indicator lamp (
page 74)

Passenger seat with Occupant
C
lassification System (OCS)
(
page 71)
Although independent systems, their
protective functions work in conjunction
with each other.The SRS system conducts a self-test when
the ignition is switched on and in regular
intervals while the engine is running. This
facilitates detection of malfunctions. The
1indicator lamp in the instrument
cluster comes on when the ignition is
switched on and goes out no later than a
few seconds after the engine has been
started.
The SRS components are in operational
readiness if the 1indicator lamp is not
lit when the engine is running.
A malfunction in the system has been
detected if the 1indicator lamp:

fails to go out after approximately
4 seconds after the engine was started

does not come on at all

comes on after the engine was started
or while driving
iFor information on infants and children
traveling with you in the vehicle and restraint
systems for infants and children, see “Children
in the vehicle” (
page 79).

84 Safety and Security
Driving safety systems
In this section you will find information on
the following driving safety systems:

ABS (Antilock Brake System)

BAS (Brake Assist System)

ESP® (Electronic Stability Program)
ABS
The Antilock Brake System (ABS) regulates
the brake pressure so that the wheels do
not lock during braking. This allows you to
maintain the ability to steer your vehicle.
The ABS is functional above a speed of
approximately 5 mph (8 km/h) indepen-
dent of road surface conditions.
On slippery road surfaces, the ABS will
respond even to light brake pressure.
The -indicator lamp in the instrument
cluster (
page 26) comes on when you
switch on the ignition. It goes out when the
engine is running.
Warning!G
The following factors increase the risk of
accidents:

Excessive speed, especially in turns

Wet and slippery road surfaces

Following another vehicle too closely
The driving systems described in this sec-
tion cannot reduce these risks or prevent
the natural laws of physics from acting on
the vehicle.
Always adjust your driving style to the
prevailing road and weather conditions and
keep a safe distance to other road users and
objects on the street.
iIn winter operation, the maximum
effectiveness of the ABS, the BAS, and the ESP®
is only achieved with winter tires (
page 332)
or snow chains as required.
Warning!G
Do not pump the brake pedal. Use firm,
steady brake pedal pressure instead. Pump-
ing the brake pedal defeats the purpose of
the ABS and significantly reduces braking
effectiveness.

86 Safety and Security
Driving safety systems
BAS
The Brake Assist System (BAS) operates in
emergency situations. If you apply the
brakes very quickly, the BAS automatically
provides full brake boost, thereby poten-
tially reducing braking distance.
Apply continuous full braking pressure
until the emergency braking situation is
over.
The ABS will prevent the wheels from
locking.
When you release the brake pedal, the
brakes function again as normal. The BAS
is then deactivated.
ESP®
The Electronic Stability Program (ESP®) is
operational as soon as the engine is run-
ning and monitors the vehicle’s traction
(force of adhesive friction between the
tires and the road surface) and handling.
The ESP
® recognizes when a wheel is spin-
ning or if the vehicle starts to skid.
By applying the brakes to the appropriate
wheel and by limiting the engine output,
the ESP
® works to stabilize the vehicle.
The ESP® is especially useful while driving
off and on wet or slippery road surfaces.
The ESP
® also stabilizes the vehicle during
braking and steering maneuvers.
The ESP
® warning lampv in the
instrument cluster flashes when the ESP®
is engaged.
The ESP
® warning lampv in the
instrument cluster comes on when you
switch on the ignition. It goes out when the
engine is running.
Warning!G
If the BAS is malfunctioning, the brake
system is still functioning normally, but
without the additional brake boost available
that BAS would normally provide in an emer-
gency braking maneuver. Therefore, the
braking distance may increase.
Warning!G
The BAS cannot prevent the natural laws of
physics from acting on the vehicle, nor can
it increase braking efficiency beyond that
afforded by the condition of the vehicle
brakes and tires or the traction afforded.
The BAS cannot prevent accidents, includ-
ing those resulting from excessive speed in
turns, following another vehicle too closely,
or hydroplaning. Only a safe, attentive, and
skillful driver can prevent accidents.
The capabilities of a BAS equipped vehicle
must never be exploited in a reckless or
dangerous manner which could jeopardize
the user’s safety or the safety of others.

89 Safety and Security
Driving safety systems
The ESP® switch is located on the upper
part of the center console.
1ESP
® switch
With the engine running, press ESP®
switch1 until the ESP® warning
lampv in the instrument cluster
comes on.
The ESP
® is switched off.Switching on the ESP
®

Press ESP® switch1 until the ESP®
warning lampv in the instrument
cluster goes out.
You are now again in normal driving
mode with the ESP
® switched on.
iWhen the ESP® is switched off and one
or more drive wheels are spinning, the
ESP
®warning lampv in the instrument
cluster flashes. However, the ESP® will then not
stabilize the vehicle.
Warning!G
When the ESP® warning lampv is illumi-
nated continuously, the ESP® is switched off
or is not operational due to a malfunction.
Vehicle stability in standard driving maneu-
vers reduces.
Adapt your speed and driving to the prevail-
ing road conditions and to the non-operating
status of the ESP
®.
!Avoid spinning of a drive wheel for an
extended period with the ESP® switched off. This
may cause serious damage to the drivetrain
which is not covered by the Mercedes-Benz
Limited Warranty.

93 Controls in detail
Locking and unlocking
Seats
Memory function*
Lighting
Instrument cluster
Control system
Manual transmission
Automatic transmission*
Good visibility
Climate control
Automatic climate control*
Audio system
Power windows
Retractable hardtop
Driving systems
Loading
Useful features

113 Controls in detail
Lighting
Rear fog lamp (driver’s side only)
Switch on the low beam
headlampsB (
page 112).
Pull out the exterior lamp switch to
second stop.
The front fog lamps and the rear fog
lamp switch on.
The yellow indicator lamp† in the
exterior lamp switch comes on
(
page 109).
Push in the exterior lamp switch to first
stop.
The rear fog lamp switches off.
The yellow indicator lamp† in the
exterior lamp switch goes out.
The front fog lamps remain lit.
Combination switch
1High beam
2High beam flasherHigh beam
Turn the exterior lamp switch to
positionB (
page 109).
Push the combination switch in
direction of arrow1 to switch on the
high beam.
The high beam headlamp indicator
lampA in the instrument cluster
comes on (
page 26).
Pull the combination switch in direction
of arrow2 to its original position to
switch off the high beam.
The high beam headlamp indicator
lampA in the instrument cluster
goes out.
High beam flasher
Pull the combination switch briefly in
direction of arrow2.

118 Controls in detail
Instrument cluster
A full view illustration of the instrument
cluster can be found in the “At a glance”
section (
page 26).
1To brighten instrument cluster
illumination (knob+)
2To dim instrument cluster
illumination (knob-)
3Reset buttonJ
The instrument cluster is activated when
you

open a door

switch on the ignition (page 37)

press reset buttonJ

switch on the exterior lampsFor information on changing the instru-
ment cluster settings, e.g. the language,
see “Instrument cluster submenu”
(
page 139).Adjusting instrument cluster
illumination
Adjusting
Use knobs 1 or 2 to adjust the illumina-
tion brightness of the instrument cluster.
To brighten illumination
Press knob1 briefly.
The instrument cluster illumination
brightens.
To dim illumination
Press knob2 briefly.
The instrument cluster illumination
dims.
iOpening a door or pressing the reset
buttonJ without switching on the ignition or
the exterior lighting activates the multifunction
display illumination only for 30 seconds.
Warning!G
No messages will be displayed if either the
instrument cluster or the multifunction
display is inoperative.
As a result, you will not be able to see
information about your driving conditions,
such as speed or outside temperature,
warning/indicator lamps,
malfunction/warning messages or the
failure of any systems. Driving characteris-
tics may be impaired.
If you must continue to drive, do so with
added caution. Contact an authorized
Mercedes-Benz Center as soon as possible.
iThe instrument cluster illumination
automatically adjusts to the ambient light.
You can only adjust the brightness of the instru-
ment cluster illumination when it is dark outside.
iWith the exterior lighting switched on, the
brightness of the switches in the center console
will also be adjusted when using knob 1 or 2.